Motorola MC319Z RFID Owner's manual

MC319Z RFID
Regulatory Guide
Microsoft®Mobile®6.5

2 MC319Z RFID
© 2015 ZIH Corp and/or its affiliates. All rights reserved.
Zebra reserves the right to make changes to any product to improve reliability,
function, or design.
Zebra does not assume any product liability arising out of, or in connection with,
the application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise
under any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Zebra products might
be used. An implied license exists only for equipment, circuits, and subsystems
contained in Zebra products.
Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in
many jurisdictions worldwide. All other trademarks are the property of their
respective owners.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Warranty
For the complete Zebra hardware product warranty statement, go to:
www.zebra.com/warranty.
For Australia Only:
This warranty is given by Zebra Technologies Asia Pacific Pte. Ltd., 71 Robinson
Road, #05-02/03, Singapore 068895, Singapore. Our goods come with
guarantees that cannot be excluded under the Australia Consumer Law. You are
entitled to a replacement or refund for a major failure and compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Zebra Technologies Corporation Australia’s limited warranty above is in addition
to any rights and remedies you may have under the Australian Consumer Law. If
you have any queries, please call Zebra Technologies Corporation at+65 6858
0722. You may also visit our website: http://www.zebra.com for the most updated
warranty terms.

Regulatory Guide 3
Health and Safety Recommendations
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury follow
the recommendations below. To prevent employee injury, consult with the local
Health & Safety Manager to ensure compliance with the required safety
programs.
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures
Regulatory Information
This guide applies to the following Model Numbers: MC319ZEU, MC319ZUS.
All Zebra devices are designed to be compliant with rules and regulations in
locations they are sold and will be labeled as required.
Local language translations are available at the following website:
www.zebra.com/support.
Any changes or modifications to Zebra equipment, not expressly approved by
Zebra, could void the user's authority to operate the equipment.
Only use Zebra approved and UL Listed accessories, battery packs and battery
chargers.
Do NOT attempt to charge damp/wet mobile computers or batteries. All
components must be dry before connecting to an external power source.
Declared maximum operating temperature: 50 Degrees Centigrade
Radio Devices
This device is approved under the Zebra brand.
Model Numbers for Regulatory Certification:
• MC319ZUS - Frequency 902 - 928 MHz (Maximum)
• MC319ZEU - Frequency 865 - 868 MHz

4 MC319Z RFID
Bluetooth®Wireless Technology
This is an approved Bluetooth® product. For more information or to view End
Product Listing, please visit https://www.bluetooth.org/tpg/listings.cfm.
Wireless Device Country Approvals
Regulatory markings, subject to certification, are applied to the device signifying
the radio is approved for use in the following countries: United States, Canada,
China, S. Korea, Australia, and Europe1.
Please refer to the Zebra Declaration of Conformity (DoC) for details of other
country markings. This is available at www.zebra.com/doc.
Note1: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium,
Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak
Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
Operation of the device without regulatory approval is illegal.
Country Selection - Worldwide Version Only
Select only the country in which you are using the device. Any other selection will
make the operation of this device illegal.
Frequency of Operation - FCC
The range of channels is limited by firmware.
Country Roaming - Worldwide Version only
This device incorporates the International Roaming feature (IEEE802.11d) which
will ensure the product operates on the correct channels for the particular country
of use.
Ad-Hoc Operation
Ad-Hoc operation is limited to Channels 36-48 (5150-5250 MHz). Use of this band
is restricted to Indoor Use Only, any other use will make the operation of this
device illegal.

Regulatory Guide 5
Frequency of Operation – FCC and IC
5 GHz Only
The use in the UNII (Unlicensed National Information Infrastructure) band 1
(5150-5250 MHz) and the band 5.470-5.725 MHz is restricted to Indoor Use Only;
any other use will make the operation of this device illegal.
Industry Canada statement:
Caution:
The device for the band 5150-5250 MHz and the band 5.470-5.725 MHz is only
for indoor usage to reduce potential for harmful interference to co-channel mobile
satellite systems.
High power radars are allocated as primary users (meaning they have priority) of
5250-5350 MHz and 5650-5850 MHz and these radars could cause interference
and/or damage to LE-LAN devices.
Avertissement:
Le dispositif fonctionnant dans la bande 5150-5250 MHz, 5.470-5.725 MHz est
réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de
brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes
canaux.
Les utilisateurs de radars de haute puissance sont désignés utilisateurs
principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5250-5350 MHz et
5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des
dommages aux dispositifs LAN-EL.

6 MC319Z RFID
Please observe all warning notices with regard to the usage of wireless devices.
Potentially Hazardous Atmospheres
You are reminded of the need to observe restrictions on the use of radio devices
in fuel depots, chemical plants etc. and areas where the air contains chemicals or
particles (such as grain, dust, or metal powders) and any other area where you
would normally be advised to turn off your vehicle engine.
Safety in Aircraft
Switch off your wireless device whenever you are instructed to do so by airport or
airline staff. If your device offers a 'flight mode' or similar feature, consult airline
staff as to its use in flight.
Safety in Hospitals
This device is not part of a life-support system.
Wireless devices transmit radio frequency energy and may affect medical
electrical equipment.
Wireless devices should be switched off wherever you are requested to do so in
hospitals, clinics or healthcare facilities. These requests are designed to prevent
possible interference with sensitive medical equipment.
Pacemakers
Pacemaker manufacturers recommended that a minimum of 15 cm (6 inches) be
maintained between a handheld wireless device and a pacemaker to avoid
potential interference with the pacemaker. These recommendations are
consistent with independent research and recommendations by Wireless
Technology Research.
Persons with pacemakers:
• Should ALWAYS keep the device more than 15cm (6 inches) from their
pacemaker when turned ON.
• Should not carry the device in a breast pocket.
• Should use the ear furthest from the pacemaker to minimize the potential for
interference.
• If you have any reason to suspect that interference is taking place, turn OFF
your device.
Warnings for Use of Wireless Devices

Regulatory Guide 7
Other Medical Devices
Please consult your physician or the manufacturer of the medical device, to
determine if the operation of your wireless product may interfere with the medical
device.
Note: Under certain adverse conditions, interference may be experienced when
using ActiveSync; if this occurs, switch off the terminal and re-start ActiveSync.
Safety Information
Reducing RF Exposure - Use Properly
Only operate the device in accordance with the instructions supplied.
International
The device complies with internationally recognized standards covering human
exposure to electromagnetic fields from radio devices. For information on
“International” human exposure to eletromagnic fields refer to the Zebra
Declaration of Conformity (DoC) at
www.zebra.com/doc.
Europe
For RFID operation, to comply with EU RF exposure requirements, this device
must be operated in the hand with a minimum separation distance of 23cm or
more from a person's body. Other operating configurations should be avoided.
US and Canada
For RFID operation, to satisfy FCC RF exposure requirements, a mobile
transmitting device must operate with a minimum separation distance of 23cm or
more from a person's body.
Co-located Statement
To comply with FCC RF exposure compliance requirement, the antenna used for
this transmitter must not be co-located or operating in conjunction with any other
transmitter/antenna except those already approved in this filing.
RF Exposure Guidelines

8 MC319Z RFID
Industry Canada Statement
IMPORTANT NOTE: (For mobile device use)
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles)
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC
établies pour un environnement non contrôlé. Cet équipement doit être installé et
utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et
votre corps.
Laser Devices
Complies with 21CFR1040.10 and 1040.11 except for deviations pursuant to
Laser Notice No. 50, dated June 24, 2007.
EN60825-1: 2007
IEC60825-1 (Ed. 2.0)
The laser classification is marked on one of the labels on the device.
Class 2 laser scanners use a low power, visible light diode. As with any very bright
light source, such as the sun, the user should avoid staring directly into the light
beam. Momentary exposure to a Class 2 laser is not known to be harmful.

Regulatory Guide 9
Scanner Labeling
Power Supply
Use ONLY a LISTED, Type no. 50-14000 (5.4Vdc, 3A), PWRS-14000 (5.4Vdc,
3A), or KT -14000 (5.4V, 3A), direct plug-in power supply, marked Class 2 or LPS
(IEC60950-1, SELV). Use of alternative Power Supply will invalidate any
approvals given to this unit and may be dangerous.
Batteries
Taiwan - Recycling
EPA (Environmental Protection Administration) requires dry
battery producing or importing firms in accordance with Article
15 of the Waste Disposal Act are required to indicate the
recycling marks on the batteries used in sales, giveaway or
promotion. Contact a qualified Taiwanese recycler for proper battery disposal.
⊼ ᛣ˖ᠧᓔᯊঞ㘨䫕༅ᬜᯊ᳝▔ܝ䕤ᇘ ࣓Ⳉ㾚ܝᴳ
COMPLIES WITH 21CFR1040.10 AND 1040.11 EXCEPT FOR
DEVIATIONS PURSUANT TO LASER NOTICE NO. 50,
DATED JUNE 24, 2007 AND IEC 60825-1 (Ed. 2.0) EN60825-1:2007
CAUTION- CLASS 2 LASER LIGHT WHEN OPEN. DO NOT STARE INTO THE
BEAM.
ATTENTION- LUMIÉRE LASER DE CLASSE 2 EN CAS D'OUVERTURE.
NE PAS REGARDER DANS LE FAISCEAU.
VORSICHT- LASERLICHT KLASSE 2, WENN ABDECKUNG GEÖFFNET. NICHT
IN DEN STRAHL BLICKEN.

10 MC319Z RFID
Battery Information
Zebra rechargeable battery packs are designed and constructed to the highest
standards within the industry.
However, there are limitations to how long a battery can operate or be stored
before needing replacement. Many factors affect the actual life cycle of a battery
pack, such as heat, cold, harsh environmental conditions and severe drops.
When batteries are stored over six (6) months, some irreversible deterioration in
overall battery quality may occur. Store batteries at half of full charge in a dry, cool
place, removed from the equipment to prevent loss of capacity, rusting of metallic
parts and electrolyte leakage. When storing batteries for one year or longer, the
charge level should be verified at least once a year and charged to half of full
charge.
Replace the battery when a significant loss of run time is detected.
Standard warranty period for all Zebra batteries is 30 days, regardless if the
battery was purchased separately or included as part of the mobile computer or
bar code scanner.
Battery Safety Guidelines
• The area in which the units are charged should be clear of debris and
combustible materials or chemicals. Particular care should be taken where the
device is charged in a non commercial environment.
• Follow battery usage, storage, and charging guidelines found in the user's
guide.
• Improper battery use may result in a fire, explosion, or other hazard.
• To charge the mobile device battery, the battery and charger temperatures
must be between -4ºF and +122 ºF (- 20 ºC and +50 ºC)
• Do not use incompatible batteries and chargers. Use of an incompatible
battery or charger may present a risk of fire, explosion, leakage, or other
hazard. If you have any questions about the compatibility of a battery or a
charger, contact Zebra support.
• For devices that utilize a USB port as a charging source, the device shall only
be connected to products that bear the USB-IF logo or have completed the
USB-IF compliance program.
• Do not disassemble or open, crush, bend or deform, puncture, or shred.
• Severe impact from dropping any battery-operated device on a hard surface
could cause the battery to overheat.
Do not short circuit a battery or allow metallic or conductive objects to contact
the battery terminals.