MOUNTAIN ALARM XL 4600 User manual

MOUNTAIN ALARM
DIV. OF J.D DAVIS COMPANY, INC.
1235 S. HURON STREET
DENVER, CO 80223
Congratulations on you n w alarm d t ction syst m. Th syst m is v ry simpl to op rat .
Mountain Alarm has tri d to anticipat som of your qu stions. Th following op rating instructions will
h lp you familiariz yours lf with th XL 4600 System.
1. 4.
2. 5.
3. 6.
A. KEYPAD OPERATION:
1. ZONE LIGHTS (ZONES 1-6):
Zon Normal ------------------------------------ Light Off
Zon Op n -------------------------------------- Light On
Zon Bypass d -------------------------------- Slow Blink
Zon Alarm ------------------------------------- Fast Blink
2. STATUS LIGHTS:
RDY: -------------------------------------- ON- Syst m R ady to b arm d.
OFF- Syst m not r ady to b arm d.
ARM: -------------------------------------- ON- Syst m is arm d.
OFF- Syst m is off.
STAY: ------------------------------------ ON- Int rior zon s ar bypass d.
OFF- Int rior zon s ar normal.
INST.: ------------------------------------ ON- Entry doors ar instant.
OFF- Entry doors ar d lay.
AC/LB: ----------------------------------- ON- AC pow r is pr s nt.
OFF- AC pow r is off.
NOTE: 1. A blinking “AC/LB” lig t & blinking keypad is a trouble signal and it
indicates low battery. To silence enter your code at t e Keypad.
B. SYSTEM OPERATION:
1. ARMING THE SYSTEM (L aving Hom ): 1. Ent r your four digit cod .
2. Pr ss “#” & 1 to quick arm OR
3. Pr ss “#” & “2” to forc arm.
NOTE: 1. T ere is a time delay on t e entry/exit doors.
2. You must leave wit in 60 seconds.
2. ARMING THE SYSTEM (Staying Hom ):--1. Pr ss th “STAY” K y.
2. Ent r your four digit cod .
3. DISARMING THE SYSTEM: ----------------- 1. Ent r your four digit cod .
NOTE: 1. T ere is a time delay on t e entry/exit doors.
2. T ere is a steady tone upon re-entering. It will not stop until t e system is disarmed.
3. T e system must be disarmed wit in 20 seconds, or t e siren will come on.

4. TO MAKE ZONE-1 INSTANT: ---------------------------------1. Pr ss “INSTANT” button.
2. Pr ss “STAY” button.
3.Ent r your four digit cod .
NOTE: Disarming automatically reactivates t e time delay.
5. TO BYPASS ANY ZONE: -----------1. Syst m must b disarm d.
2. Pr ss “BYPASS” button.
3. Ent r your four digit cod .
4. Pr ss th zon numb r of th zon to b bypass d.
5. R p at st ps 2, 3, & 4 to r mov a bypass d zon .
NOTE: Once armed, disarming automatically removes bypass.
C. PANIC BUTTONS:
1. TO OPERATE PANIC: --------------1. Pr ss “*” and “#” k ys simultan ously.
2. Ent r your cod to sil nc th sir n.
D. FIRE SYSTEMS:
1. Th fir syst m is activat d automatically.
2. Pr ss “7” and “9” to manually activat th syst m.
3. If th smok d t ctors ar s t off accid ntally, nt r your cod to sil nc th m.
E. W AT TO DO IF T ERE IS A FALSE ALARM:
1. Burglar Alarm: A) Stay calm and go to th n ar st k ypad. Ent r your cod to sil nc th sir n.
B) Onc th alarm has gon off, you must nt r your cod a s cond tim to
ras th alarm m mory and r s t th syst m. Th syst m cannot b arm d
again until this is don .
2. Panic Alarm: Ent r your cod to sil nc th sir n.
3. Fir Alarm: Ent r your cod to sil nc th sir n.
4. If th monitoring company calls, giv th m your nam and abort cod .
F. PROGRAMMING ARM/DISARM CODES:
NOTE: A) T e system must be disarmed, it doesn’t matter if a zone is opened.
B) A total of 6 user codes may be selected.
C) Eac code contains 4 numbers.
1. STEPS: 1. Pr ss th “CODE” k y.
2. Ent r th us r 1 cod (mast r cod ).
3. Ent r th us r numb r of th cod to b chang d or d l t d. (1 through 6)
A) Ent r 4 digits to mak a n w us r cod .
B) Pr ss “*” to d l t and xisting us r cod .
4. N xt, arm/disarm th syst m with th n w cod to mak sur it works. If th syst m
can b arm d/disarm d with th n w cod th n you did it corr ctly and you ar
don .
If you hav any qu stions, pl as call 303-698-2330.