Mountup MU0004 User manual

Single Monitor Counterbalance Desk Mount
Instruction Manual
If you have any questions , please contact us via: [email protected]
75x75
100x100
2~8kg
4.4~17.6lbs
32"
MU0004
V6.0

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of
this product, contact Customer Service via [email protected].
Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
NOTE: Not all hardware included will be used.
DO NOT EXCEED WEIGHT CAPACITY.
WARNING!
PACKAGE CONTENTS
17.6lbs
(8kg)
A (x1)
Arm
C (x1)
Bracket
D (x1)
Clamp
F (x1)
Grommet Base
G (x1)
Wingnut
I (x1)
Bolt
H (x1)
Carriage Bolt
J (x1)
Support Plate
K(x1)
4mm Allen Key
L(x1)
5mm Allen Key
M(x1)
6mm Allen Key
E(x5)
M6x10
B (x1)
VESA Plate
M-C (x4)
D6 Washer
M-A (x4)
M4x12
M-B (x4)
M6x12
01
M-D (x4)
spacer

OPTION A: Clamp Installation
Mount bracket (C) to bottom of gas spring arm (A) using bolts (E). Tighten using 4mm allen key (K).
Attach clamp (D) to bracket (C) using bolts (E) and 4mm allen key (K). Mount according to thickness of desktop.
Secure stand to desktop by tightening clamp (D) or by using 6mm allen key (M).
ASSEMBLY STEPS
STEP 1: Clamp Installation OR Grommet Base Installation
D
E
KK
E
10-60mm
10-90mm
D
M
OR
OR
02
C C
D
E
K
A
C

OPTION B: Grommet Base Installation
For grommet hole mounting, place carriage bolt (H) through the center of grommet base (F). Mount grommet
base to bottom of gas spring arm (A) using bolts (E). Tighten using 4mm allen key (K). Run carriage bolt (H)
through grommet hole in desktop. Attach metal plate (J) and wingnut (G). Tighten wingnut.
STEP 1: (Continued)
G
H
J
03
K
F
E
H
A

STEP 2: Attach Monitor
B
B
M-A
M-B
M-C
M
04
M-A
M-B
M-C
M-D
M
OPTION A: Flat Back Monitor
Attach the VESA plate (B) to back of monitor and
secure with screws(M-A)or(M-B) with washers(M-C)
using 6 mm Allen Key (M). Avoid excessive
tightening screws damage the monitor.
CAUTION:To select the correct screws(M-A or M-B)
for your monitor, you can try to screw it on your
monitor by hand. The one can screw inside is the
correct screw for your monitor.
OPTION B: Curved Back Monitor
Attach the VESA plate (B) to back of monitor and secure
with screws (M-A) or (M-B) with washers (M-C)and
spacers(M-D)using 6 mm Allen Key (M). Avoid excessive
tightening screws damage the monitor.

Slide the monitor onto the head of swivel arm, install the security bolt (I). Make sure the security
bolt is installed before you rotate the monitor.
STEP 3: Hang Monitor
Refer to below illustrations to
adjust tilting angle of your monitor.
05
I
Note: Fasten/loosen the tilting bolt
as needed per arrow direction (+/-)
shown in above diagram.
L
L

STEP 4: Adjust Tension
For proper functioning of this mount, depending on dierent weight of monitor you might need to adjust
tension in gas spring arm (A) using 5 mm allen key (L).
06
L
A
If necessary, refer to above illustrations
to adjust the level of tightness of the
arms.
CAUTION
After being attached to the arm, the monitor falls down
and can not stay at the desired height by itself.
Turn counter-clockwise(“+”direction) to increase gas
spring tension until the monitor can stay at the desired
Height by itself.
After being attached to the arm, the monitor rises up and
can not stay at the desired height by itself.
Turn clockwise(“-”direction) to reduce gas spring tension
until the monitor can stay at the desired Height by itself.
Note：
Be sure to keep the arm in horizontal
position during adjustment. Or else it
would be dicult to adjust the mount
or damage the mount.
+
-
L

STEP 5: Cable Management
07
A
Remove bottom plastic covers from gas spring arm(A) as shown in diagram.

STEP 5: (Continued)
08
Run cables from monitor through bottom of gas spring arm (A). Reattach plastic covers as shown in diagram.

Adjust as Desired
09
DESK DESK
Pay attention while clamp install !
Note: When tilted, if the monitor sags or does not stay,
please fasten the tilting bolt on the mount until the
monitor can be held at any angle as needed.
360°
360°
360°
+90°
-45°
180°

Product Dimensions
STEP 6
-45°
+90°
180°
360°
0.39-3.3"
3.9"
6.3“ 7.2"-10.2" 1.96"
6.7"-16.1"
2.9”
3.9“
4.5“
2.9” 3.9“ 4.5“
10
9.8"

CAUTION AND MAINTENANCE:
• Never allow children to climb, stand, hang, or play on any part of monitor or stand.
• This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
If you have any questions, please contact us.
[email protected]