Mountup MU0002 User manual

Dual Monitor Desk Mount
Instruction Manual
If you have any questions , please contact us via: [email protected]
MU0002
V2.0
75x75
100x100
(8kg/17.6lbs)x2
27"

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of
this product, contact Customer Service via [email protected].
Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
NOTE: Not all hardware included will be used.
DO NOT EXCEED WEIGHT CAPACITY.
WARNING!
PACKAGE CONTENTS
(17.6lbs)x2
(8kg)x2
B (x1)
Swivel Arm
C (x1)
Clamp
D (x1)
Pole
G (x3)
Bolt
F (x1)
Base Plate
L(x1)
4mm Allen Key
H(x1)
Support Plate
M(x1)
6mm Allen Key
J(x2)
Plastic Cover
K(x2)
Bolt
I(x4)
Wire clip
E(x1)
Wire Clip
A (x2)
VESA Plate
M-E(x8)
D6 Washer
M-A (x8)
M4x12
M-B (x8)
M4x16
M-C (x8)
M6x12
M-D (x8)
M6x16
01
M-F (x8)
Spacer

OPTION A: Clamp Installation
Install the Clamp (C) to the Pole (D) using 3pcs Bolt(G). Tighten using 4mm Allen key (L).
Secure stand to the desktop by tightening the plastic knob or by using 6mm Allen key (M).
ASSEMBLY STEPS
STEP 1: Clamp Installation OR Grommet Base Installation
02
G
L
10-80mm
M
OR
D
C

STEP 1: (Continued)
03
OPTION B: Grommet Base Installation
If existing grommet hole comes with a plastic protector, remove it to ensure a at surface before installing
the desk mount.
Loosen the screw, separate the C-clamp (C) into two parts.
Install the Grommet Base Plate (F) to the Pole using 1pc Bolt (G). Position pole (D) on the mounting surface
and secure using the support plate (H) and the bolt separated from clamp. Secure the pole to the desktop
by tightening the plastic knob or by using 6mm Allen key (M).
10-80mm
D
F
H
G
M
OR
DESK
DESK
ø 0.39"~3.1"
C

STEP 2 : Arm Installation
04
Install wire clip (E) and swivel arm (B) to the pole (D). Fasten the bolt with supplied 6mm Allen key (M).
Attached the wire clips (I) to the swivel arm (B).
E
I
D
M
B

05
CAUTION:To select the correct screws (M-A or M-C)
for your monitor, you can try to screw it on your
monitor by hand. The one can screw inside is the
correct screw for your monitor.
STEP 3 : Attached Monitor
A
A
M-A
M-C
M-E
M
M-B
M-D
M-E
M-F
M
OPTION A: Flat Back Monitor
For flat back monitor, secure VESA plate (A) to monitor
using screws (M-A or M-C) and washers (M-E). Tighten
the screws using 6mm Allen key (M).
OPTION B: Curved Back Monitor
For monitor with curved or recessed back, align spacers (M-F)
with mounting holes in monitor, and secure VESA plate (A) to
monitor using screws (M-B or M-D) and washers (M-E). Tighten
the screws using 6mm Allen key (M).

STEP 4 : Hang Monitor
Slide the monitor onto the head of swivel arm (B). Install the plastic cover (J) and security bolt (K).
Tighten the bolt with the supplied 4mm Allen key (L). Make sure the security bolt (K) is installed
before you rotate the monitor.
06
K
L
J
B
B

STEP 5: Tilt Adjustment
Tighten the bolt with the supplied 6mm Allen key (M) to x the tilt angle.
07
M
M
Refer to below illustrations to
adjust tilting angle of your monitor.
Note: Fasten/loosen the tilting bolt
as needed per arrow direction (+/-)
shown in above diagram.

STEP 6: Cable Management
Manage cables and store Allen keys (L,M) in wire clip (E) for future use.
08
L
M
E

Adjust as Desired
Adjust monitor position and rotation.
For minor height adjustment, turn the plastic cover (J) with the supplied 6mm Allen Key (M) to raise or lower
the monitor. Ignore this step if the two monitors are level.
09
Note: When tilted, if the monitor sags or does not stay,
please fasten the tilting bolt on the mount until the
monitor can be held at any angle as needed.
+90°
-90°
+90°
-90°
360°
360°
M
J
DESK

10
Product Dimensions
114mm
100mm
75mm
75mm
100mm
114mm
135mm
5.3“
38mm
1.5"
185mm
7.3“
±90° ±90°
±90°
±90°
±180°
403mm/15.8"
105mm/4.13"
2.9”
3.9“
4.48“
2.9”
3.9“
4.48“
00mm~80mm
0“-3.15”

CAUTION AND MAINTENANCE:
• Never allow children to climb, stand, hang, or play on any part of monitor or stand.
• This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
If you have any questions, please contact us.
[email protected]