Panasonic ET-RFD32 User manual

Important safety notice
Product description
Assembly procedure
Installing the projector in the frame
Installing tandem projections
Maximum stacking information
Adjustment options
Dimensions
ET-RFD32
INSTALLATION MANUAL
2
3
4
4
5
5
6
7
Only a qualied installer should install this product.
Read these instructions carefully before installing the ET-RFD32 projector frame.
These installation instructions must always be handed over to the installing person.
For projectors:
PT-RZ31K / PT-RS30K / PT-RQ32K & weight

IMPORTANT SAFETY NOTICE
Dear customer,
Thank you for choosing the ET-RFD32 frame for Panasonic DLP® based projectors.
This instruction booklet provides you with all the necessary operating information that you may
require. It will help you to get the best performance out of this new product. We hope you
will be pleased with your Panasonic projector frame.
Model number: ET-RFD32
SAFETY PRECAUTIONS
This frame is DGUV V17 (BGV-C1) certied. Please consider the valid laws at the place of event.
WARNING
Installation work should only be carried out by a qualied technician.
- If this product is not installed correctly, serious accidents may result.
Do not place the projector on top of unstable surfaces.
-If the projector is placed on top of a surface which is sloped or unstable, it may fall down or tip over
and injury or damage could result.
Make sure not exceed max. weight loads for ceiling mounts.
- For suspended installations, use only designated hanging accessories,
like TH-SHORTY-350-8/10 for a max. weight load of 350 kg ( 771,62 lbs).
CAUTION
Do not install the frame in a place which may impede projector ventilation.
-If this is not observed, re may result.
Do not set up the projector in humid or dusty places or in places where the projector may
come into contact with oily smoke or steam.
-Using the projector under such conditions may result in re, electric shocks or plastic deterioration.
Minimum 2 people are required to install the frame.
-With regard to the overall weight of all neccessary installation devices, make sure to handle those
with at least two people.
2.

PRODUCT DESCRIPTION
Frame Used for projector
installation.
Screws and
washers
Used for securing the
projector into the frame.
Flat washers (M10) x 12
max. 2 mm
Screws (M10x35) x 6
Purpose Finished assembly diagramImage/DrawingPart name
3.
Another separate
frame is required
for tandem assemblies.

4.
Place the frame on the projector so that it is
aligned with the screw hole positions.
(Make sure that the forward/back direction is
correct when installing. If the direction is reversed,
the hole positions will not match up.)
Secure the projector to the frame using the six
screws (M10x35) and the twelve at washers (M10).
Do not forget to use the washers as they are
responsible for the galvanic isolation.
Torque: 20 ± 1 Nm
INSTALLING THE PROJECTOR IN THE FRAME
screw (M10x35)
at washers (M10)
Please make sure to use ONLY the
correspondent screw holes when
installing a projector!
Before installing of the frame,
remove the handles on the front and
the back of the projector.

5.
ceiling mount with
TH-SHORTY-350-8/10
Frame ET-RFD32
table mount
INSTALLING TANDEM PROJECTIONS
Place the upper projector with frame on top
of the lower projector also in frame. Make sure the four male
location bolts enter into the correspondent female
location bolts. To secure, draw the locking pin through
both bolts.
locking pin
male bolt
female bolt
MAXIMUM STACKING INFORMATION

6.
Using the adjusting screws to the left and
right you can adjust the position of the
projector by approximately three degrees.
You can lower or lift the front left or right corner.
adjusting screws
By turning the single round adjustment screw,
placed on the side of the frame, you
can move the back of the projector
to the left or to the right by approximately
three degrees.
single
adjustment
screw
ADJUSTMENT OPTIONS


 
 
 



 



 

DIMENSIONS & WEIGHT
7.


 
 
 



 



 
Weight: 37,10kg

Made in Germany
for
by Sager Metallbearbeitung
www.lang-ag.com
03/17


 
 
 



 



 