Movincool Climate Pro K36 User manual

1
If the parts appear to be damaged or missing, contact your MovinCool dealer.
PUMP INSTALLATION
Model Name Climate Pro K36
Part No. (voltage) 484789-0240 (208/230V)
Condensate Pump Kit Installation Manual
484007-5010
WARNING
Disconnect power before installation. Beware that some residual voltage may remain in the
unit after the power is disconnected. There is a risk of electric shock.
1. Open the drain tank cover and remove the tanks from the unit.
Outlet Hose (1)
20  (6.0 m), Φ3/8 in (9.5 mm)
M4 × L10
Screw w/Washer (2)
2  (0.6 m), Φ1/2 in (12 mm)
Drain Inlet Hose (1)
Hose Clamp (1)
Condensate Pump (1)
3. Punch out the knock-o hole in the lower service panel using a tool such as a screwdriver. This
hole is used to pass through the outlet hose.
2. Loosen the two (2) screws at boom edge and remove the other four (4) screws. Pull the lower
service panel upward and remove it from the side panel.
Loosen screws (2)
Take out screws (4)
Lower Service Panel
Knock-o Hole

2
3. Remove the five (5) screws from the condenser
side panel.
Screw (5)
Condenser Side Panel
4. Remove the tab and cap as shown from the
condensate pump.
5. Place the condensate pump into the unit from
the front as shown.
Condensate Pump
REMOVE
Tab
Cap
6. Disconnect the mating connector from the jumper
plug by pressing the tab as shown.
Jumper Plug
Mating Connector
Tab
Mating Connector with Jumper Plug

3
7. Connect the pump connector to the mating
connector.
6. Secure the five (5) screws on the condenser side panel, which were removed in procedure 3 on
page 2.
10. Secure the pump to the adapter plate.
Detailed procedure is as follows:
a) Insert the two (2) screws into the upper
holes of the adapter plate.
b) Slide the mounting slots of the pump over
the screws.
c) Secure the screws.
HOSE INSTALLATION
1. Pass the hose clamp through the inlet hose. Connect one end of the inlet hose to the drain stem
of the unit and secure with the hose clamp by removing the tab as shown.
2. Pass the other end of the inlet hose through the hole as shown and insert it into the pump inlet.
3. Unwind the outlet hose and connect to the drain outlet spout of the pump.
4. Pass the other end of the outlet hose through the knock-out hole in the lower service panel.
5. Reinstall the lower service panel to the unit.
Outlet Hose
Inlet Hose
Drain Stem
Pump Inlet
Outlet Spout
Hose Clamp
Remove Tab
Adapter Plate
Mounting Slot
Screws
(
2
)
Mounting Slot
Pump Connector Mating Connector

4
Voltage Max. height for liing
230 VAC 17 feet (5.2 m)
208 VAC 13 feet (4.0 m)
When hanging the hose from the ceiling, the maximum height for liing the hose vertically depends
on the voltage that the unit uses.
Check the maximum hose height in the table below. Run the drain hose on a downward slope at a
minimum rate of 1/4 inch(6.25mm) per foot.
TESTING
1. Turn the unit on.
2. Take out the end of the inlet hose from the inlet hole.
3. Pour water into the pump reservoir from the inlet hole.
4. Make sure that the pump starts running and water is drained through the outlet hose.
5. Reinsert the end of the inlet hose into the inlet hole.
CAUTION
Ensure smooth drainage through the hose. If the hose is kinked or clogged, it may cause
malfunction and property damage due to water leaks.
Max. Height for Liing
Outlet Hose
1/4 inch taper per foot