MPM RAPID mini User manual

User Manual
RAPID mini precision grinder
E106015.docx
ED: 16.01.17
SD: 02.12.19
Dieter Marx
- 1/2 -
Micro Präzision Marx GmbH D-91056 Erlangen 09131-9056-0 09131-9056-600
Applications:
Cylindrical grinding --- taper grinding --- form grinding ---
polygon grinding --- plunge-cut grinding --- smallest diameter grinding
On your surface grinding machines!
Mode of use
1. Set the RAPID mini on the magnetic table of the surface grinder. Adjust the right-angled
groundplate to the stop ledge of the magnetic table and switch the magnet on.
2. Place the workpiece under the centre of the grinding wheel.
3. Select with or the sense of rotation and spindle start.
4. Determine the highest point of the workpiece by moving the machine-table.
5. When grinding cylindrical and taper parts, the timing belt must be tightened and the index bolt
must be unlocked!
Switch the motor on and let the workpiece rotate.
6. When grinding surfaces or polygons, the timing belt must be loosened.
For this, the clamping screw for the motor bracket must be released.This screw is on the
bottom of the block. Then you can move the motor along the slot.
7. The motor must be switched off and the index bolt must be locked.
Observe safety
instructions:
IN SLEWED POSITION
ONLY GRIND TOWARDS
THE GAUGE BLOCK !
NEVER REMOVE THE
TIMING BELT COVER WHEN
MACHINE IS IN OPERATION
Maintenance:
The RAPID mini grinder is sealed on the front and rear side with a shaft-sealing ring for
splash-water protection.
In case of heavy coolant use we recommend an additonal cover.
Cleanness and good care preserve the precision of the RAPID mini grinder .

User Manual
RAPID mini precision grinder
E106015.docx
ED: 16.01.17
SD: 02.12.19
Dieter Marx
- 2/2 -
Micro Präzision Marx GmbH D-91056 Erlangen 09131-9056-0 09131-9056-600
Taper grinding:
Slewable up to 45° (relative 90°). Use gauge block according attached sine table.
Up to +45° angle position place the gauge block underneath the front sine axle.
When minus degrees are necessary, position the gauge block underneath the rear sine axle.
At an angle +90°, adjust both sine axles vertically.
Grinding with tailstock and rigid center punch:
Please observe heat development, thin workpieces may bend.
Motor-temperatures up to ca. 60° are harmless.
Workpiece change:
Lock the spindle with the index bolt. Loosen, respectively tighten the collet chuck with the hook
spanner.
The spindle cone (toolholder) is suitable for collets Ø-range 2-20mm.
High precision collets, reduction sleeve ER11, reduction sleeve DECKEL S20, three-jaw chuck
Ø80mm, magnet chuck Ø60 and Ø100mm are optional.
1. Connect mains supply and 5-pole lead. The device is on.
2. The OFF button is illuminated.
3. Select the sense of rotation. Right with , left with 
4. The active rotation button is illuminated
5. With the potentiometer is the spindle speed adjustable up to ca. 300min-1
6. Stop the spindle rotation with OFF
Technical details:
Ground plate ca.
125x100mm
Weight ca.
9 kg
Height (horizontal) ca.
110mm
Index-divider
15°
Height (vertical) ca.
175mm
Centre height ca.
45mm
Toolholder
E32
(for collets Ø 2-20mm)
Spindle true running
0,002mm
Drive
E-Motor,
continiously adjustable
up to 300min-1
sense of rotation selectable
Mains supply
115-230V
50-60Hz
70W
Subject to change without prior notice.,

MPM
Rotation left 
Rotation right 
The OFFbutton
illuminates after
mains connection.
It must be actvated
at every change of
direction (left/right)!
Potentiometer for
speed regulation
Connection
line voltage
Cable connection
grinding device
Please compare set voltage on the main switch with your line voltage.