Mr. Beams MB371 Manual

Thank you for purchasing the Mr. Beams™ Remote
Control and Motion Sensor Spotlight. We are
committed to eliminating darkness by using the
latest in light-emitting diodes (LED’s). LED’s are
the most efficient and durable light sources avail-
able. We are certain that your Mr. Beams Spotlight
will contribute to a safer environment and provide
light where you need it at a very reasonable cost.
ENCLOSED YOU WILL FIND:
x Remote-Controlled and Motion-Sensor
Spotlight with Mounting Base
x Remote Control with Mounting Bracket
x (2) 3V Coin Cell Batteries
x 3 Screws and 2 Anchors
Remote Control & Motion-Sensor Spotlight – Item MB371
INSTRUCTION GUIDE
MB371 SPOTLIGHT FEATURES
Remote Control—Turn Spotlight On and
Off from up to 70ft away.
Note: Remote Control will not override mo-
tion or light sensor or auto shut-off.
Motion Sensor Activated – You can set the
on-time of the light at 30 seconds or 10 min-
utes. Light shuts off automatically if no
motion is detected.
Light Sensor – Motion-Sensor Spotlight
goes on only in darkness to conserve battery
life.
Mount to Wall – Motion-Sensor Spotlight
can be rotated 360° as well as up and down.
WARNING
x Use only new alkaline D-Cell batteries
with 1.5V rating. Do not mix old and
new batteries. Install batteries with
polarity in correct position.
x Follow battery instructions for proper
disposal and cautions.
x Mount fixture securely with included
screws, and use anchors if not securing
to solid wood or other solid material.
Use the third screw if mounting Spot-
light upside down!
x Black wire inside unit is the antenna,
do not attempt to attach or remove
(one end is attached, one is loose).
1. Remove front cover of
Spotlight by rotating
counter-clockwise as shown
in Illustration 1a to reveal
controls and battery holders.
Insert 3 D-Cell Batteries
into Spotlight as shown in
Illustration 2. Flat side of
batteries match springs.
2. Set your automatic
shut-off time to Min or
Max (Illustration 3a).
NOTE: Light will stay on
as long as motion is detected. We recommend
Min to save battery life.
IMPORTANT NOTES:
x RF Spotlight has a black wire antenna inside with one side attached to unit. Please
be sure to carefully wrap or tuck the antenna before twisting unit shut. If antenna
wire is damaged, the remote will no longer activate it.
x Please use only new alkaline D-Cell batteries with 1.5V rating.
x Do not mix old and new batteries.
x If your light stays on constantly, it’s time to change the batteries!
x Do not mount remote on metal as it interferes with signal
x You must hold down button on remote for one second to control light
x Spotlight only activates in darkness to conserve batteries. Test in a dark room or closet before installing.
INSTALLATION INSTRUCTIONS
Mr. Beams
32111 Aurora Road, #8
Solon, OH 44139
877.298.9082
www.mrbeams.com
Motion
Sensor
LED
Light
Mounting
Base
Mounting
Base Thumb
Illustration 2
Min Max
30 sec. 10 min.
4. Open the Remote Control and con-
firm that the code matches the code set
on the Spotlight (Illustration 4).
5. Insert 2 (Two) flat 3V batteries
(included) as shown on the inside of the
Remote Control. Smooth side of battery
should be facing up.
6. Match arrows then turn cover clock-
wise (Illustration 5). Make sure unit
is securely closed with arrow pointing
past the lock symbol to ensure weath-
erproof seal is tight.
BEFORE YOU MOUNT YOUR SPOTLIGHT
Illustration 1a Illustration 3a Illustration 5
Illustration 1b Illustration 3b Illustration 4
SPOTLIGHT REMOTE

LIMITED WARRANTY
The product you have purchased is guaranteed against defects in workmanship and materials for the period stated on the package. Warranties implied by
law are subject to the same time period limitation. Some states do not allow limitations on how long an implied warranty lasts, so this time limitation may
not apply to you. If the product fails due to a manufacturing defect during normal use, return the product and dated sales receipt to the store where pur-
chased for replacement OR send the product and the dated sales receipt to the address above. Not Covered – Batteries are not covered by this warranty.
Repair service, adjustment and calibration due to misuse, abuse or negligence are not covered by this warranty. Unauthorized service or modification to this
product or of any furnished components will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation,
set-up time, loss of use, postage, unauthorized service, or other products used in conjunction with, but are not supplied by, Wireless Environment.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
MOUNTING YOUR REMOTE CONTROL
Illustration 12
Determine placement for bracket and attach
to wall using two screws (enclosed) or tape
as shown in Illustration 12.
Illustration 13
Slide Remote into Bracket as Shown
in Illustration 13
MOUNTING YOUR SPOTLIGHT TO WALL
Determine location for mounting Spotlight.
NOTE: FOR BEST PERFORMANCE, SPOT-
LIGHT SHOULD BE POSITIONED SO MO-
TION SENSOR IS ON TOP AND LIGHT IS
ON BOTTOM. The simplest way to attach
your Spotlight to a tree or wall is to drive the
large screw through the center of the mounting
base. First, loosen thumbscrew on mounting
base and separate the mounting base from the
rest of the light as shown in Illustration 6.
Drive large screw through center hole of the
mounting base as shown in Illustration 7.
For a more secure attachment, first use the two
smaller screws as follows: Use template
(above) to mark two holes for anchors and/or
screws (included) as shown in Illustration 8.
NOTE: Spotlight can be rotated 360°, so screws
can be mounted in any position. We recom-
mend mounting the screws parallel to the
ground if mounting on a vertical surface. Make
sure that screws are precise distance from each
other as configured in template (2-1/8” apart).
Attach Mounting Base to screws as shown in
Illustration 9. Slide Mounting Base down so
screws are securely held by track. If using an-
chors, use 3/16” drill bit to drill holes and insert
anchors. Drive screws into anchors so that
screw head protrudes 1/8” from surface (the
height of the screw head). If using screws only,
use 1/8” drill bit to drill holes and insert screws
so that screw head protrudes 1/8” from surface
To attach Spotlight to Mounting Base, align holes
then insert and tighten thumb screw (Illustration
6). To adjust Spotlight direction, loosen smaller
thumbscrew on Mounting Base and rotate Spotlight
to proper direction as shown in Illustration 10.
Tighten thumbscrew.
Loosen larger thumbscrew that connects Spotlight
Head to Mounting Base and adjust Spotlight Head
to proper direction as shown in Illustration 11.
Tighten thumbscrew.
Illustration 8 Illustration 9
Illustration 10 Illustration 11
2-1/8”
Use These Holes for Template
Screws Tape Placement
Note: Hold down On and Off buttons for
one second to control light.
Illustration 6 Illustration 7
For More Installation and Use Advice, Along with More Wireless Lighting Products, go to www.mrbeams.com