MRdirect 701 User manual

Installation Guide 1
Model 701
Single-Handle Bathroom Faucet
Tools
Certications & Information
Configuration
Installation Guide
Gather the necessary tools as shown to complete the installation of this faucet.
Connect to water supply lines with TWO
3/8" Compression Faucet Connectors
The following tools are optional:
FlashlightSafety Glasses Channel Lock
Adjustable Wrench
Pliers
3
GPM Flow Rate Chart
PSI
2
0010 20 30 40 50 60 70 80
2.5
1.5
Faucet
Sir
1 1/4"
4" 2"
1 1/4" 1 1/4"
Water
supply
Connector
• NSF Certified
• cUPC & UPC
• ADA Approved
• Limited Lifetime Warranty
• Lead Free Construction
• WaterSense Certified
Three-Hole Installation
4" Centerset
* This measurement is only suggestive and may vary
according to the sink model.

2
Installation Guide
Faucet Installation
E
G
C
F
A
A. Turn o the water supply. Remove the
faucet with the mounting hardware
attached from the package.
B. Remove all mounting hardware from
the shanks.
D
B
C. Insert the shanks of the faucet body into
the holes of the sink deck.
D. From the underside of the sink or
mounting surface, attach the washer,
followed by the lock nut, onto the shank.
Repeat this for the second shank.
E. Hand-tighten the lock nut until secure.
F. Attach a 3/8" compression faucet
connector to the end of each shank.
G. Attach the opposite end of each hose
to the corresponding water supply lines
by tightening the 3/8" compression ttings
onto the lines. Secure all ttings with a 1/4
turn of a wrench.
shank washer
lock nut
sink deck

3
Installation Guide
Remove the aerator from the end of the faucet by carefully unscrewing it.
Let hot and cold water run through both water lines for at least one minute
before replacing the aerator. This will help to clear any debris in the line,
which could otherwise clog the system.
Important
Pop-Up Drain Installation
A. Remove pop-up drain stopper (6), and ange (7) with top
rubber washer (8) from the pop-up assembly.
B. Insert drain body (9) from underneath of sink drain hole.
Replace ange (7) and top rubber washer (8) back to drain
body (9). Tighten ange securely.
C. Slide the bottom rubber washer (10) back on the drain pipe,
up to and against the bottom of the sink. Tighten the washer
(11) and the lock nut (12) rmly against the base to form a
tight seal.
D. Replace pop-up drain stopper (6) into the drain body (9)
with o-ring (10) in place, and align the hole in the stopper
with the guide rod opening.
E. Remove the rod guide nut (11) and rod ball rubber gasket (12).
F. Insert rod ball assembly (13) into the drain body (9)
and through the hole in the drain stopper (14).
G. Replace the rod guide nut (11) and the rod ball
rubber gasket (12) and tighten securely.
H. Insert pop-up stem (15) through the hole in the faucet
body (16). Connect rod ball assembly (13) to the lift rod (18)
using the spring clip (17) to hold and adjust.
I. Attach the lift rod (18) to the pop-up stem (15) by inserting
the stem through the hole in the lift rod (20). Then, adjust the
pop-up stem (15) to the correct height and hand-tighten the
lift rod screw (19).
7
8
11
12
10
6
10
9
15
16
19
18
20
17
13
11
12
14
13
7
9
To prevent damage to the tube body, tighten the connections by carefully using two
wrenches as shown. Use caution to not bend the stem.
Check for leaks.
Turn on the water supply SLOWLY, to test for leaks
before completely opening the water lines.

Installation Guide 4
Maintenance & Cleaning
Notes
The faucet can be cleaned by rinsing with clear water or washing with mild detergents. Dry the faucet with a clean, soft cotton cloth.
CAUTION: do not use any cleaning agents containing acids, abrasives, or other harsh chemicals.
Simply rinse and dry faucets with a soft towel every week to prevent
mineral deposits from forming. Clean spills and splatters as they happen.
Do not let soap, toothpaste or other contaminates dry on the faucet, this
can stain or pit the nish. Use a mild soap and soft sponge or towel to
remove residue. Rinse and dry thoroughly.
Never use an abrasive cleaner or rough sponge to clean or dry your
faucet. Harsh cleaners could dull or scratch the nish. Use only a soft
disinfectant that does not contain bleach or chlorine and apply with a
soft towel.
www.mrdirectint.com
[email protected]
1-877-946-5725
Warranty Information
MR Direct warrants to the original consumer purchaser that our sinks and faucets will be free from defects in
material and workmanship under normal use for the lifetime of the product. MR Direct may elect to repair or
replace any defective MR Direct product covered by our warranty.
Our warranty does not cover defects caused by misuse, abuse, negligence, alterations, environmental conditions,
improper installation, storage and handling; nor any labor expenses.
From time to time we will change design specications and materials as conditions require and improvements
are developed. We have no obligation to incorporate such changes in products we previously manufactured.
This warranty is in lieu of any and all other warranties, express or implied, including any warranties of
merchantability and of tness for a particular purpose; and excludes any incidental or consequential damages.
No representative has the authority to change or enlarge the above warranty.
This warranty is only valid in the United States of America. Some states do not allow limitations on how long
an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusion may not apply. This warranty gives you specic legal rights, and you may also have other
rights which vary from state to state.
One-Year Accessory Warranty
MR Direct warrants to the original purchaser that all of our accessories will be free from defects in material and
workmanship under normal use for one full year.
Our warranty does not cover defects caused by misuse, abuse, negligence, alterations, environmental conditions,
improper installation, storage and handling; nor any labor expenses. MR Direct may elect to repair or replace any
defective MR Direct accessory covered by our warranty.