MSE PSE-608R User manual

USER’S MANUAL
PSE-608R(I)/616R(I)/624R
Power Source Equipment

User’s Manual PSE-608R(I)/616R(I)/624R
2
Contents
1. Introduction...........................................................................
Features................................................................................................
Package Contents.................................................................................
2. Hardware Description...........................................................
Physical Dimension...............................................................................
Front Panel............................................................................................
LED Indicators.......................................................................................
Rear Panel............................................................................................
Power On..............................................................................................
Network A lication...............................................................................
RJ-45 Remote Control Port...................................................................
3. Software Utility Installation..................................................
4. GUI Management...................................................................
Dis lay and Illustration..........................................................................
System Login........................................................................................
Modify Password…...............................................................................
Edit Station TCP/IP...............................................................................
Edit Remote PoE IP.............................................................................
GUI Connect All....................................................................................
Single Station Connect/Disconnect……………………………………..
Station and Status Window Select …...................................................
Edit Port Name…………………………………………………………….
Configuration.........................................................................................
Factory Setting…………........................................................................
Board Status…………………………………………………………………
Port Status…………………………………………………………………...
GUI Version………………………………………………………………….
GUI Disconnect All…………..…………………………………………......
File O en and Save…………………………………………………………
. Technical Specification........................................................
3
3
4
4
4
4
5
5
6
6
7
14
1
15
16
17
18
20
21
23
24
25
26
27
29
30
31
32
33
34

User’s Manual PSE-608R(I)/616R(I)/624R
3
1. Introduction
The PSE-608R(I)/616R(I)/624R PoE midspan, support 8/16/24 ports respe tively in a
10/100/1000BaseTx Ethernet network, over TIA/EIA-568 Category 5/5e/6 abling. DC
operating power, for data terminal units, is fed over data pairs of the abling (4/5 and 7/8).
This allows greater flexibility in the lo ating of network devi es and signifi antly de reasing
installation osts in many ases.
The PSE-608R(I)/616R(I)/624R follows the IEEE 802.3af/IEEE 802.3at and is ompletely
ompatible with existing Ethernet swit hes and networked devi es. Normally powers PDs
(Powered Devi es) that are Power over Ethernet enabled or are equipped to re eive power
over Ethernet. The PSE tests whether a networked devi e is PoE- apable, power is never
transmitted unless a Powered Devi e is at other end of the able. It also ontinues to
monitor the hannel. If the Powered Devi e does not draw a minimum urrent, be ause it
has been unplugged or physi ally turned off, the PSE shuts down the power to that port.
Devi es that are not equipped to re eive power over Ethernet may require an external
splitter in order to be powered. Conta t Mstroni for su h a splitter.
Features
8/16/24 port Power Sour ing Equipment ( power over Ethernet Hub)
Support 8/16/24 ports full load, max. 35W/port
AC input (100-240 VAC, 50/60 Hz)
IEEE802.3af/IEEE 802.3at omplian e, Power over Ethernet Mid-Span mode
Remote power feeding of Ethernet terminals up to 100 meters
Auto dete t PD, and support manual dete t PD
Centralized power distribution for PoE powered Devi e (PD)
Independent overload and short- ir uit prote tion per hannel
Supports IEEE 802.3af/IEEE 802.3at non-standard devi e
Auto refresh port status and support Plug and Play feature for PD
Standard 19” or 23” ra k mountable
DIY upgrade from 8 port to 16/24 port available
Remote manage up to 24 units via TCP/IP proto ol
Isolated DC input available, an work with battery, non-interrupt performan e.

User’s Manual PSE-608R(I)/616R(I)/624R
4
Package Contents
Unpack the contents of the PSE-608R(I)/616R(I)/624R and ver fy them aga nst the
checkl st below.
PSE-608R(I)/616R(I)/624R x 1
Power Cord x 1
Bra ket x 2 ( for 19” ra k mounted)
CD-ROM x 1 (Software Utility + User Manual)
Compare the ontents of your PSE-608R(I)/616R(I)/624R pa kage with the standard
he klist above. If any item is missing or damaged, please onta t your lo al dealer for
servi e.
2. Hardware Description
This Se tion mainly des ribes the hardware of the PSE-608R(I)/616R(I)/624R and gives a
physi al and fun tional overview.
Physical Dimension
PSE-608/608RI/616R physi al dimension is: 430mm x 290mm x 44mm (Lx W x H),
PSE-616RI/624R is 430mm x 400mm x 44mm (1U, 19” or 23” Ra k mountable).
Front Panel
Figure 2-1. The Front panel of PSE-608R(I)/616R(I)/62 R
The Front Panel of the PSE-608R(I)/616R(I)/624R onsists of 8/16/24 x RJ-45 Ethernet
ports (data), 8/16/24 x RJ-45 PoE ports (data + power), 8/16/24 x LED port indi ators, one
LED power indi ator and one RJ-45 remote ontrol port (in lude one LED).

User’s Manual PSE-608R(I)/616R(I)/624R
5
LED Indicators
The LED Indi ators gives real-time information of systemati operation status. The
following table provides des riptions of LED status and their meaning.
LED Status Color Des ription
RJ45
On Green
A network devi e is
dete ted(10/100/1000 Mbps)
but no ommuni ation a tivity is
dete ted
Blinking Green
The Ethernet port is transmitting
to, or re eiving pa kage from
another devi e
Off -- No devi e is dete ted
Power
On Green Power feeding normally
On Red Power or fan alarm
Off -- Power off
Ports
On Green Power feeding
Blinking Orange Dete ting
On Orange The port has been shutdown
No power feeding
On Red Alarm
No power feeding
Off -- Unknown devi e atta hed
No power feeding
Table 2-1. The Description of LED Indicators
Rear Panel
The AC inlet, DC input terminal, and 4 Ventilation fan are lo ated at the rear panel. The
devi e will work with AC in the range 100-240V AC, 50-60Hz. Or work with DC
(-42~-57VDC for PSE-608R/616R/624R, 40V~60VDC for PSE-608RI/616RI)

User’s Manual PSE-608R(I)/616R(I)/624R
6
Power On
Conne t the power ord to the power so ket on the rear panel of the PSE. The other side
of power ord onne ts to the power outlet. The internal power supply of the PSE works
with voltage range of AC in the 100-240VAC, frequen y 50~60Hz, or with voltage range of
DC in the -42~-57VDC (40~60V for PSE-608RI/616RI). Che k the power indi ator on the
front panel to see if power is properly supplied.
Network Application
The PSE an provide power to the PD that follow the IEEE 802.3af/IEEE802.3at standard
in the network. It an solve the problem of position limitation. The network devi e an be
installed in more appropriate position for better performan e. The following figure is an
example of network appli ation for PSE

User’s Manual PSE-608R(I)/616R(I)/624R
7
RJ-4 Remote Control Port
PSE-608R(I)/616R(I)/624R an remotely manage the PoE via the network. To manage
PSE-608R(I)/616R(I)/624R, you must to set the PSE-608R(I)/616R(I)/624R TCP/IP
parameter.
PSE-608R(I)/616R(I)/624R allowed you to use a standard Web-browser su h as Mi rosoft
Internet Explorer or Mozila, to set the TCP/IP parameter.
Before you use the web interfa e to set the PoE TCP/IP, verify that
PSE-608R(I)/616R(I)/624R is properly installed on your network and PC on the network
an a ess PoE via the web-browser.
1. Verify that PC network interfa e ard (NIC) is operational on the TCP/IP proto ol.
2. Supply power to PSE608R/616R/624R.
3. Use RJ45 able, onne t PSE608R/616R/624R dire t to your PC.
4. Make sure the PSE608R/616R/624R default IP is 192.168.1.10.
5. Set your PC IP to 192.168.1.2 or other IP address whi h is lo ated in the 192.168.1.x
subnet.
6. Make sure the onne tor is OK (Ping 192.168.1.10 on the DOS mode).
7. Start the web-browser and type http://192.168.1.10 (or used PoE IP setting i on in the
PoE management software).
8. The login in s reen will appear next.

User’s Manual PSE-608R(I)/616R(I)/624R
8
9. Key in ID (user name) and password to enter PoE TCP/IP parameter setting.
Default ID and password is “admin” and “system”.
10. PSE-608R(I)/616R(I)/624R TCP/IP parameter has 4 pages interfa e (administrator
setting, TCP Mode, UDP Mode and UART). You must hange the administrator & TCP
mode to fit your network.

User’s Manual PSE-608R(I)/616R(I)/624R
9
11. Administrator setting: you an assign ni kname, IP setting, user name, password and
view system information.
Ni kname: You an assign a name to the devi e.
IP Address: You must assign the IP address reserved by your network. The default IP is
192.168.1.10.
Subnet Mask: You an assign the subnet mask for the IP address. The default subnet
mask is 255.255.255.0.
Gateway: You an assign the gateway here. The default gateway is 192.168.1.1.
IP Configure: You must assign to Stati for PoE serve operation. The default IP onfigure
is Stati .
Username: You an assign new user name. The default setting is admin.
Password/Confirm: You an type in new password here. The default setting is system.
When you have finished the set up, li k on Update to update your setting.

User’s Manual PSE-608R(I)/616R(I)/624R
10
12. TCP Mode: You an update the TCP ontrol parameter here.
Telnet Server/Client: Set to Server for PoE management operation.
Port Number: You an assign port number for TCP/IP operation. The default Port Number
is 23.
Remote Server IP Address: Unused.
Clint mode ina tive timeout: Unused.
Server mode prote t timeout: Set to 0(Disable) for normal operation.
When you have finished the set up, li k on Update to update your setting.
PS: The PSE-608R(I)/616R(I)/624R don’t used in the Telnet terminal.