MSI X340 User manual

X340 (MS-1352) Disassemble Guide
■ 1、BATTERY PACK
■ 2、LOWER CASE ASSY
■3、KEYBOARD
■4、SEPARATE UPPER CASE AND LOWER CASE
■5、HDD MODULE
■ 6、WLAN MODULE
■ 7、LOWER CASE ASSY-1
■ 8、RAM MODULE
■9、LOWER CASE ASSY-2
■10、UPPER CASE ASSY
■11、LCD MODULE ASSY

X340（MS-1352）Disassemble Guide
1、BATTERY PACK
1.1：Move the “Unlock’ button base on left picture
shows;
1.2：Release the “Release” button and move the
battery pack base on left picture.
Component P/N Qty
Battery Pack S9N-2141200-SB3 1

X340（MS-1352）Disassemble Guide
2、LOWER CASE ASSY
2.1：Push the Dummy card firstly, then remove it
after it pop up;
Component P/N Qty
Dummy Card E2P-3512611-Y31 1
2.2：Remove the 10 screws (M2*2.5mm);
Attention: the screw driver touque is: 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1202506-H29 10

X340（MS-1352）Disassemble Guide
3、KEYBOARD
3.1：Before removing K/B, firstly release the 2
hooks of the middle of the keyboard upside.
3.2：Insert the stick below the keyboard
3.3：Release the 2 hooks of the two sides of the
keyboard upside, then raise upside of the keyboard

X340（MS-1352）Disassemble Guide
3、KEYBOARD
3.4：Insert the plate, then move the plate from left
to right to remove double-sided adhesive pad.
3.5：Remove the keyboard.
3.6：Firstly push the handspike on two sides of the
K/B cable connector according to the direction as
pic shows; then remove the cable;
Component P/N Qty
Keyboard S1N-1ETC211-SA0 1

X340（MS-1352）Disassemble Guide
4、SEPARATE UPPER CASE AND LOWER CASE
4.1：Remove the 6 screws(M2*3.5mm);
Attention: the screw driver torque is: 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203501-H29 6
4.2：When remove the Upper case, firstly remove
the right side. Lift the inside of the upper with the
thumb; the other fingers push the upper to left.
4.3：Then remove the left side. Lift the inside of the
upper with the thumb; the other fingers push the
upper to right.

X340（MS-1352）Disassemble Guide
4、SEPARATE UPPER CASE AND LOWER CASE
4.4：When remove the Upper case, detach the
Upper case down side from Lower case;
Attention: Don’t use the heavy strength to
pull the Upper case; and the Touchpad cable
is connected with the main board;
4.5：First release the connector that stabilize the
cable, then remove Touchpad cable according to
the direction that pic shows;

X340（MS-1352）Disassemble Guide
5、HDD MODULE
5.1：Remove the 2 screws(M2*3.5mm);
Attention: the screw driver torque: 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203501-H29 2
5.2：Remove the HDD Module according to the
direction as pic shows;

X340（MS-1352）Disassemble Guide
5、HDD MODULE
5.3：Remove the 3 screws(M3*3.5mm)
that stabilize the bracket;
Attention: the screw driver torque is 3.0-3.5Kgf-cm
Component P/N Qty
Screw E43-1303502-H29 3
5.4：Remove the 3 HDD bracket;
Component P/N Qty
HDD Bracket 307-3510611-A89 3
HDD Module S71-2432504-F06 1

X340（MS-1352）Disassemble Guide
6、WLAN MODULE
6.1：Remove 2 screws(M2*3.5mm)
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203501-H29 2
6.2：Remove the Wlan board as left pic shows:
Component P/N Qty
Wlan Board 607-1352P-01S 1
6.3：Remove the two side wireless card antenna
as pic shows:

X340（MS-1352）Disassemble Guide
6、WLAN MODULE
6.4：Remove one screw(M2*3.5mm);
Attention: the screw driver torque is: 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203501-H29 1
6.5：Remove the WLAN module according to the
direction of pic shows;
Component P/N Qty
WLAN Module S57-0800183-I06 1

X340（MS-1352）Disassemble Guide
7、LOWER CASE ASSY-1
7.1：Remove the LVDS cable as pic shows:
7.2：Then remove the LINK cable
7.3：Remove the Speaker cable and MIC cable
separately as pic shows；
Speaker Cable
MIC Cable

X340（MS-1352）Disassemble Guide
7、LOWER CASE ASSY-1
7.4：Remove the 3 screws(M2*3.5mm)
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203501-H29 3
7.5：Remove the I/O board of right side as pic
shows:
Component P/N Qty
Right Side I/O Board 607-1352N-02S 1
7.6：Remove the LINK cable that connect with the
Right side I/O board, then remove the Audio cover
and DCIN cover on this board;
Component P/N Qty
LINK Cable K10-3024011-H39 1
Audio Cover E2P-3511411-D37 2
DCIN Cover E2P-3510911-D37 1

X340（MS-1352）Disassemble Guide
7、LOWER CASE ASSY-1
7.7：Remove the 4 screw (M2*3.5mm)that stabilize
the right hinge
Attention: the screw driver torque is 2.0-2.2Kgf-cm
Component P/N Qty
Screw E43-1203501-H29 4
7.8：Remove the 3 screw (M2*3.5mm)that stabilize
the left hinge
Attention: the screw driver torque is 2.0-2.2Kgf-cm
Component P/N Qty
Screw E43-1203501-H29 3

X340（MS-1352）Disassemble Guide
8、RAM MODULE
8.1：Push the two side shielding of RAM as pic
shows;
8.2：Then remove the RAM module according the
direction as pic shows;
Component P/N Qty
RAM Module S7C-S357102-T10 1

X340（MS-1352）Disassemble Guide
9、LOWER CASE ASSY-2
9.1：Remove the 3 screw (M2*3.5mm)
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203501-H29 3
9.2：Remove the left side I/O port as left pic
shows:
Component P/N Qty
Left Side I/O Board 607-1352O-01S 1

X340（MS-1352）Disassemble Guide
9、LOWER CASE ASSY-2
9.3：Remove the DSUB cover and MODE cover
on left side I/O board;
Component P/N Qty
DSUB Cover E2P-3510811-D37 1
MODE Cover E2P-3510711-D37 1
9.4：Remove the Bluetooth cable as left pic
shows:
Component P/N Qty
Bluetooth Cable K10-3008091-H39 1
9.5：Remove the 1 screw (M2*3.5mm)
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203501-H29 1

X340（MS-1352）Disassemble Guide
9、LOWER CASE ASSY-2
9.6：Remove the B/T module;
Component P/N Qty
Bluetooth Module 605-6837D-150 1

X340（MS-1352）Disassemble Guide
9、LOWER CASE ASSY-2
9.7：Firstly remove the Mylar pasted on heatsink,
then remove the 3 screws(M2*3.5mm), after that
remove the heatsink
Attention：the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203501-H29 3
Heatsink E31-0801210-TA9 1
9.8：Remove 2 screws (M2*3.5mm)
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203501-H29 2
9.9：Remove 2 screws (M2*3.5mm)
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203501-H29 2
2
1
2
1
2
3
1

X340（MS-1352）Disassemble Guide
9、LOWER CASE ASSY-2
9.10：Remove the main board from Lower case
and Pull out the fan cable as pic shows;
9.11：Remove the fan from main board
Attention: the fan cable should be pulled out from
the breach of main board.
Component P/N Qty
Main Board 607-13521-02S 1
Fan E33-0800080-MC2 1