MSV N1250 User manual

0

1
MSV - N1250 IP Camera
Hardware User Manual
-Contents-
Statement and Declaration
CHAPTER 1. SAFETY INSTRUCTION ........................................................................................6
CHAPTER 2. INTRODUCTION .....................................................................................................8
CHAPTER 3. PACKAGE CONTENTS ..........................................................................................9
CHAPTER 4. PHYSICAL DESCRIPTION..................................................................................10
4.1 F RONT V IEW .......................................................................................................................................................... 10
4.2 B OTTOM V IEW ....................................................................................................................................................... 11
CHAPTER 5. BASIC CONNECTION ..........................................................................................12
5.1 W IRE C ONNECTION ............................................................................................................................................... 12
5.2 W IRELESS CONNECTION ........................................................................................................................................ 12
CHAPTER 6. APPLICATION........................................................................................................13

2
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The
followin test methods have been applied in order to prove presumption of conformity with the
essential requirements of the R&TTE Directive 1999/5/EC:
Cl use Description
EN 60950-1: 2001 Safety of Information Technolo y Equipment
EN 50392: 2004
Generic standard to demonstrate the compliance of electronic and
electrical apparatus with the basic restrictions related to human
exposure to electroma netic fields (0 Hz - 300 GHz)
EN 300 328 V1.6.1
(2004-11)
Electroma netic compatibility and Radio spectrum Matters (ERM);
Wideband transmission systems; Data transmission equipment
operatin in the 2,4 GHz ISM band and usin wide band modulation
techniques; Harmonized EN coverin essential requirements under
article 3.2 of the R&TTE Directive
EN 301 489-17 V1.2.1
(2002-08) nd EN 301
489-1 V1.5.1 (2004-11)
Electroma netic compatibility and Radio spectrum Matters (ERM);
ElectroMa netic Compatibility (EMC) standard for radio equipment
and services; Part 17: Specific conditions for 2,4 GHz wideband
transmission systems and 5 GHz hi h performance RLAN equipment
This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU
member states and EFTA countries, except in France and Italy where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain
authorization to use the device for settin up outdoor radio links and/or for supplyin public access
to telecommunications and/or network services.
This device may not be used for settin up outdoor radio links in France and in some areas the RF
output power may be limited to 10 mW EIRP in the frequency ran e of 2454 – 2483.5 MHz. For
detailed information the end-user should contact the national spectrum authority in France.

3
Česky
[Czech]
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními
požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk
[Danish]
Underte nede [fabrikantens navn] erklærer herved, at føl ende udstyr [udstyrets
typebetegnelse] overholder de væsentli e krav o øvri e relevante krav i direktiv
1999/5/EF.
Deutsch
[German]
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [ erätetyp] in
Übereinstimmun mit den rundle enden Anforderun en und den übri en
einschlä i en Bestimmun en der Richtlinie 1999/5/EG befindet.
Eesti
[Estonian]
Käesoleva a kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp =
type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele sätetele.
En lish Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance
with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de equipo]
cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o
exi ibles de la Directiva 1999/5/CE.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ∆ΗΛΩΝΕΙ ΟΤΙ [type of equipment]
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ
ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ.
Français
[French]
Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme
aux exi ences essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE.
Italiano
[Italian]
Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla
direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of
equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem
ar to saistītajiem noteikumiem.
Lietuvių
[Lithuanian]
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Nederlands
[Dutch]
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in
overeenstemmin is met de essentiële eisen en de andere relevante bepalin en van
richtlijn 1999/5/EG.

4
Malti
[Maltese]
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma
mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva
1999/5/EC.
Ma yar
[Hun arian]
Alulírott, [gyártó neve] nyilatkozom, ho y a [... típus] me felel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv e yéb elõírásainak.
Polski
[Polish]
Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest z odny z
zasadniczymi wymo ami oraz pozostałymi stosownymi postanowieniami Dyrektywy
1999/5/EC.
Portu uês
[Portu uese]
[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os
requisitos essenciais e outras disposições da Directiva 1999/5/CE.
Slovensko
[Slovenian]
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in
ostalimi relevantnimi določili direktive 1999/5/ES.
Slovensky
[Slovak]
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a
všetky príslušné ustanovenia Smernice 1999/5/ES.
Suomi
[Finnish]
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen
tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
Härmed inty ar [företag] att denna [utrustningstyp] står I överensstämmelse med de
väsentli a e enskapskrav och övri a relevanta bestämmelser som fram år av direktiv
1999/5/EG.

5
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B di ital device,
pursuant to Part 15 of the FCC Rules. These limits are desi ned to provide reasonable protection
a ainst harmful interference in a residential installation. This equipment enerates, uses and can
radiate radio frequency ener y and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no uarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turnin the equipment off
and on, the user is encoura ed to try to correct the interference by one of the followin measures:
• Reorient or relocate the receivin antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the followin two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, includin interference that may cause
undesired operation.
FCC C ution:
Any chan es or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firm are-limited to channels 1 through 11.
IMPORTANT NOTE:
FCC R di tion Exposure St tement:
This equipment complies ith FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated ith minimum distance 20cm bet een the radiator & your body.
This transmitter must not be co-located or operating in conjunction ith any other antenna or transmitter.

6
Hardware User Manual
Chapter 1. Safety Instru tion
Before you use this product
This product has been desi ned with safety in mind. However, the electrical products can cause
fires which may lead to serious body injury if not used properly. To avoid such accidents, be sure to
heed the followin .
Legal Caution
Video and audio surveillance can be forbidden by laws that vary from country to country. Check the
laws in your local re ion before usin this product for surveillance purposes.
Don't open the housing of the product
Don't try to open the housin or remove the covers which may expose yourself to dan erous volta e
or other hazards.
Don't use the accessories not recommend by the manufacturer
Heed the safety precautions
Be sure to follow the eneral safety precautions and the “Operation Notice.”
Operation Notice - Operating or storage location
Avoid operatin or storin the camera in the followin locations:
• Extremely hot or cold places
(Operatin temperature: 0 °C to + 50 °C [32 °F to 122°F] )
• Exposed to direct sunli ht for a lon time, or close to heatin equipment (e. ., near heaters)
• Close to water (e. .,near a bathtub, kitchen sink, laundry tub)
• Close to sources of stron ma netism
• Close to sources of powerful electroma netic radiation, such as radios or TV transmitters
• Locations subject to stron vibration or shock

7
In case of a breakdo n
In case of system breakdown, discontinue use and contact your authorized dealer.
In case of abnormal operation
• If the unit emits smoke or an unusual smell,
• If water or other forei n objects enter the cabinet, or
• If you drop the unit or dama e the cabinet:1 Disconnect the cable and the connectin cables. 2
Contact your authorized dealer or the store where you purchased the product.
Transportation
When transportin the camera, repack it as ori inally packed at the factory or in materials of equal
quality.
Ventilation
To prevent heat buildup, do not block air circulation around the device.
Cleaning
• Use a soft, dry cloth to clean the external surfaces of the device. Stubborn stains can be
removed usin a soft cloth dampened with a small quantity of deter ent solution, then wipe dry.
• Do not use volatile solvents such as alcohol, benzene or thinners as they may dama e the
surface.

8
Chapter 2. Introdu tion
The N1250 is an ultra-compact IP Camera equipped with a hi h sensitivity pro ressive scan CMOS
sensor, achievin hi h ima e quality and superior low-li ht performance. N1250 also supports
802.11b/ wireless connection and ni ht-vision capability even in complete darkness throu h 6 hi h
power LEDs.
Key Features:
• Maximum Resolution 640x480 (VGA) provides superior ima e quality
• Simultaneous MPEG-4 and Motion JPEG video stream
• Excellent Ima e Quality up to flexible 30 fps in all resolution for optimum bandwidth use
• Superior Low-Li ht Performance with 6 Ni ht-Vision LEDs down to 0 Lux
• Wireless( IEEE 802.11 /b) Networks Connection
• Two-way Audio with Built-In Microphone
• Optimal Synchronization of Audio and Video
• Support Live Video Viewing on Windows Live Messenger (WLM )
• Control p nel dd-in, i.e. sn pshot nd im ge setup
• Support M c OS with S f ri Browser
• Support iPhone through S f ri Browser
• Mobile Phone Streamin Live Video throu h 3GPP / ISMA / RTSP
• Mobile Phone Live Ima e throu h 2.5 WAP
• Multi-level Password Protection for Restrictin Camera Access
• Built-In Multi-Window Motion Detection (3 detection areas)
• Video Buffer makes the Streamin Smoother
• UPnP nd Bonjour for Fast and Easy Installation
• DDNS Supported
• Bundled 16 Channel Surveillance Software
• User-friendly & Multi-lin ual UI

9
Chapter 3. Pa kage Contents
Camera – N1250 IP Camera
Quick Installation Guide - To provide brief product information and quick installation and
wireless settin
Soft are CD - To provide IP Surveillance Software, Intelli ence IP Installer, User Manuals, and
Lan ua e Packs
Mounting Bracket – There are three components includin lock rin , brace, and base plate to
compose a bracket and three applied screws to fix the base plate to a flat surface (horizontal or
vertical)
Antenna - For connection of IEEE 802.11 b / wireless network
Adaptor - 5V DC, max 5W

10
Chapter 4. Physi al Des ription
4.1 Front View
Focus Adjustment Ring - Adjust focus manually to achieve the best ima e quality
Night-Vision White LEDs - LEDs will li ht up when the environment is too dark.
Power LED indic tor - Power LED will li ht up after the IP Camera completed the boot
process
Network LED indic tor - Network LED will li ht up after the IP Camera connected with
network.
Built-In Microphone - Built-In Microphone for Two-way Audio
Wireless Antenn - For connection of IEEE 802.11 b / wireless network.

11
4.2 Bottom View
Power Connector - For connection of 5V DC input.
Reset – When the device is empowered, press the Reset Button to reboot the device, or
hold the Reset Button for 10 seconds to set the device settin s back to factory default
Audio Out (Spe ker) - To support audio out with earphones or speakers
Network Connector - For connection to the Ethernet via RJ-45 standard

12
Chapter 5. Basi Conne tion
N1250 is for both wire and wireless connection. You can follow the procedure below to connect the
IP Camera with power and Ethernet for both wire and wireless connection.
5.1 Wire Connection
1. Connect the power adaptor to IP Camera.
2. Connect IP Camera’ Ethernet port to your Hub/ Switch / Router
5.2 Wireless connection
1. Connect the power adaptor to IP Camera.
3. Connect to Wi-Fi
Wire Connection
Wireless Connection

13
Chapter 6. Appli ation