MTD 19A70020OEM Service manual

ATTACHMENT / ZERO TURN SERIES
Service Advisory MTD-144
1 of 2
PURPOSE:
If installing a 19A70020OEM 42/46” RZT Bagger or 19A70004OEM 50” RZT Bagger onto a Model Year 2013 RZT-L, a
left hand and right hand counter weight bracket and mounting hardware will be required to install the counter weight.
ACTION REQUIRED: This advisory is for INFORMATIONAL PURPOSES ONLY
January 16, 2013
Counter Weight Mounting Brackets.
19A70020OEM 42/46” RZT Bagger.
19A70004OEM 50” RZT Bagger.
Models Affected:
Subject:
Date:
All Above Production Baggers, When Used On MY 2013 RZT-L.
Serial Number
Range Affected:
DISCUSSION:
1. Verify that the Bagger is one of the above listed Baggers Models Affected.
2. Confirm that the unit is a Model Year 2013 RZT- L.
3. Order the following from your parts source:
Item 1. Qty. (1) 703-09197-0637 LH Weight Mounting Bracket
Item 2. Qty. (1) 703-09193-0637 RH Weight Mounting Bracket
Item 3. Qty. (1) 689-00325 RZT Counter Weight Hardware Pack
4. See instructions for counter weight bracket installation on back of this Advisory.
NOTE: The 19B70020OEM and 19B70004OEM Baggers Will Have The LH and RH Weight Mounting Brackets
and RZT Counter Weight Hardware Pack Included.
NOTE: These materials are prepared for use by trained technicians who are experienced in the service and repair of
equipment of the kind described in this publication, and are not intended for use by untrained or inexperienced
individuals. Such individuals should seek the assistance of an authorized service technician or dealer.
NOTE: Always wear eye protection while servicing equipment. Wear hearing protection when appropriate. Always work
in a well ventilated area and follow all safety precautions when dealing with combustible materials.
NOTE: Left (LH) and Right (RH) sides are determined from the operator’s position and facing in the forward direction.
SERVICE MANAGER PARTS MANAGER SALES MANAGER SERVICE TECH. SERVICE TECH.
Circulate and Initial

Advisory MTD-144 2 of 2
1
2
3
3
3
3
3
3
3
3
Counter Weight
From 42/46” or 50”
Stationary Solid Front Axle
Shown For Reference Only
FIGURE 1
two (2) 3/8-16 Nylon Lock Flange Nuts from item # 3
(689-00325) Hardware Pack as shown in Figure 1. Do
Not tighten hardware at this time.
5. Install the weight brackets with counter weight to the
stationary solid front axle using the two (2) 5/16-18 x
3.25” Hex Head Cap Screws and two (2) 5/16-18 Nylon
Lock Flange Nuts from item # 3 (689-00325) Hardware
Pack.
6. Tighten all hardware securely from steps 4 and 5.
7. Finish following the instructions provided with the
42/46” or 50” RZT Bagger assembly.
Installation Instructions:
1. Follow the instructions provided with the 42/46” or 50”
RZT Bagger assembly.
2. Disregard the section of instructions for installing the
counter weight provided with the 42/46” or 50” RZT Bag-
ger assembly.
3. Follow steps 4 through 6 for installing the counter
weight provided in the 42/46” or 50” RZT Bagger assem-
bly while using the newly ordered LH and RH Weight
Mounting Brackets and Hardware Pack.
4. Install item #1 (703-09197-0637) Left Hand Weight
Mounting Bracket and item # 2 (703-09193-0637) Right
Hand Weight Mounting Bracket to the counter weight
from the 42/46” or 50” RZT Bagger assembly using the
two (2) 3/8-16 x 2.50” Hex Head Cap Screws and
5/16-18 x 3.25”
Hex Head
Cap Screw
5/16-18 x 3.25”
Hex Head
Cap Screw
5/16-18
Nylon Lock
Flange Nut
5/16-18
Nylon Lock
Flange Nut
3/8-16
Nylon Lock
Flange
3/8-16
Nylon Lock
Flange
3/8-16 x 2.50”
Hex Head
Cap Screw
3/8-16 x 2.50”
Hex Head
Cap Screw
Bagger Assembly