Muller Elektronik Joystick III User manual

Installation and operating instructions
Joystick III
Version: V3.20180409
3032258305-02-EN
Read and follow these operating instructions.
Keep these operating instructions in a safe place for
later reference.

Company details
Installation and operating instructions
Product: Joystick III
Document number: 3032258305-02-EN
As of software version: 7.03
Original language: German
Müller-Elektronik GmbH & Co.KG
Franz-Kleine-Straße 18
33154 Salzkotten
Germany
Phone: ++49 (0) 5258 / 9834 - 0
Fax: ++49 (0) 5258 / 9834 - 90
Email: [email protected]
Homepage: http://www.mueller-elektronik.de
Document
Copyright ©

Table of contents
V3.20180409
3
Table of contents
1
Product description
4
2
Assembly instructions
5
2.1
Fitting a joystick with a Sub-D connector
5
2.2
Fitting a joystick with a CPC connector
6
2.3
Fitting a joystick with a CPC connector and a CPC socket
6
3
Configuring the joystick
8
4
Operation
10
4.1
Executing functions
10
4.2
Changing the brightness of the LED
10
4.3
Assigning functions
10
4.4
Viewing functions
10
5
Technical specifications
12
5.1
Technical specifications of the joystick
12
5.2
Sub-D connector pin assignment
12
5.3
CPC connector pin assignment
12
5.4
Disposal
12
5.5
Information on the rating plate
13
6
EU declaration of conformity
14

1
Product description
4
3032258305-02-EN
Product description
Joystick III
Eight buttons
Numbering of the buttons
LED
Side-mounted switch
Rating plate [➙13]
The joystick is an ancillary operating device which can rapidly access the functions
of an ISOBUS job computer.
The joystick is fitted with eight buttons and a single side-mounted switch, which
enables switching between three levels. This enables the actuation of a total of 24
functions on the ISOBUS job computer. The current level is indicated by an LED.
The joystick can be used to operate ISOBUS job computers which support the
Auxiliary 1 or Auxiliary 2 protocols. Find out more about the protocol which you
should choose here: [➙8]
1

Assembly instructions
Fitting a joystick with a Sub-D connector
2
V3.20180409
5
Assembly instructions
The joystick is available in three versions:
▪With Sub-D connector (item no.: 3032258305)
–Variant for vehicles with additionally installed ISOBUS basic vehicle harness
from Müller-Elektronik.
▪With CPC connector (item no.: 3032258606)
–Variant for vehicles with integrated ISOBUS in-cab-connector.
▪With CPC connector and CPC socket (item no.: 3032258106)
–Variant for vehicles with integrated ISOBUS in-cab-connector and a CPC-
Sub-D adapter cable between terminal and joystick.
Fitting a joystick with a Sub-D connector
Angle brackets
For attachment in the cabin
Connector for connection to the
terminal
Socket for connection to the basic
vehicle harness
You fit the joystick as follows:
1. Fit the joystick next to the driver on the right.
2. Plug the connector of the basic vehicle harness into the joystick socket.
3. Connect connector A of the joystick to the CAN bus socket of the terminal. For
the majority of terminals from Müller-Elektronik this is going to be the A socket.
⇨The joystick now connects the basic vehicle harness with the terminal.
⇨When the terminal is switched on, the LED on the joystick lights up.
2
2.1
Procedure

2
Assembly instructions
Fitting a joystick with a CPC connector
6
3032258305-02-EN
Fitting a joystick with a CPC connector
Angle brackets
For attachment in the cabin
Connector for connection to the
vehicle's ISOBUS In-Cab-
Connector
You fit the joystick as follows:
1. Fit the joystick next to the driver on the right.
2. Plug the connector into the ISOBUS in-cab-connector of your vehicle.
⇨The joystick is now connected to your vehicle.
⇨When the vehicle is switched on, the LED on the joystick lights up.
Fitting a joystick with a CPC connector and a CPC socket
Angle brackets
For attachment in the cabin
Socket for connection to the CPC-
Sub-D adapter cable.
Connector for connection to the
vehicle's ISOBUS In-Cab-
Connector
You fit the joystick as follows:
1. Fit the joystick next to the driver on the right.
2.2
Procedure
2.3
Procedure

Assembly instructions
Fitting a joystick with a CPC connector and a CPC socket
2
V3.20180409
7
2. Plug the connector into the ISOBUS in-cab-connector of your vehicle.
3. Connect the CPC socket to a CPC connector to connect the joystick to a
terminal using an adapter cable.
⇨The joystick now connects the vehicle with the terminal.
⇨When the terminal is switched on, the LED on the joystick lights up.

3
Configuring the joystick
8
3032258305-02-EN
Configuring the joystick
Brightness for day or night mode:
Day mode
Selected auxiliary protocol
Selected joystick number
Cursor
Function
icon
Meaning
Switches between day and night mode
Increase brightness
Reduce brightness
When configuring the joystick, you can make the following settings:
▪Change the LED brightness in day and night mode.
▪If you use several joysticks, select the joystick number.
–The default value is “1”. When using multiple joysticks, you must number
these sequentially.
▪Select the Auxiliary protocol.
–“AUX1”
Select this protocol when your ISOBUS job computer and your terminal
support Auxiliary 1. You can then assign functions to the joystick.
OR
Select this protocol if you use an ME sprayer or a SECTION-Control BOX.
–“AUX2”
Select this protocol when your ISOBUS job computer and your terminal
support Auxiliary 2. You can then assign functions to the joystick.
3

Configuring the joystick
3
V3.20180409
9
If you don't know which protocol your system supports, you can test this by
selecting protocol “AUX2”. If you can then assign functions [➙10] for the
ISOBUS job computer to the joystick, your system supports Auxiliary 2.
Otherwise, select protocol “AUX1”.
To configure the joystick:
The terminal is switched off.
1. Hold button 2 on your joystick pressed down. You can recognize button 2 from
its white surround.
2. Start the terminal.
3. Release button 2 after approx. 5 seconds.
4. - Open the Joystick application.
5. Configure the joystick.
6. Restart the terminal.
Procedure

4
Operation
Executing functions
10
3032258305-02-EN
Operation
Executing functions
Each button on the joystick can be assigned three functions. The position of the
side-mounted switch determines the function which is performed when the button is
pressed:
Position of the switch
Color of the LED
Red
Yellow
Green
To operate the joystick:
1. Move the side-mounted switch to the desired position and hold it securely.
⇨The LED is lit in the appropriate color.
2. Press the button with the desired function.
⇨The function will be activated.
3. Release the side-mounted switch and the button to exit the function.
Changing the brightness of the LED
You can adjust the LED brightness to the daytime while working. You can choose
from a day mode and night mode.
To change the brightness of the LED:
1. Switch rapidly the side-mounted switch from its up position to the down position,
or vice-versa.
⇨The LED mode will change.
Assigning functions
You assign ISOBUS job computer functions using the terminal. You can read how to
do this in the operating instructions for the terminal.
Viewing functions
To view the functions which are assigned to the joystick:
4
4.1
Procedure
4.2
Procedure
4.3
4.4
Procedure

Operation
Viewing functions
4
V3.20180409
11
You have selected the appropriate protocol when configuring the joystick. [➙8]
Your ISOBUS job computer is connected to the vehicle's ISOBUS in-cab-
connector.
You have assigned functions to the joystick. [➙10]
1. Start the terminal.
2. Open the selection menu.
3. - Open the Joystick application.
⇨The following screen appears:
⇨You can then see which joystick button has been assigned to an ISOBUS job
computer function. The current level is shown on the right of the screen.

5
Technical specifications
Technical specifications of the joystick
12
3032258305-02-EN
Technical specifications
Technical specifications of the joystick
Parameters
Value
Operating voltage
10.5 V to 16 V DC
Temperature range
-20°C to +70°C
Current consumption
40 mA
Protection rating
IP20
Sub-D connector pin assignment
Pin no.
Signal
Pin no.
Signal
1
CAN_L_out
6
GND_E
2
CAN_L_in
7
CAN_H_in
3
CAN_GND
8
CAN_EN_out
4
CAN_H_out
9
+12 VE
5
CAN_EN_in
CPC connector pin assignment
Pin no.
Signal
Pin no.
Signal
Pin no.
Signal
1
12 VE
4
CAN_H
7
12 VE
2
CAN_L
5
CAN_H
8
3
CAN_L
6
9
0 VE
Disposal
When it has reached the end of its service life, please dispose of this
product as electronic scrap in accordance with all applicable waste
management laws.
5
5.1
5.2
5.3
5.4

Technical specifications
Information on the rating plate
5
V3.20180409
13
Information on the rating plate
The nameplate is located on the underside of the joystick.
Abbreviations on the rating plate
Abbreviation
Meaning
Customer number
If the product was manufactured for an agricultural
machinery manufacturer, the agricultural machinery
manufacturer's item number will be shown here.
Hardware version
Müller-Elektronik item number
Operating voltage
The product may only be connected to voltages within this
range.
Software version
Serial number
5.5

6
EU declaration of conformity
14
3032258305-02-EN
EU declaration of conformity
Herewith we declare that the product designated below, on the basis of its design
and construction in the form brought onto the market by us, is in accordance with the
relevant safety and health requirements of the EC Directive of Electromagnetic
Compatibility 2014/30/EU. If alterations are made to the product without prior
consultations with us, this declaration becomes invalid.
Product name:
ME_AR Joystick III 8+1 Taster ISO Sub-D
Aux1/Aux2, abgedichteter Taster
Item number:
3032258305
Variants:
3004700709
3032258106
3032258607
3055795908
3055795909
Harmonised standards applied:
EN ISO 14982:2009
(EMC Directive 2014/30/EU)
6