Muller Elektronik Joystick III User manual

Installation and operating instructions
Joystick III
Version: V2.20141208
3032258305-02-EN Read and follow these operating instructions.
Keep these operating instructionsin a safe place for
later reference.

Company details
Installation and operating instructions
Product: Joystick III
Document number: 3032258305-02-EN
From software version: 7.03
Original language: German
Müller-Elektronik GmbH & Co.KG
Franz-Kleine-Straße 18
33154 Salzkotten
Germany
Phone: ++49 (0)5258 / 9834 - 0
Fax: ++49 (0)5258 / 9834 - 90
Email: [e-mail]
Homepage: http://www.mueller-elektronik.de
Document
Copyright ©

Table of contents
V2.20141208
3
Table of contents
1
Product description
4
2
Assembly instructions
5
2.1
Fitting a joystick with a D-Sub connector
5
2.2
Fitting a joystick with a CPC connector
6
3
Configuring the joystick
7
4
Operation
9
4.1
Executing functions
9
4.2
Changing the brightness of the LED
9
4.3
Assigning functions
9
4.4
Viewing functions
9
5
Technical specifications
11
5.1
Technical specifications of the joystick
11
5.2
D-Sub connector pin allocation
11
5.3
CPC connector pin allocation
11
5.4
Disposal
12
5.5
Information on the nameplate
12
6
Notes
13

1 Product description
4
3032258305-02-EN
Product description
Joystick III
Eight buttons
Numbering of the buttons
LED
Side-mounted switch
Manufacturer's plate [➙12]
The joystick isan ancillary operating device which can rapidly access the functions
of an ISOBUS job computer.
The joystick is fitted with eight buttons and a single side-mounted switch, which
enables switching between three levels. This enables the actuation of a totalof 24
functions on the ISOBUS job computer. The currentlevelis indicated by an LED.
The joystick canbe usedto operate ISOBUS job computers which support the
Auxiliary 1 or Auxiliary2 protocols. Find out more aboutthe protocol which you
should choose here: [➙7]
1

Assembly instructions
Fitting a joystick with a D-Sub connector 2
V2.20141208
5
Assembly instructions
The joystick isavailable in two versions:
▪With D-Sub connector (item no.: 3032258305)
– Variantfor vehicles with additionally installed ISOBUS basic equipment from
Müller-Elektronik.
▪With CPC connector (item no.: 3032258606)
– Variant for vehicles with integrated ISOBUS in-cab-connector.
Fitting a joystick with a D-Sub connector
Mounting angle
For attachment in the cabin
Connector for connection to the
terminal
Socket for connection to the basic
vehicle harness
You fit the joystick asfollows:
1. Fit the joysticknext tothe driver on the right.
2. Plug the connector of the basic vehicle harness into the joystick socket.
3. Connect connectorA of the joystick to the CANbus socket of the terminal. For
the majority of terminals from Müller-Elektronik thisis going to be the A socket.
⇨The joystick now connects the basicvehicleharness with the terminal.
⇨When the terminal is switched on,the LED on the joystick lights up.
2
2.1
Procedure

2 Assembly instructions
Fitting a joystick with a CPC connector
6
3032258305-02-EN
Fitting a joystick with a CPC connector
Mounting angle
For attachment in the cabin
Connector for connection to the
vehicle's ISOBUS in-cab-
connector
You fit the joystick asfollows:
1. Fit the joysticknext tothe driver on the right.
2. Plug the connectorinto the ISOBUS in-cab-connector of your vehicle.
⇨The joystick is nowconnected to your vehicle.
⇨When the vehicle is switched on, the LEDon the joystick lights up.
2.2
Procedure

Configuring the joystick
3
V2.20141208
7
Configuring the joystick
Brightness for day or night mode:
Day mode
Selected auxiliary protocol
Selected joystick number
Cursor
Function
icon
Meaning
Switches between day and night mode
Increase brightness
Reduce brightness
When configuring the joystick, you can make the following settings:
▪Change the LED brightness in day and night mode.
▪If you use several joysticks, select the joystick number.
– The default value is "1". When using multiple joysticks, you must number
these sequentially.
▪Select the Auxiliary protocol.
– "AUX1"
Select this protocol when your ISOBUS job computer and your terminal
support Auxiliary 1. You can then assign functions to the joystick.
OR
Select this protocol if you use an ME sprayer or a SECTION-Control BOX.
– "AUX2"
Select this protocol when your ISOBUS job computer and your terminal
support Auxiliary 2. You can then assign functions to the joystick.
3

3 Configuring the joystick
8
3032258305-02-EN
If you don't knowwhich protocolyour system supports,you can test thisby
selecting protocol "AUX2". If you can then assign functions[➙9] for the
ISOBUS job computer to the joystick, yoursystem supports Auxiliary 2.
Otherwise, select protocol "AUX1".
To configure the joystick:
The terminal is switched off.
1. Hold button 2 on your joystick pressed down. You can recognize button 2 from
its white surround.
2. Start the terminal.
3. Release button 2 after approx. 5 seconds.
4. - Open the Joystick application.
5. Configure the joystick.
6. Restart the terminal.
Procedure

Operation
Executing functions 4
V2.20141208
9
Operation
Executing functions
Each button on thejoystick can be assigned three functions. The position ofthe
side-mounted switch determinesthe function which is performed when the button is
pressed:
Position of the switch
Color of the LED
Red
Yellow
Green
To operate the joystick:
1. Move the side-mounted switch to thedesired position and hold it securely.
⇨The LED is lit in the appropriate color.
2. Press the button with thedesired function.
⇨The function willbe activated.
3. Release the side-mounted switch and the button to exit the function.
Changing the brightness of the LED
You canadjustthe LEDbrightness tothe daytime while working. You can choose
from a day mode and nightmode.
To change the brightness of the LED:
1. Switch rapidly the side-mounted switch fromitsup position to the down position,
or vice-versa.
⇨The LED modewill change.
Assigning functions
You assign ISOBUS job computer functions using the terminal. You can read howto
do thisin the operating instructions forthe terminal.
Viewing functions
To viewthe functions which are assigned to the joystick:
4
4.1
Procedure
4.2
Procedure
4.3
4.4
Procedure

4 Operation
Viewing functions
10
3032258305-02-EN
Youhave selected the appropriateprotocolwhen configuring the joystick. [➙7]
YourISOBUS job computer isconnected to the vehicle's ISOBUS in-cab-
connector.
You have assigned functions to the joystick. [➙9]
1. Start the terminal.
2. Open the selection menu.
3. - Open the Joystick application.
⇨The following screen appears:
⇨You can then see which joystick button hasbeen assignedto an ISOBUS job
computerfunction. The current level is shown on the right of the screen.