mundoclima ALL IN ONE Type Air-source Heat Pump Water... Operating instructions

Thank you very much for purchasing our product,
Before using your unit , please read this manual carefully and keep it for future reference.
INSTALLATION & OWNER’S MANUAL
ALL IN ONE Type Air-source Heat Pump Water Heater

WARNING
This unit is required reliable earthing
before usage,otherwise might cause
death or injury
Please ask skilled service persons for
reliable earthing connection
Your safety is the most important thing we concerned !

PARTS NAMES
NOTE
All the picture in this manual are for explanation purpose only. They may be slightly different from the heat pump water heaterr you
purchased (depand on model).The actual shaped shall prevail.
Front Cover
Electronic Control Box
Compressor
Display
Cover
Front Decorative Board
Cover(Electric Heater)
TCO
Electric Heater
TOD
PT Valve
Water Outlet
Rear Cover
Junction Box
Junction Box Cover
Top Cover
Air Inlet
Fan Assy
Evaporator
Filter
Air Outlet
Water Inlet
Anode Rod
Drain Pipe
Solar Sensor
Solar Water Inlet
Solar Water Outlet

1
Installation & Owner‘s Manual
CONTENTS PAGE
1. PRECAUTIONS
To prevent injury to the user or other people and property damage，
the following instructions must be followed. Incorrect operation due
to ignoring of instructions may cause harm or damage.
WARNING
WARNING
CAUTION
Failure to observe a caution may result in injury or damage
to the equipment.
Failure to observe a warning may result in death or serious
Injury.
The water heating unit must be earthed effectively .
A creepage breaker
must
be installed near the power
supply
Do not tear off the labels on the units for the purpose of
warning or reminding
The safety precautions listed here are divided into two categories.
In either case, important safety instructions are listed to which
close
attention must be paid.
WARNING
Ask the professional installer for installation of the air source
heat pump water heating units，improper installation may
result in water leakage, electric shock, or fire.
Ask the professional service person for the repair and
maintenance.
Improper repair and maintenance may result in water leakage,
electric shock or fire.
In order to avoid electric shock,fire or injury,if any abnormality
is detected,such as smell of fire,turn off the power supply and
call your service agent for instructions.
Never use the wire and fuse with wrong rated current..
Use of wrong wire or fuse may cause the unit to break down
or a fire.
Do not insert fingers, rods or other objects into the air inlet or
outlet.
When the fan is rotating at high speed, it will cause injury.
Never use a flammable spray such as hair spray, lacquer
paint near the unit.
It may cause a fire.
Never touch the air outlet or the horizontal blades while the
swing flap is in operation.
Fingers may become caught or the unit may break down.
Never put any objects into the air inlet or outlet.
Objects touching the fan of high speed can be dangerous.
Do not dispose this product as unsorted municipal
waste.Collection of such waste separately for special
treatment is necessary.
The appliance shall be installed in accordance national wiring
regulations.
The appliance should not be used by children without
supervision.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
An all-pole disconnection device which has at least 3mm
separation distance in all pole and a residual current
device(RCD)with the rating of above 10mA shall be incorpo-
rated in the fixed wiring according to the national rule.
DISPOSAL: Do not dispose this product as unsorted
municipal waste. Collection of such waste separately for
special treatment is necessary.
Do not dispose of electrical appliances as unsorted municipal
waste, use separate collection facilities.
Contact you local government for information regarding the
collection systems available.
If electrical appliances are disposed of in landfills or dumps,
hazardous substances can leak into the groundwater and get
into the food chain, damaging your health and well-being.
1
2
2
3
4
5
6
8
1
4
1
PRECAUTIONS......................................................................................
ACCESSORIES......................................................................................
INSTALLATION LOCATION.....................................................................
INSTALLATION .....................................................................................
PIPELINE CONNECTION .......................................................................
DUCT CONNECTION WAY.......................................................................
ELECTRIC CONNECTION.......................................................................
OPERATING INSTRUCTION...................................................................
RUNNING AND CAPABILITY...................................................................
MAINTENANCE......................................................................................
SPECIFICATIONS...................................................................................

2
Installation & Owner‘s Manual
CAUTION
The earth pole of terminal must be earthed,and the rated
current should be more than 10A. Make sure that power
supply terminal and power supply plug are dry enough and
have a good connection.
Method: Turn on power supply run the unit for half a hour then
turn it off and check whether the power supply plug is hot or
nor.If it’s hot (more than 50℃),please change it with a new
and eligible one, or it may result in an electric shock or fire.
Do not use the air-source water heater for other purposes.
Before cleaning,be sure to stop the operation and turn the
breaker off or pull out the power cord.
Otherwise, an electric shock and injury may be caused.
The hot water probable need to mix with cold water too hot
water (over 50℃) in the heating unit may could injury.
In order to avoid injury, do not remove the fan guard on the
outdoor unit.
Do not operate the air-source water heater with a wet hand.
An electric shock may be caused.
The installation height of power supply should be over 1.8m, if
any water may spatter. And safe from water.
In the water inlet side, the One Way valve must be installed.
It’s normal if some water drops from the hole of PT valve
during operation.Bit, if the water is in a great amount, call your
service agent for instructions.
After a long term use, check the unit stand and fittings.
If damaged, the unit may fall and result in injury.
Arrange the drain hose to ensure smooth drainpipe.
Improper drainpipe may cause wetting of the building, furniture
etc.
Do not touch the inner parts of the controller.
Do not remove the front panel. Some parts inside are
dangerous to touch, and a machine malfunction may be
caused.
Do not turn off the power supply.
System will stop or restart heating automatically. A continuous
power supply for water heating is necessary, except service
and maintenance.
Prevent water from
flowing back
2. ACCESSORIES
Table. 2-1
1
1
Accessory Name Qty. Sharp Purpose
Y-shaped Filter
Owner’s & Installation
Manual
Installation and use instruction
This manual
To filtrate inlet water
1
One Way Valve
3. INSTALLATION LOCATION
Enough space is installation and maintenance shall be
preserved.
The air inlet and outlet should be free from obstacles and strong
wind.
The bearing surface should be flat able to bear weight of the
unit and suitable for installing the unit without increasing noise
or vibration.
The operation noise and air flow expelled shall not affect
neighbors.
No flammable gas is leaked nearby.
It is convenient for piping and wiring.
If it is installed in indoor space,it might cause indoor temp
declined and noise disturbance, Please take preventive
measures for this.
If the unit need to be installed on a metal holder, make sure
they are insulated well and in accordance with local standard.
CAUTION
Installing the equipment in any of the following places may
lead to malfunction of the equipment (if it is inevitable, consult
the supplier).
The site contains mineral oils such as cutting lubricant.
Seaside where the air contains much salt.
Hot spring area where corrosive gases exist, e.g., sulfide gas.
Factories where the power voltage fluctuates seriously.
Inside a car or cabin.
Drain condensate water
1
Adaptor

3
Installation & Owner‘s Manual
Place like kitchen where oil permeates.
Place where strong electromagnetic waves exist.
Place where flammable gases or materials exist.
Place where acid or alkali gases evaporate.
Other special environments.
Precautions before installation
Decide the correct way of conveying the equipment.
Decide the correct way of conveying the equipment.
If the unit has to be installed on a metal part of the building,
electric insulation must be installed, and the installation must
meet the relevant technical standards for electric devices.
Installation space
Before installing the unit, reserve the space of maintenance
shown in the following figure.
Fig.3-1
Fig.4-1
Display
Fig.3-2
WARNING
4. INSTALLATION
Ask your supplier to install the air source heat pump water
heating units. Incomplete installation performed by yourself may
result in a water leakage, electric shock, or fire.
The place without direct sunlight and other heat supplies. If
there’s no way to avoid these, please install a covering.
The unit must be securely fixed, or else, noise and shaking will
be resulted.
Make sure that there’s no remora around the unit.
In the place where there is strong wind like seashore, fix the unit
in the location protected from the wind.
Carry the unit onto the site
In order to avoid scratch or deformation of the unit surface,
apply guard boards to the contacting surface.
No contact of fingers and other things with the vanes.
Don’t incline the unit more than 45° in moving, and keep it
vertical when installing.
This system is very heavy, it need to be carried by 2 or more
persons, othewise might cause injury and damage.
Install the unit.
The circulating air for every unit should be more than 700m3/h.
Make sure there is enough Installation space.
Outline dimensional drawing(see Fig.4-1,Fig.4-2)
Air outlet
Barrier
≥600mm
≥600mm
≥600mm
≥600mm
≥800mm
≥600mm
1920 mm
Air inlet
650 mm

4
Installation & Owner‘s Manual
Fig.4-2
5. PIPELINE CONNECTION
Fig.5-1
Pipeline Connection Sketch
Pipeline Connection Explanation
Installation of the water inlet or outlet pipes: The spec of the
water inlet or outlet thread is
RC3/4” ( internal thread). Pipes
must be
heat-resistant and durable.
Installation of the pipe for PT valve: The spec of the valve
connecting thread is
RC3/4” ( internal thread). After installation,
it must be confirmed that the drainpipe outlet is exposed in the
air. When flexible drainpipe is jointed to the pressure relief
orifice of this valve, it must be confirmed that the flexible
drainpipe is downwards vertically and exposed in the air.
CAUTION
NOTE
●Do not press the handle of PT Valve,
●Do not dismantle the PT Valve,
●Do not block off the Drainage pipe,
It will cause explosion and injury,if do not comply with the
above instruction.
EXPLOSION
Handle
Drainage
pipe
Installation of the One Way Valve: The spec of the One Way
Valve thread in accessories is RC3/4”. It is used to prevent
backflow of water.
Installation of the Y-shaped filter: The spec of the Y-shaped
filter thread in accessories is RC3/4”. It is used to filtrate inlet
water.
After all the pipes installed turn on the cool water inlet and hot
water outlet and start effusing the tank. When there is water
normally flowing out from water outlet, the tank is full. Turn off
all valves and check all pipes. If there is any leakage, please
repair.
If the inlet water pressure is less than 0.15MPa, a pressure
pump should be installed at the water inlet.
For guarantee the long safety using age of tank at the
condition of water supply hydraulic higher than 0.65MPa, a
reducing valve should be mounted at the water inlet pipe.
Probably may cause water leakage because of blockage
during the drainage, pit is suggested to use a water collector
as instruction in Fig 5-2.
Fig.5-2
50mm larger than
the dia. of HPWH
Max.22mm
A safety valve should be installed at the water inlet of the unit.
Arrange water pipes and which connected fittings as illustration
of the above figure. In case of install it at a place where outside
temperature below freezing point, insulation must be provided for
all hydraulic components.
The handle of PT Valve should be pulled out once per half year,
to make sure that there is no jam of the valve.
Please beware of burn, because of the high
temperature of water. The drainage pipe should
be well installed ,in order to avoid
freezing up in cold weather.
Water Outlet
User
water Inlet
Anode rod
Drainpipe
Tap Water
Ball Valve
OneWay Valve
Y-shaped Filter
Barrel-drain
Thermal expansion tank
(if required)
PT Valve
Upper
Condensate Outlet
Lower
Condensate Outlet
Notice:
the mixer tap is required
on the hot water usage
terminal
Solar sensor
Solar water inlet
Solar water outlet
650 mm
Heat Pump
Water Heater
When install the main unit, please set a drain valve at the drain
orifice of the unit by self.

5
Installation & Owner‘s Manual
≤2
≤2
≤10
≤10
≤2
≤2
≤5
≤5
Straight-line length (m) Bent pressure drop(Pa)
Bent’s qty.
Straight-line pressure drop (Pa/m)
190mm
190mm
6. DUCT CONNECTION WAY
Air inlet without canvas , air outlet connect to canvas.
Air inlet and outlet no need to connect with canvas
Air inlet and outlet need to connect with canvas.
Canvas Duct Description
Air inletAir outlet
Air inletAir outlet
Air inlet
Air outlet Air inletAir outlet
A+B≤10m
A≤10m
A≤10m
Recommending: Use it in where with surplus heat or
indoor place in the winter where with surplus heat.
Recommending: In summer, use this connection way
could charge flesh air into room.
A B
A
A
Note: Upon connect canvas, portion airflow and
capacity in heat pump system will lose in the system.
Fig.6-1 Fig.6-3
Fig.6-4
Fig.6-2
Air inlet connect to canvas, air outlet without canvas.
Canvas Duct
Round canvas duct
Rectangle canvas duct
Other shaped canvas duct
Φ190
190X190
Refer to above data
Dimension(mm)
Note: Canvas duct to be connected at air outlet better than at inlet.

6
Installation & Owner‘s Manual
The power supply for the unit must be specialized according
to the rated voltage.
Earthing must be included in the power circuit. And it must be
connected with the effective external ground wire.
The wiring must be performed by professional technicians
according to the circuit diagram.
Set the electric leakage protector according to the relevant
electric technical standards of the State.
The power cord and the signal cord shall be laid out neatly
and properly without
mutual interference or contacting the
connection pipe or valve.
After wire connection is finished, check it again and make
sure the correctness before supplying power .
CAUTION
7. ELECTRIC CONNECTION
NOTE
Upon connect canvas, portion airflow and
capacity in heat pump system will lose in the system.
For main unit air outlet connects with canvas, when main unit
operating, condensate dew be generates at the outside of air
outlet canvas. Please pay attention to the discharge of conden-
sate water. We suggest you to wrap the thermal insulated layer
at the outside of air outlet canvas.
For the case of main unit connect with canvas, the diameter of
the duct must ≥190mm, total length of the ducts should not
longer than 10m or the maximum static pressure should not
exceed than 50Pa. Be in mind of the bending site of the duct no
more than 5.
Filter installing at the main unit inlet. In terms of the main unit
connect with canvas, filter in there must be put forward to the
air inlet of duct. (Fig.6-7/6-8)
To fluently drain condensate water from evaporator, please install
the main unit at a horizontal floor. Otherwise, please ensuring the
drain vent is at the lowest place. Recommending the inclination
angle of unit to the ground should no more than 2°.
Fig.6-5
Fig.6-6
Main unit
Rain
Recommending install the main unit at indoor ambient. It is not
allow to install the unit at outdoor or rain achieving place.
Warning: In case of rain entering to internal components of the
main unit, the component might be damaged or causing
physical danger.(Fig.6-5)
In terms of the main unit connect with canvas reaching to
outdoor, a reliable water-resistant measure must be conduct on
the duct, resist water drop into internal of the main unit.(Fig.6-6)
≥2.5D
ΦD
Rain
Weather shed
Fig.6-7 Fig.6-8
Fig.6-9 Fig.6-10
Filter
Filter
inletoulet
Owner should install
the filter by self; and
the mesh size is
about 1.2mm.
Drain Drain
≤2
o

7
Installation & Owner‘s Manual
Table. 7-1
7.1 Specifications of Power Supply
RSJ-35/300RDN3-B
4
15/5
30 mA
≤
0.1sec
Creepage Breaker
Earth Wire(mm2)
Manual Switch(A) Capcity/Fuse
Model Name
Power Supply
MIin. Diameter of Power
Supply Line
(mm2)
220-240V～50Hz
4
Fig.7-1
7.2 Electric Wiring Illustration
T3: Tube Temp. Sensor
T4: Ambient Temp. Sensor
T5U: Tank Temp. Sensor (upper)
TP: Discharge Temp. Sensor(upper)
Earthing
T5L:
Tank Temp. Sensor (lower)
NO NO
L N
G
T3
T5U
T5L
T4
TP
220-240V～
50 Hz
T4
N1
1
2 4
3
CC
G-B
G-A
G-C
G-D
G-E
Compressor
Compressor
Main Control Board
Electric Heater
Electric Heater
Pressure Switch
TCO
Control Panel
TOD
TH
TH: Return air temperature sen
WARNING
Just to be on the safe side, the unit must be installed an
Creepage Breaker
near the power supply and must be effectively
earthed.
Please choose the power cable according to above table, and
it should comply with local electric standard.
The power cord type designation is H05RN-F.

8
Installation & Owner‘s Manual
CAUTION
CAUTION
After powered on, the display lights up. Users can operate the unit through the buttons
under the display for different modes
Emptying: If the unit needs cleaning, moving etc, the tank should be emptied.
Method: See Fig.8-2:
8.1 Operation steps
8. OPERATING INSTRUCTION
Fig.8-2
Operation without water in water tank may result in
damage of auxiliary e-heater. Due to such damage, the
supplier is not responsible for the quality issue.
Over 50℃may result in serious burn or so caused death.
Special care should be paid to the children, the disabled and
the old in case of water burn.
Water Affusion
Hot water outlet
Close
Water out
When water flows out from the water
outlet, the tank is full. Turn off the hot
water outlet valve and water affusion
is finished.
Open
Open the cool water inlet and
hot water outlet
Cool water inlet Hot water outlet
Open
Fig.8-1
Emptying
Close
Open
Drainpipe
Open
Cool water inlet
Close the cool water inlet, open the hot
water outlet and open drainpipe.
Hot water outlet
Drainpipe
Close
After emptying, please replace the nut of
drainpipe.
Before using this unit, please follow the steps below.
Water Affusion: If the unit is used for the first time or used again after emptying the tank, please make sure that the
tank is full of water before turning on the power.
Method: see Fig.7-1

9
Installation & Owner‘s Manual
8-2 Operation steps
1 Control Panel Explanation
2 Display Explanation
Fig.8-3
Display
Operation
ECONOMY MODE
ALARM
FILL WATER
HIGH TEMP
TIME ON TIME OFF TIMER
CONFLICT
TEMP-SET
OUTLET TEMP
HYBRID MODE
E-HEATER MODE
ON\OFF
CLOCK
CANCEL MODE
TIME
ON
Fig.8-4
① ② ③
⑤
④
⑧
⑦
⑩ ⑨
⑥
1 1 1 2 1 3
1 4
1 5
1 6
HIGH TEMP indicator:When the setting temp. exceeds
50
℃ , it lights up to remind you that the outlet temp. is
too high for direct spray.
FILL WATER indicator: When the power supply is turned
on, it lights up to remind you to re-affuse water.
ALARM indicator: It will flashing at the malfunction or
protection time.
TEMP-SET indicator: Show the setting temperature and
blank when screen protection. Codes are show at the
malfunction or protection time
LOCK indicator : When the UI is locked, it always lights.
②
①
③
④
⑤
Table.8-1
Water temp. indicator: When the actual water temp.
exceeds 60 ℃ , it lights up.
Water temp. indicator: When the actual water temp.
exceeds 40
℃ , it lights up.
OUTLET TEMP indicator: It displays water temp.
of the upper part of the tank, which can be used.
It always lights.
TIMER CONFLICT indicator: When the temp you
set through Wired Controller conflicts with that
through User Interface, it lights up.
TIME OFF indicator: It will light up when timing off mode
is setted, blanks when screen protection.
TIME ON indicator: It will light up when timing on mode
is setted, blanks when screen protection.
CLOCK indicator: It displays present time
, it will blanks
when screen protection.
E-HEATER MODE indicator: When user sets the
E-heating Mode, it lights up.
HYBRID MODE indicator: When user sets the Hybrid
Mode, it lights up.
ECONOMY MODE indicator: When user set the
Economy Mode, it lights up.
⑧
⑨
⑩
1 1
1 2
1
3
1 4
1 5
1 6
3 Operation
Fig.8-5
Preparation before running the unit.
When you run the unit for the first time, all the indicators on the
UI will light for 3 second, and the buzzer will “didi” ring twice at
the same time, and then, display the fiducial web page. After no
operation for 1 minute, all indicators will go out automatically
except Water fill indicator flashing and tank’s temp. indicator
lighting. Buzzer will “di” ring when you press it.
When the tank is full, please press the ON\OFF key, the Water
fill indicator will stop flashing and you can continue to function
other settings. When all settings finished, please press the
ON\OFF key again and the Water fill indicator will go out. And
then run the unit.
When the unit is running, if there is no operation or malfunction
for 20s, the backlight of the display will go out automatically
except operation model,outlet temp,lock indicator .
If there no operation for 1min, the unit will lock automatically.
but the lock indicator would be right all time.
4 Operation Instruction
ON\OFF
CLOCK
CANCEL MODE
ON\OFF key,
used to turn the
unit on or off
CLOCK key,
used to set
time.
CANCEL key,
used to cancel
timer and lock
MODE key,
used to set
different modes
TIME OFF key,
used to set the
OFF timer
UP key,
used to add
time or temp.
DOWN key,
used to abate
time or temp.
TIME ON key,
used to set the ON
timer
ECONOMY MODE
ALARM
FILL WATER
HIGH TEMP
TIME ON TIME OFF TIMER
CONFLICT
TEMP-SET
OUTLET TEMP
HYBRID MODE
E-HEATER MODE
TIME
OFF
TIME
ON TIME
OFF
LOCK
LOCK
⑥
Water temp. indicator: When the actual water temp.
exceeds 50
℃ , it lights up.
⑦

10
Installation & Owner‘s Manual
Fig.8-6
Lock and Unlock
In order to prevent wrong operation, a special lock function has
been designed. If there is no operation for 1min, the unit will be
locked automatically, and display the lock indicator .
When the unit is locked, no keys can be operated.
Unlock:
Clock Set
The clock is for a 24-hour system and the initial time is 00:00.
To make a better use of this unit, it is recommended to set the
time for accurate local time. Every time powered off, the clock
will be reset to the initial time 00:00.
Method for time set
CANCEL
At the locking status of Display, long press
the “cancel” key to remove it.At the screen
protection of Display, press any key to
active the Display, and then long press the
“cancel” key to remove it.After remove the
locking mode, the lock indicator will blank
out, all keys could be used normally.
CLOCK
Press the CLOCK key, the minute digit of
the clock on the display starts flashing
slowly.
CLOCK
Press the CLOCK key again, the minute
digit stops flashing while the hour digit
starts.
Press the “UP” and “DOWN” key, you can
adjust the minute.
Press the “UP” and “DOWN” key, you can
adjust the hour.
Fig.8-7
Press “CLOCK” key again or stop operation
for about 10s, flashing will stop and clock
set is successful.
Fig.8-8
Mode Selection
The unit is enhanced with three operation modes, Economy
Mode, Hybrid Mode and E-heater Mode.
Economy Mode: The unit heats water only by compressor drive
according to heat-pump principle. Used when the ambient
temp. is high.
Hybrid Mode:The unit heats water not only by compressor drive
but also by electric heater.Used when the ambient temp. is low
or large amount of hot water is needed.
E-heater Mode:The unit heats water only by electric heater.
Used when the ambient temp. is very low.
By default, the unit operates in Hybrid Mode.
Change:
MODE
Press the MODE key, operation mode will
be shifted among the three modes in a
cycle, meanwhile the corresponding
indicator on the display will light up.
Temp. Set
Temp displayed is the water temp. in the upper part of the tank.
Default is 65℃and the Economy mode setting range is 38~60
℃,the Hybrid and E-heater mode setting range is 38~60℃.
Method for set

11
Installation & Owner‘s Manual
Fig.8-9
Fig.8-10
Press the “UP” and “DOWN” key, you can
Increase or decrease the water temp.
When the set temp. is higher than 50 ℃,
the HIGH TEMP indicator will light.
HIGH TEMP
Timer
User can set up a running start time and a stop time on a
specifically by the timer function.
tenminutes.
Time on: User can set up a start time by this. The unit will auto
run one time between the set time and 24:00 on the same day.
Method for set
Fig.8-11
Fig.8 -12
Cancel:
CANCEL
In the unlocked state, press the CANCEL
key 1s and the time on function will be
canceled.
Press the TIME ON key again and wait
about 10s, flashing stops and ON TIMER
set is finished.
TIME
ON
Press the TIME ON key, the minute digit
of the clock on the display starts flashing
slowly.
Press the TIME ON key again, the minute
digit stop flashing and the hour digit starts.
Press the “UP” and “DOWN” key, you can
adjust the minute.
Press the “UP” and “DOWN” key, you can
adjust the hour.
The least numbers of timer is
Time on and Time off: Users can set up a running start time and
a stop time. When the start time is earlier than the stop time,
the unit will run between the set time. When the start time is
later than the stop time, the unit will run between the start time
today and the stop time next day,when user set up on a running
start time and a stop time at the same time, the stop time will be
delay ten minutes automatically.
Method for setting
TIME
ON
Press the TIME ON key, the minute digit
of the clock on the display starts flashing
slowly.
Press the “UP” and “DOWN” key, you can
adjust the minute.
TIME
ON

12
Installation & Owner‘s Manual
Press the TIME ON key again, the minute
digit stops flashing and the hour digit starts.
Press the “UP” and “DOWN” key, you can
adjust the hour.
CANCEL
In the unlocked state, press the CANCEL
key for 1s, the Time on and Time off
function will be canceled
Fig.8-14
Press the TIME OFF key, the minute digit
on the display starts flashing slowly.
Press the “UP” and “DOWN” key, you can
adjust the minute.
Cancel:
Stop operation for about 10s, flashing
stops and TIME ON+TIME OFF set is
finished.
TIME
OFF
Press the TIME OFF key again, the minute
digit stops flashing and the hour digit starts.
Press the “UP” and “DOWN” key, you can
adjust the hour.
Fig.8-13
ON\OFF
NOTE
Time on and Time off can not be set to the same time. If they are
the same, the stop time will delay 10 minutes automatically.
For example, Time on and Time off set to 1:00 at the same
time,then the stop time will adjust to 1:10 automatically.
Time off function can not be used alone. The key can be used
only after setted the on time.
User can press the on\off key manual beyond the timer range.
Power On and Power Off
Press Power On/Power Off button after all the above have
finished and the system will run as the setting. And simply
press the same button to stop it.
Fig.8-15
Operation status
The LA code from the screen of set Temp. will appear and
remind user when ambience temp. not meet the operation
condition of heat pump unit(beyond -7～43℃)，User can sw-
itch the economy mode to E-heating mode in sure of enough
volume of hot water if need, The unit will return operation
pre-status automatically in no any operation when the ambie-
nce temp. meet the operation condition of heat pump mode
and the error LA will be disappear at the same time,the
screen display nomally.
TIME
OFF
TIME
ON

13
Installation & Owner‘s Manual
WARNING
The covers of the E-heater should not be opened
without guidance of professional technician, in case
of electric shock or any danger.
Fig.8-16
Fig.8-17
Warning Code of disagree
with heat pump mode
TEMP-SET
The light will glitter in error
ALARM
Warning Code of disagree with
heat pump mode
Temp.Set
Fig.8-18
Error Shooting
If some errors happen, the buzzer will buzz 3 times every other
minute and the ALARM indicator will glitter fast. Press CANCEL
for several seconds to stop the buzzer but the light will keep
glittering.
The light will glitter in error
ALARM
CANCEL
CANCEL
Press CANCEL key to stop the buzzer.
Fig.8-19
The error code from the screen of set Temp. will display when
malfunction happen,the system display error code after one
minute when press the key again and the screen display set
temp.
When the economy mode happen malfunction,the system can
keep using after switching to E-heater mode;When some error
happens, though the system could be used in some circum-
stances, it could not reach the expected efficiency. Please
contact your supplier for help.
Error Code Explanation (See t
able.8-20 )
Fig.8-20
Display the error code
TEMP-SET
In case of continual 20 hours when in the season ambient
temperature doesn’t meet for the heat pump operation
requirement (absent from the range -7~43℃) , “LA” will display
at Temp. Settings window and ALARM indicator flashing
simultaneously alarming that the temperature doesn’t suit for
heat pump performance, only E-heating mode could be set at
such circumstance. Please switch to E-heating mode manually
for ensuring there‘s adequate hot water could be supplied, if
that so code is going to disappear and indicator alarm stop
flashing any more , all recover to be normal.

14
Installation & Owner‘s Manual
Display
E0
E1
E2
E4
E5
E6
E7
E8
P2
P3
Malfunction Description
Error of sensor T5U
Error of sensor T5L
Tank and Wired Controller communication error
Evap. pipe temperature sensor error
Ambient temperature sensor error
Discharge pipe temp.sensor error
Heat Pump system error
Electric leakage protection
Discharge pipe temperature overhigh protection
No current flowing in Compressor
Table.8-2
P4
P8
P9
Compressor overloaded protection
Upper e-heater overloaded protection
If the errors happen, please contact the supplier or after-sale
service.
Ambient temp. is not fit for heat pumps,change the
mode to E-heater mode
LA
Before running, please check the following items first:
Correct installation of the system;
Correct connection of pipeline and wiring;
Leakage of the refrigerant pipeline tested;
Efficient drainpipe;
Complete insulation protection;
Correct earthing;
Correct power supply;
No obstacle outside the air inlet and outlet;
No air in the water pipeline and all valve opened;
Effective electric leakage protector;
Sufficient inlet water pressure(≥0.15MPa)
Water-heating Operating Capability
Heating elements are included in the unit, one heat
pump and one electric heaters and solar coil. All these three
heating elements do not work together.
This unit has two temp. sensors, which are installed at the
upper 1/4 and bottom 1/2. The upper one tests the upper temp.,
the figure shows in the water temp. table, and the bottom one
is used to test the lower water temp., which will control the ON &
OFF of the unit, no shows in the display panel.
Economy Mode: In this mode, according to the water tempera-
ture setting, heat pump in preference to electric heater.
(Water
outlet temp. range 38～60 ℃ ,running ambient -7～43 ℃)
Hybrid Mode: In this mode, the system will adjust the working
capabilities of e-heater and heat pump according to the tank
water temperature.
(Water outlet temp. range 38～60 ℃ ,running ambient -30～43 ℃)
9. RUNNING AND CAPABILITY
9.1 Trial Running
9.2 Operating Capability
Tank Coil
Upper sensor
Bottom sensor
electric heater
Inlet
outlet
Fig.9-1
No current flowing in electric heater
P3
P1 System high pressure protection
P2
E9 TH sensor condenser failure

15
Installation & Owner‘s Manual
Water Temperature Display
The temperature on the display is the water temperature in
upper part of water tank (over 1/4) which you will use, but not
that of all the water.
The 6 indicators beside the water temperature on the display
are the lower part water temperature. When the temperature is
higher than 40℃, the blue one will light up; when higher than
50℃, the blue and yellow ones light up; when higher than 60℃
, the blue, yellow and red ones light up and when all light up,
the water temperature has reached the set point.
In water using, the temperature of the lower part may decrease
while the upper part still keeps a high one, and the system will
start heating the lower part. And it is normal.
Error Shooting
When common error happens, the system enters Standby
Mode and could still work, but not so efficient as normal. Please
contact the technician.
When serious error happens, the system will be unable to carry
on. Please contact the technician.
When error happens, the buzzer will buzz in every other
minute, the Warning light glitter and the display indicate the
error code and water temperature alternatively. Press CANCEL
button for 3sec to stop the alarm.
Restart after Long Stop
When the system is started after a long time (trial running
included), it is normal if the outlet water is unclean. Keep the
tap on and it will be clean soon.
NOTE
This mode should be used at the ambient temperature
maintaining at -7～43℃. While the ambient temperature below
than -7℃, the energy efficient would bocome low obviously, we
recommend you to using the E-heat mode at this circumstance.
NOTE
In the E-heat mode, only half tank of water, i.e. 150L, could be
heat every time.
E-heater Mode: In this mode, the compressor and the fan motor
will not run but the e-heater work only.
(Water outlet temp. range 38～60 ℃ ，running ambient -30～43
℃).
Defrosting during Water-heating
In the Economy Mode and Hybrid Mode, if the evaporation
frosts in a cold circumstance, the system will defrost automati-
cally to keep effective performance(3~10 min).
Ambient Temperature
The system’s operation temperature is within -30~43℃and
below are the operation temperature for each mode.
Economy Mode: -7~43℃
NOTE
When self-protection happens, cut the power supply manually
and restart after the error resolved.
Hybrid Mode: -30~43℃
E-heater Mode: -30~43℃
Mode Selection
Different mode is designed to meet different demand and the
following are recommended selections.
Economy Mode:-7~43℃, a continuous hot water demand below
250L(60℃);
Hybrid Mode: -30~43℃, a continuous hot water demand
between 300L~350L(60℃);
E-heater Mode: -30~43℃, a continuous hot water demand
between 150L(60℃).
Self-Protection Apparatuses
When the self-protection happens, the system will be stopped
and start self-check, and restart when the protection resolved;
When the self-protection happens, the buzzer will buzz in every
other minute, the ALARM indicator glitter and the display
indicate the error code and water temperature alternatively.
Press CANCEL button for 3sec to stop the alarm. All stop when
the protection is resolved and error code disappears on the
display.
In the following circumstances, self-protection starts:
Air inlet or outlet is obstacled;
The evaporation is covered with too much dust;
Incorrect power supply (exceeding the range of 220-240V)
②
①
③
1)
2)
3)

16
Installation & Owner‘s Manual
10. MAINTENANCE
Check the connection between power supply plug and socket
and ground wiring regularly;
In some cold area (below 0℃), if the system will be stopped for
a long time, all the water should be released in case of freezing
of inner tank and damage of e-heater.
It is recommended to clean the inner tank and e-heater
regularly to keep an efficient performance.
Check the anode rod every half year and change it if it has been
used out. For more details, please contact the supplier or the
after-sale service.
It is recommended to set a lower temperature to decrease the
heat release, prevent scale and save energy if the outlet water
is sufficient.
Clean the air filter every month in case of any affect on the
heating performance.
In terms of the filter set in air inlet directly (namely, air inlet
without connect with canvas), the method of dismantle the filter
is: anti-clockwise unscrew the air inlet ring, take out the filter
and clean it completely, finally, remount it to the unit.
Before shutting the system down for a long time, please:
Shut down the power supply;
Release all the water in water tank and the pipeline and close
all the valves;
Check the inner components regularly.
10.1 Maintenance
Turn off the power, and turn off the water inlet valve.
Open hot water tap, and decrease the pressure of the inner
container.
Open the temperature pressure valve, and drain out the water,
until there are no water flow out of .
Get off the anode rod according to instruction.
Replace with a new one, and make sure effective sealed.
Open cold water valve until hot water flows out, and turn off the
hot water tap.
Restart and can be used normally.
How to Change the Anode rod
3-min Protection
With the power supplied, an immediate restart after the shutting
down will have to wait 3 min as to protect the compressor.
If self-protection happens and the system stops, check :
When the power indicator lights up, if the system is forced to run
while startup requirement has not been met;
If the air outlet or inlet is jammed or strong wind blows to air
outlet.
Defrosting
When it is humid and cold, the evaporate may defrost and the
water-heating capacity decrease. And the system will stop
heating water and start defrosting and then restart water-
heating
During defrosting, fan stops working, four-way valve reverses
the flow direction, and compressor keeps working.
The defrosting time varies from 3min to 10min according to the
ambient temperature and the frost.
Temperature Display
When the system stops, a decrease of the temperature is
normal as heat released. When it decreases to some point, the
system will restart automatically;
During water-heating, the displayed water temperature might
still decrease or not increase for a period of time because of the
heat exchange of the water. When the whole tank of water has
reached the set temperature, the system will stop automati-
cally.
10.2 Non-error Malfunction
10.3 Malfunctions and Resolutions
10.4 After-Sale Service
Malfunction
Outlet water
is cold.
The display
is dark.
No hot
water from
the outlet.
Water
leakage
Cause Resolutions
Bad connection of power
supply plug and socket;
Outlet water is set an a low
temperature;
Outlet water temperature
controller is damaged;
Circuit board of indicating
indicator is damaged;
Tap water has been cut away;
Water pressure is too low;
Inlet valve has been closed.
The joints on the pipeline are
not sealed well.
Reconnect the
plug;
Set outlet water an
a higher
temperature;
Contact the
technician.
It’ll return to normal
after water supplied;
Use it when the
pressure is higher;
Open the inlet water
valve.
Check and reseal
all the joints.
If the unit runs to some malfunction or error, it should be shut
down and power supply cut off. And then please contact your
local service center or supplier for help.
Table.10-1