Munters Comm-Box Instruction manual

Manual for use and maintenance
CommBox
Internet Access
Ag/MIS/UmGb-2595-05/18 Rev 1.7
P/N: 116597
CommBox

© Munters AB, 2020 2
CommBox
Manual for use and maintenance
Document Revision: 1.7, 12/2021
Ag/MIS/UmGb-2595-05/18 Rev 2.0 (MIS)
Software Ver: 3.5.6
This manual for use and maintenance is an integral part of the apparatus together with the attached
technical documentation.
This document is destined for the user of the apparatus: it may not be reproduced in whole or in part,
committed to computer memory as a file or delivered to third parties without the prior authorization of the
assembler of the system.
Munters reserves the right to effect modifications to the apparatus in accordance with technical and legal
developments.

© Munters AB, 2020 3
Index
chapter page
1INTRODUCTION ------------------------------------------------------------------------------------------------------------------------------------------5
1.1 Disclaimer-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- 5
1.2 Introduction----------------------------------------------------------------------------------------------------------------------------------------------------------------------------- 5
1.3 Notes ----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- 5
2INTRODUCTION TO THE COMMBOX ------------------------------------------------------------------------------------------------ 6
2.1 Ordering ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- 6
2.2 What Comes in the Package --------------------------------------------------------------------------------------------------------------------------------------- 6
3HARDWARE INSTALLATION --------------------------------------------------------------------------------------------------------------------7
3.1 CommBox Ports-------------------------------------------------------------------------------------------------------------------------------------------------------------------- 7
3.2 Mounting the CommBox ------------------------------------------------------------------------------------------------------------------------------------------------ 8
3.3 Grounding------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- 8
3.4 Connecting the CommBox to the Internet------------------------------------------------------------------------------------------------------------- 9
3.5 Connecting the CommBox to a Peripheral Device------------------------------------------------------------------------------------------ 9
3.6 Connecting the CommBox to a Communicator------------------------------------------------------------------------------------------------ 9
3.7 Connecting the CommBox to a Controller or RLink------------------------------------------------------------------------------------- 10
3.7.1 Controller to Junction Box Connection....................................................................................... 10
3.7.2 Comm-Box to Junction Box Wiring .............................................................................................. 13
3.7.3 RLINK One Connection ................................................................................................................... 13
3.7.4 Wiring Topology ................................................................................................................................ 16
3.7.5 Termination ........................................................................................................................................... 16
3.7.5.1 Termination Topologies ................................................................................................................17
3.7.5.2 Termination Wiring .......................................................................................................................19
4TECHNICAL DATA------------------------------------------------------------------------------------------------------------------------------------- 20
5GROUP MANAGEMENT------------------------------------------------------------------------------------------------------------------------ 22
5.1 Activating the Group ----------------------------------------------------------------------------------------------------------------------------------------------------- 23
5.2 Log In -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- 24
5.3 Attaching the Farm to a Group ------------------------------------------------------------------------------------------------------------------------------- 25
5.3.1 No Existing Groups........................................................................................................................... 25
5.3.2 Groups Exist......................................................................................................................................... 25
5.4 Local Log In------------------------------------------------------------------------------------------------------------------------------------------------------------------------- 26
6ROTEMNET WEB--------------------------------------------------------------------------------------------------------------------------------------- 27
6.1 RotemNet Web Functionality------------------------------------------------------------------------------------------------------------------------------------ 28

© Munters AB, 2020 4
6.1.1 Farm Settings Tab............................................................................................................................... 28
6.1.1.1 Farm Settings.................................................................................................................................28
6.1.1.2 Push Notifications .........................................................................................................................29
6.1.1.3 Local Users....................................................................................................................................30
6.1.1.4 Data Collect ..................................................................................................................................30
6.1.1.5 Activity Log....................................................................................................................................31
6.1.2 House Scan Tab ................................................................................................................................. 31
6.1.3 Diagnostics Tab................................................................................................................................... 32
6.1.4 About Tab ............................................................................................................................................. 33
6.2 User Settings----------------------------------------------------------------------------------------------------------------------------------------------------------------------- 34
6.3 Software Upgrade ---------------------------------------------------------------------------------------------------------------------------------------------------------- 34
7WARRANTY------------------------------------------------------------------------------------------------------------------------------------------------- 37

© Munters AB, 2020 5
1Introduction
1.1 Disclaimer
Munters reserves the right to make alterations to specifications, quantities, dimensions etc. for production
or other reasons, subsequent to publication. The information contained herein has been prepared by
qualified experts within Munters. While we believe the information is accurate and complete, we make no
warranty or representation for any particular purposes. The information is offered in good faith and with
the understanding that any use of the units or accessories in breach of the directions and warnings in this
document is at the sole discretion and risk of the user.
1.2 Introduction
Congratulations on your excellent choice of purchasing a CommBox!
In order to realize the full benefit from this product it is important that it is installed, commissioned and
operated correctly. Before installation or using the unit, this manual should be studied carefully. It is also
recommended that it is kept safely for future reference. The manual is intended as a reference for
installation, commissioning and day-to-day operation of the Munters equipment.
1.3 Notes
Date of release: July 2019
Munters cannot guarantee to inform users about the changes or to distribute new manuals to them.
All rights reserved. No part of this manual may be reproduced in any manner whatsoever without the
expressed written permission of Munters. The contents of this manual are subject to change without notice.

© Munters AB, 2020 6
2Introduction to the CommBox
CommBox provides complete access to your Munters controllers, including monitoring and control
capabilities, from any device, anywhere. From one computer, tablet, or smartphone, you can manage an
entire network.
•Cloud-based access to controllers
oMultiple, simultaneous users have network access
•Multiple communication pathways
oBuilt-in internet and telephone connectivity
oCellular Connectivity
•Local communication via wired or wireless communication
•Status reports provide critical information on house functions and animal statistics
•Push notifications
In addition, CommBox can act as an add-on for users wanting to add web-access to legacy
Communicator units.
2.1 Ordering
Each CommBox has one of two software packages:
•Poultry (P/N: 904-07-00016 CommBox-POU-EN-ROT)
•Pigs (P/N: 904-07-00017 CommBox-PIG-EN-ROT)
These software packages are not interchangeable and cannot be converted. In addition, connecting a
CommBox directly to a controller requires a Junction Box. There are two options:
•RS-232 Network: P/N 904-99-00036 COMMBOX -POU- JUNCTION BOX RS232
•RS-485 Network: P/N 904-99-00037 COMMBOX -POU- JUNCTION BOX RS485
2.2 What Comes in the Package
•CommBox
•Junction Box
•Power Supply Cables 115VAC and 230VAC
•EPROM for Communicator upgrade. When connecting CommBox directly to Communicator,
upgrade the Communicator software using the EPROM supplied.

© Munters AB, 2020 7
3Hardware Installation
This document details how to install Munters' CommBox unit. Installation consists of:
•CommBox Ports
•Mounting the CommBox
•Grounding
•Connecting the CommBox to the Internet
•Connecting the CommBox to a Peripheral Device
•Connecting the CommBox to a Communicator
•Connecting the CommBox to a Controller
NOTE No software installation is required.
3.1 CommBox Ports
Number
Description
1 On/off button
2 SIM Card port (4G card can be used with a modem for cellular connectivity)
3 HDMI port (refer to Connecting the CommBox to a Peripheral Device)
4 USB ports( refer to Connecting the CommBox to a Peripheral Device)
5 Internet ports (refer to Connecting the CommBox to the Internet)
Figure 2: Rear View

© Munters AB, 2020 8
Number
Description
1 & 2 External box cable connectors
3 Audio out
3.2 Mounting the CommBox
•Using the screws provided, mount the unit.
3.3 Grounding
•Connect the ground cable to the dedicated ground terminal.
CAUTION The CommBox must be grounded at all times!

© Munters AB, 2020 9
3.4 Connecting the CommBox to the Internet
•Connect the CommBox to your Internet connection/modem.
3.5 Connecting the CommBox to a Peripheral Device
If required, connect a screen or mouse to the CommBox (via the USB/HDMI ports).
NOTE Connect the screen to the CommBox using an HDMI cable only. Do not use any other type of
cable and an HDMI adapter.
3.6 Connecting the CommBox to a Communicator
•Connect the CommBox to a Munters Communicator a standard USB cable (supplied with the
Communicator unit).

© Munters AB, 2020 10
NOTE Communicator requires the Communicator Serial Card (P/N: C-COMM-SERIAL) to support the
CommBox. Refer to Document #112189 for details on upgrading the Communicator.
3.7 Connecting the CommBox to a Controller or RLink
The only step in installing a CommBox that requires wiring is if the CommBox is connected directly to a
controller (instead of a Communicator). In this situation the CommBox must be wired to the controller
communication card, via the Junction Box.
•Controller to Junction Box Connection
•RLINK One Connection
•Comm-Box to Junction Box Wiring
•Wiring Topology
•Termination
WARNING!
Disconnect the power before beginning!
WARNING!
Only an authorized electrical technician may perform this procedure!
3.7.1 CONTROLLER TO JUNCTION BOX CONNECTION
In the controller, connect the CommBox to the controller's communication card. Refer to the following
illustrations.

© Munters AB, 2020 11
1. Connect the wiring as follows:
•COM to COM
•The CommBox TX port is
connected to Controller's RX
port.
•The CommBox RX port is
connected to Controller's TX
port.
2. The cable between the CommBox
and the controller should be a 3
Wire Shielded Cable (22 AWG
minimum).
3. Connect the cable shield wire to
the controller ground strip.
Figure 3: RS-232 Wiring

© Munters AB, 2020 12
1. The cable between the
external connection box and
the controllers should be a 3
wire twisted shielded cable
(22 or 24 AWG).
2. Connect the wiring as
follows:
•COM to COM
•The CommBox A port
is connected to
Controller's A port.
•The CommBox B port
is connected to
Controller's B port.
3. The final controller in any
chain or branch requires a
120 ohm terminator. Refer to
Termination, page 16.
4. Connect the cable shield
wire to the controller ground
strip.
Figure 4: RS-485 Wiring

© Munters AB, 2020 13
3.7.2 RLINK ONE TO JUNCTION BOX WIRING
1. The cable between the external
connection box and the controllers should
be a 3 wire twisted shielded cable (22 or
24 AWG).
2. Connect the wiring as follows:
•COM to COM
•The CommBox A port is
connected to Controller's A port.
•The CommBox B port is
connected to Controller's B port.
3. The final controller in any chain or
branch requires a 120 ohm terminator.
Refer to Termination, page 16.
4. Connect the cable shield wire to the
controller ground strip.
5. Connect the wiring according to the
following table:
Port Color Wire
COM Brown
TX Green
RX White
+ Red
- Black
COM Shield wire
Figure 5: RLink OneWiring
NOTE: RLINK One supports RS-485 infrastructure only.

© Munters AB, 2020 14
3.7.3 COMM-BOX TO JUNCTION BOX WIRING
The Comm-Box comes with the power supply wired to the unit. See Figure 5.
Figure 6: Comm-Box power supply wiring
1. Insert the Junction Box 9-Pin Connector into COM1 (Figure 6).
Figure 7: Insert 9 Pin Connector
2. Insert the two wires coming from the Junction Box cable into the ports (Figure 7).

© Munters AB, 2020 15
Figure 8: Junction Box Wiring to Comm-Box
Table 1: Wiring Details
Cable source
Color
Function
Number
Junction Box Cable Red +VCC (24 DC) 1
Black -VCC (Junction Box) 2
Power Supply Cable White +VCC (Junction Box)
(24 DC)
3
Black -VCC 4
Black Ground 5
*These wires come preconnected to the Comm-Box. In the event that they need to be reattached, place
the white cable (#3) in the port as shown in Figure 7. Place both black cables into the ports as shown in
Figure 7; either cable can be placed in either port.
Figure 9: Power Supply – Comm-Box – Junction Box Setup

© Munters AB, 2020 16
3.7.4 WIRING TOPOLOGY
When connecting the CommBox to controllers via an RS-485 infrastructure, use one of the following
allowed topologies to ensure signal integrity.
Figure 10: Direct connections
Figure 11: T-Junction (permitted)
Figure 12: T-Junction (not permitted)
NOTE: When using RS-232, there is no restriction on the distance between the T-Junction and the
controller.
3.7.5 TERMINATION
Termination, installing 120 ohm termination resistors at the beginning and end units of each chain of
CommBox and controllers, ensures reliable communication in RS-485 infrastructures. The following
illustrations show where to install the resistors. Depending on the topology, install the resistors in the T-box,
the terminal controller, or the Munters Repeater.
•Termination Topologies
•Termination Wiring

© Munters AB, 2020 17
3.7.5.1 Termination Topologies
Figure 13: Topology 1: CommBox/House Termination
Figure 14: Topology 2: House Terminiation
The following two topologies require Munters RS-485 Repeaters.
CAUTION Install the repeater within one meter of the CommBoxT-Box
Figure 15: House and Repeater Termination

© Munters AB, 2020 18
Figure 16: House and Multiple Repeaters Termination
Figure 17: RLink One and House Termination
NOTE When using an RLINK One, refer to the RLINK One Manual for detailed information on RLINK
One termination.

© Munters AB, 2020 19
3.7.5.2 Termination Wiring
•CommBox: Install the termination resistor in the Junction Box.
Figure 18: Junction Termination
•Repeaters: Move the S2 dipswitch on the Output card to ON.
Figure 19: Repeater Termination

© Munters AB, 2020 20
4Technical Data
4.1 CommBox
Power Supply
Power Input •
24V DC +/-20%
•1 x 24V, 60W power adapter
CAUTION Unit shuld be powered by Limited Energy Source per IEC 61010-1 or Limited Power
Source per IEC 60950-1 or IEC 62368-1.
Temperature Range
Operating Temperature Range 0
°
to +50
°
C / 32
°
to 125
°
F
Storage Temperature Range -10
°
to +70
°
C / 14
°
to 158
°
F
Environmental Specifications
•
Indoor use only
•Altitude: -400 m to 2000 m
•Relative Humidity: 0 – 95%
•Main supply voltage fluctuation up to 5%
•Overvoltage category: OVCII
•Pollution degree: PD2
•Ingress Protection: IPXO
Housing
Metal Box Dimensions (W x H x D) 162 x 26 x 150 mm (without wall-mount bracket)
Certification
(Class A)