Alcatel-Lucent AOS-W 3.4 User manual

AOS-W 3.4
Quick Start Guide
0510546-01 | June 2009 1
This document describes the initial setup of an Alcatel-Lucent user-centric network that consists of an
Alcatel-Lucent switch and Alcatel-Lucent Access Points (APs). The installation consists of the following
steps:
1. Run the Java-based RF Plan tool, version 2.0 or higher, to determine the number of APs required for
your site. Alcatel-Lucent’s RF Plan is an application that allows you to determine AP placement
based on your specified coverage and capacity requirements without impacting the live network.
When you receive your APs, enter the serial number for each AP into the RF Plan tool.
Download the RF Plan tool and RF Plan Installation and User Guide from the Alcatel-Lucent
Technical Support web site at https://service.esd.alcatel-lucent.com
2. Use the Setup Wizard to configure the switch, install software licenses, and configure an internal
and a guest WLAN. For more information, see "Run the Setup Wizard" on page1
3. Connect the switch to the wired network.
For more information, see "Connect the Controller to the Wired Network" on page4
4. Ensure that the APs, when installed and powered on, will be able to locate and connect to the
switch.
For more information, see "Ensure APs Can Connect to the Controller" on page4
5. Define the mesh cluster profile, mesh radio profile, and provision the AP as a mesh portal or mesh
point when deploying APs in a mesh networking environment.
For more information, see "Provision APs for Mesh" on page5
6. Connect your APs to the network.
See "Install the APs" on page6
Before You Begin
1. Review the contents of your switch shipment to ensure that you have received the following:
Alcatel-Lucent switch with appropriate power cord and accessories
AOS-W 3.4 Quick Start Guide (this document)
AOS-W End User License Agreement
2. Read the AOS-W End User License Agreement.
Run the Setup Wizard
The Setup Wizard allows you to configure access to the switch, install software licenses, and configure
wireless local area networks (WLANs) for internal or guest users. The Setup Wizard is available the first
time you connect to and log into the switch or whenever the switch is reset to its factory default
NOTE
This step is required only if you are configuring mesh.
NOTE
Check the customer support web site for the latest software upgrades and documentation updates: https://
service.esd.alcatel-lucent.com.

2AOS-W 3.4 | Quick Start Guide
configuration. After you complete the Setup Wizard, the switch reboots using the new configuration
information you entered.
Required Information
Table 1 describes the basic information that is required for the Setup Wizard.
Optional Information
The Setup Wizard also allows you to:
zCreate virtual local area networks (VLANs) into which wireless users are placed after authentication
zModify default port settings
NOTE
Do not connect the switch to your network when running the Setup Wizard. The factory-default switch boots up
with a default IP address and both DHCP server and spanning tree functions are enabled. Once you have
completed the Setup Wizard and rebooted the switch, you can use either the CLI or WebUI for further
configuration before connecting the switch to your network.
Table 1 Prerequisites for the setup wizard
Requirement Description
System Name A user-defined name by which the Controller will be referenced. You can specify a name of up
to 63 characters.
Country Code The country in which the switch will operate. The country code determines the 802.11
wireless transmission spectrum.
NOTE: You cannot change the country code for controllers designated for certain countries,
such as the U.S. or Israel. Improper country code assignment can disrupt wireless
transmissions. Most countries impose penalties and sanctions for operators of wireless
networks with devices set to improper country codes.
admin Password Password of up to 32 characters for the admin user to log in to the switch.
Enable Mode
Password
Password of up to 15 characters for the admin user to access the Enable mode in the CLI.
Date and Time You can either manually set the date, time, and GMT time zone or specify the IP address of an
NTP server from which the switch will obtain its date and time settings.
Controller Mode zStandalone: If this is the only switch on the network.
zMaster: If this switch will manage other controllers on the network. You are prompted for a
key that will be used by all controllers on the network.
zLocal: If this switch will be managed by a master switch. You are prompted for a key that
will be used by all controllers on the network. (You need to provide the IP address of the
master switch.)
VLAN 1 The switch takes its IP address from VLAN 1. The switch uses the configured IP address to
communicate with other controllers and with APs.
Default Gateway This is usually the IP address of the interface on the upstream switch or router to which you
will connect the switch. The default gateway and the VLAN 1 IP address need to be in the
same network.
NOTE
These configurations are not available if you use a serial port connection to the switch to run an initial setup. See
“Serial Port Connection” on page 3.

AOS-W 3.4 | Quick Start Guide 3
zInstall licenses for AOS-W software modules
zConfigure internal and guest WLANs
Running the Setup Wizard
The default IP address of the switch is 172.16.0.254. When you connect a PC or workstation to a line port on
the switch, you can connect to this IP address through a Web browser to run the Setup Wizard.
You can use any PC or workstation on which you can run a Web browser. The system must either be
configured to obtain its IP address via DHCP or configured to have a static IP address on the 172.16.0.0/24
subnetwork.
To run the Setup Wizard:
1. Make sure that the switch is not connected to any device on your network.
2. Boot up the Alcatel-Lucent switch.
3. Connect your PC or workstation to a line port on the switch.
4. On your PC or workstation, open a Web browser and connect to https://172.16.0.254.
5. The switch contains a default server certificate. At the Security Alert, click Yes to proceed with the
Setup Wizard.
6. Enter the information described in Table 1.
7. Click Continue to install software licenses on the switch.
Proceed to "Connect the Controller to the Wired Network" on page4
Serial Port Connection
The serial port is located on the front panel of the switch. When you connect a terminal or PC/workstation
running a terminal emulation program to the serial port on the switch, you enter the Initial Setup dialog.
To run the Initial Setup dialog from a serial connection:
1. Configure your terminal or terminal emulation program to use the following communication settings:
2. Connect your terminal or PC/workstation to the serial port on the switch using an RS-232 serial cable.
All accessory kits shipped with Alcatel-Lucent controllers contain an RJ-45 cable and DB-9 to RJ-45
adapter for this purpose. You may need to provide a USB adapter to connect the serial cable to your PC.
NOTE
A digital certificate is a way to validate a device on the network. The default certificate installed in the switch does
not guarantee security in production networks. Alcatel-Lucent strongly recommends that you replace the default
certificate with a custom certificate issued for your site or domain by a trusted Certificate Authority. See the AOS-
W 3.4 User Guide for more information about certificates.
NOTE
The serial port connection allows you to configure the basic configuration required to connect the switch to the
network. The browser-based Setup Wizard allows you to also install software licenses and configure internal and
guest WLANs (see “Run the Setup Wizard” on page 1). If you use the Initial Setup dialog to configure the switch,
the Setup Wizard will not be available unless you reset the switch to its factory default configuration.
Table 2 Terminal Communication Settings
Baud Rate Data Bits Parity Stop Bits Flow Control
9600 8 None 1 None

4AOS-W 3.4 | Quick Start Guide
3. Boot up the Alcatel-Lucent switch.
4. Enter the information described in Table 1.
5. At the end of the Initial Setup, you are asked to review and confirm your configuration changes. Enter y
to accept the changes.
The switch reboots.
Proceed to "Connect the Controller to the Wired Network" on page4.
Connect the Controller to the Wired Network
Connect a port on the switch to the appropriately-configured port on a Layer-2 switch or router. Make sure
that you have the correct cables and that the port LEDs indicate proper connections. Refer to the
Installation Guide for your Alcatel-Lucent switch for port LED and cable descriptions.
Ensure APs Can Connect to the Controller
Before you install APs in a network environment, you must ensure that the APs will be able to locate and
connect to the switch when powered on. Specifically, you need to ensure the following:
zWhen connected to the network, each AP is assigned a valid IP address
zAPs are able to locate the switch
IP Addresses for APs
Each Alcatel-Lucent AP requires a unique IP address on a subnetwork that has connectivity to a switch.
Alcatel-Lucent recommends using the Dynamic Host Configuration Protocol (DHCP) to provide IP
addresses for APs; the DHCP server can be an existing network server or an Alcatel-Lucent switch
configured as a DHCP server.
If an AP is on the same subnetwork as the master switch, you can configure the switch as a DHCP server to
assign an IP address to the AP. The switch must be the only DHCP server for this subnetwork.
Using the WebUI to Enable DHCP Server Capability on the Controller
1. To use the WebUI, enter the IP address of the switch in the URL of a browser window.
2. At the WebUI login page, enter the admin user name and the password you entered during the Initial
Setup.
3. Navigate to the Configuration > Network > IP > DHCP Server page.
4. Select the Enable DHCP Server checkbox.
5. In the Pool Configuration section, click Add.
6. Enter information about the subnetwork for which IP addresses are to be assigned. Click Done.
7. If there are addresses that should not be assigned in the subnetwork:
NOTE
There are optional configurations you may want to complete before you connect the switch to your network, for
example, disabling spanning tree. In addition, you should set the system clock and install software licenses
before connecting to the network. For more information, see “Deploying a Basic User-Centric Network” in the
AOS-W 3.4 User Guide.
NOTE
The WebUI requires Internet Explorer 6.0. Other browsers may work but with limited functionality and are
therefore not supported.

AOS-W 3.4 | Quick Start Guide 5
a. Click Add in the Excluded Address Range section.
b. Enter the address range in the Add Excluded Address section.
c. Click Done.
8. Click Save Configuration at the top of the page to save this configuration to the switch’s flash
memory.
Controller Discovery
An Alcatel-Lucent AP can discover the IP address of the switch in one of several ways. The Aruba Discovery
Protocol (ADP) is enabled by default on all Alcatel-Lucent APs and controllers. To use ADP, all Alcatel-
Lucent APs and controllers must be connected to the same Layer-2 network.
With ADP, APs send out periodic multicast and broadcast queries to locate the master switch. If the APs are
in the same broadcast domain as the master switch, the switch automatically responds to the APs’ queries
with its IP address. If the APs are not in the same broadcast domain as the master switch, you need to
enable multicast on the network — see “Deploying a Basic User-Centric Network” in the AOS-W 3.4 User
Guide for information.
Provision APs for Mesh
Before you install APs in a mesh networking environment, you must do the following:
zDefine and configure the mesh cluster profile and mesh radio profile before configuring an AP to
operate as a mesh node. An AP configured for mesh is also known as a mesh node.
zProvision one of the following mesh roles on the AP:
Mesh portal—The gateway between the wireless mesh network and the enterprise wired LAN.
Mesh point—APs that can provide traditional Alcatel-Lucent WLAN services (such as client
connectivity, intrusion detection system (IDS) capabilities, user roles association, LAN-to-LAN
bridging, and Quality of Service (QoS) for LAN-to-mesh communication) to clients on one radio and
perform mesh backhaul/network connectivity on the other radio. Mesh points provides LAN-to-LAN
bridging through their Ethernet interfaces. It can now provide backhaul and access BSSIDs on the
same radio.
For detailed provisioning guidelines, caveats, and instructions, see the “Configuring Secure Enterprise
Mesh” chapter in the AOS-W 3.4 User Guide.
NOTE
If the devices are on different networks, a Layer-3 compatible discovery mechanism, such as DNS, DHCP, or
IGMP forwarding, must be used instead. See “Deploying a Basic User-Centric Network” in the AOS-W 3.4 User
Guide for information.
NOTE
The information in this section applies only if you are configuring and deploying APs in a mesh networking
environment. If you are not, proceed to "Install the APs" on page6.
NOTE
See Chapter 24, “Software Licenses” in the AOS-W 3.4 User Guide for license requirements.

6AOS-W 3.4 | Quick Start Guide
Install the APs
Use the AP placement map generated by RF Plan to install APs. You can either connect the AP directly to a
port on the switch, or connect the AP to another switch or router that has Layer-2 or Layer-3 connectivity to
the switch.
If the Ethernet port on the switch is an 802.3af Power over Ethernet (PoE) port, the AP automatically uses it
to power up. If a PoE port is not available, you need to obtain an AC adapter for the AP from Alcatel-Lucent.
For more information, see the Installation Guide for the specific AP.
Once an AP is connected to the network and powered up, it attempts to locate the switch using ADP.
On the switch, you can view the APs that have connected to the switch in the WebUI. Navigate to the
Configuration > Wireless > AP Installation page.
Figure 1 APs Connected to Controller
After you have installed a basic Alcatel-Lucent user-centric network, the Alcatel-Lucent AP advertises the
default aruba-ap SSID. Wireless users can connect to this SSID but because you have not yet configured
authentication, policies, or user roles, they will not have access to the network.
Chapter 5, “Configuring Access Points” in the AOS-W 3.4 User Guide describes how to configure APs. See
the other section and chapters in the AOS-W 3.4 User Guide for more information on configuring and using
features of the Alcatel-Lucent user-centric network.

AOS-W 3.4 | Quick Start Guide 7
Contacting Alcatel-Lucent
Copyright
© 2009 Alcatel-Lucent. All rights reserved.
Specifications in this manual are subject to change without notice.
Originated in the USA.
AOS-W, Alcatel 4308, Alcatel 4324, Alcatel 6000, Alcatel 41, Alcatel 60/61/65, Alcatel 70, and Alcatel 80 are trademarks of Alcatel-
Lucent in the United States and certain other countries.
Any other trademarks appearing in this manual are the property of their respective companies.
Legal Notice
The use of Alcatel-Lucent switching platforms and software, by all individuals or corporations, to terminate Cisco or Nortel VPN
client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full,
Alcatel-Lucent from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of
Cisco Systems or Nortel Networks.
Table 3 Alcatel-Lucent Contacts
Contact Center Online
zMain Site http://www.alcatel-lucent.com/enterprise
zSupport Site https://service.esd.alcatel-lucent.com
zEmail [email protected]
Service & Support Contact Center Telephone
zNorth America 1-800-995-2696
zLatin America 1-877-919-9526
zEurope [phone]
zAsia Pacific [phone]
zWorldwide 1-818-878-4507