Murideo MUR-MON-SING User manual

User's Manual Version 1.00
Murideo
Field Test Monitor
MUR-MON-SING
Page 1

Important Safety Information
•Follow all instructions
•Use only a dry cloth to clean
•Use caution not to block top vents on unit
•Indoor use only: To reduce the risk of electric shock, do not use near water or
expose to rain or moisture. Keep away from excess moisture
•Do not use near heat sources such as room heaters, hot A/V equipment
•Read all warnings
•Unplug the device during lightning storms or when unused for long periods of
time
•Keep away from open flames
•Protect all connected cords including power cords from being pinched,
compressed, and stepped on
•Do not open the case. All servicing should be done only by qualified and
approved service personnel and will void the warranty.
•Electrical Input Rating: Power over 12V/DC 1500mA.
oCaution: Use only the supplied AC/DC Adapter
•Operating temperature range: e.g. 0 to 40C.
•To disconnect power sources, remove the AC/DC adapter from the wall outlets.
Attention:
1. In order to protect your Field Test Monitor from possible damages, please do not
turn on the unit before HDMI cables are attached to the device. Please make sure
that connected source is completely powered off before you insert or extract
HDMI cables.
2. Please insert and extract HDMI cables from your Field Test Monitor gently and
with high level of care.
MUR-MON-SING
Page 2

MUR-MON-SING
Page 3

Thank you for purchasing the Murideo Field Test Monitor
•18Gbps 4K60 with HDR Support
•7 Inch Full HD Playback Screen
•Built-in Signal Analyzer
•HDCP 2.3 Support
•Battery Adapter for on-the-go testing
•EDID Management
Murideo's Test Monitor is a single, seven-inch monitor built for testing 4K signals up to
18Gbps. This compact device comes with a battery adapter for working around a job
site, but also fits perfectly at the rack with its HDMI loop out port that will pass along
any 4K signal.
As a part of the Murideo testing and troubleshooting family, you know the standards
are the highest in the industry. This monitor offers signal analyzer information such as
resolution, color space, HDCP, HDR confidence, and audio type analysis.
Mount it locally in a rack or use the battery pack to take it with you, no matter how you
use it, hunting down HDMI issues just got a lot easier with Murideo's HDMI 4K Test
Monitor.
What's in the Box
•x1 Field Test Monitor
•x1 12V DC/AC Power Supply
•x1 HDMI Cable
•x1 Adjustable stand
•x1 Battery Adapter
o(fits 7.2V Sony NP-F series batteries)
•x2 sets of mounting screws
oOne set for stand, one for Battery Adapter
MUR-MON-SING
Page 4

MUR-MON-SING
Page 5

Device Overview: Top Buttons
From Left to Right Buttons
•< MENU >
oClick-able scroll wheel for navigating the Menu
oWhen not in the Menu, this wheel can adjust the Monitors brightness, contrast,
saturation, tint, sharpness, and Volume (see page 10 for details)
•EXIT
oExit or back button for navigating the Menu
•F1
oProgrammable button
oDefault is Aspect Ratio (button press changes aspect ratio)
•F2
oProgrammable button
oDefault is Audio Level Meter (button press turns On/Off)
•F3
oTurns on screen signal info On/Off
MUR-MON-SING
Page 6

Menu: Picture
•Brightness - Adjust the Field Test Monitors screen brightness
o0~100 (Default +50)
•Contrast - Adjust the Field Test Monitors screen contrast
o0~100 (Default +50)
•Saturation - Adjust the Field Test Monitors screen saturation
o0~100 (Default +50)
•Sharpness - Adjust the Field Test Monitors screen sharpness
o0~100 (Default 0)
•Color Temp. - Adjust the Field Test Monitors screen color temperature
o6500K, 7500K, 9300K, and USER (see note below)
*NOTE: When in USER Color Temp, you have the ability to alter RED/GREEN/BLUE Gain and Offset
Gain is adjustable from 0~255, default is +128 for all three colors (red/green/blue)
Offset is adjustable from 0~511, default for is +256 for all three colors (red/green/blue)
MUR-MON-SING
Page 7

Menu: Function
•Scan - To change the Aspect ration this needs to be set to Aspect. To change the Display
Scan settings, change to Scan. Pixel to Pixel does not alter the image (this will also lock out
other settings)
oAspect, Pixel to Pixel, Zoom
•Aspect - Changes the displays aspect ratio (Scan field must be set to Aspect)
oFull, 16:9, 1.85:1, 2.35:1, 4:3, and 3:2
•Display Scan - (Scan field must be set to Aspect or Zoom)
oFull-scan (full picture), Over-scan (zooms in), and Under-scan (zooms out)
•Check Field - Color decoding check
oOff, Mono, Red, Green, and Blue
•Zoom - Changes the Zoom level (Scan field must be set to Zoom)
ox1.5, x2, x3, and x4
•Freeze - Turning On, freezes the current image on the screen
oTo un-freeze, turn Freeze option Off
•Image Flip - This rotates/flips the screen allowing for multiple configurations
oH (flips image Horizontally)
oV (flips image Vertically)
oHV (flips image both Horizontally and Vertically)
MUR-MON-SING
Page 8

Menu: Audio
•Volume - Changes the built in speakers volume level
o0~100 (Default is 50)
•The volume can also be adjusted without going into the menu (see page 11)
•Level Meter - Turns the on screen Level Meter On/Off
•This can also be turned On/Off by clicking the F2 button (with default settings)
MUR-MON-SING
Page 9

Menu: System
•Language - Changes the monitors language
•OSD Timer - Changes how long the OSD (On Screen Display) is visible
o10, 20, and 30 seconds
•Back Light - Changes the monitors back light level
o0~100 (Default is 100)
•F1 Config - Changes the F1 button functionality
oAspect, Freeze, Image Flip, Level Meter, Check Field, Display Scan, and Scan
•F2 Config - Changes the F2 button functionality
oAspect, Freeze, Image Flip, Level Meter, Check Field, Display Scan, and Scan
•EDID - Change the built in EDID
•EDID Enable - To set the selected EDID
oUnder EDID, select the desired EDID then select EDID Enable and turn On.
Default is 1920x1080P 2Ch.
•Reset - Resets the Field Monitor to its default settings (scroll past EDID Enable)
MUR-MON-SING
Page 10