Murphy PowerView PV750 User manual
00-02-0686
08-20-10
Section 78
PowerView™
Model PV750
Installation and Operations Manual
In order to consistently bring you the highest quality, full featured products, we reserve the right to change our
specifications and designs at any time. The latest version of this manual can be found at www.fwmurphy.com.
Please read the following information before installing.
BEFORE BEGINNING INSTALLATION OF THIS MURPHY
PRODUCT:
Read and follow all installation instructions.
Please contact FW MURPHY immediately if you have any
questions.
Table of Contents
Table of Contents....................................................................................................................iii
Hardware Installation.............................................................................................................. 1
Inspecting Package Contents.......................................................................................1
Dash-Mounted Installation............................................................................................1
Wiring Instructions ................................................................................................................. 5
Single Engine...............................................................................................................5
PVA and Dual Engine Gages.......................................................................................6
USB Wiring...................................................................................................................7
Analog Video................................................................................................................8
NMEA Wiring................................................................................................................9
Pin Specifications for Deutsch DT04-6P Style Connections.......................................10
Wiring Schematic.......................................................................................................11
PV750 Features and Operations.......................................................................................... 12
Setting Up your PV750 Display for the First Time............................................................. 13
Product Features................................................................................................................... 15
Power Up ...................................................................................................................15
Main Menu .................................................................................................................15
Gauge Display............................................................................................................16
Engine Diagnostics ....................................................................................................19
Fault Code Popups ....................................................................................................21
User Settings..............................................................................................................22
Utilities .......................................................................................................................27
Specifications........................................................................................................................ 29
Section 78 00-02-0686
08-20-10 - 1 -
Hardware Installation
The following instructions will guide you through installing the PowerView display.
Inspecting Package Contents
Before attempting to install the product, it is recommended that you ensure all parts are
accounted for and inspect each item for damage (which sometimes occurs during shipping).
The items included in the box are:
PV750 unit
Installation kit – P/N 78-00-0638 includes:
•4 ea. machine screws and flat washers
•4 Nylock nuts
•Installation & Operations manual – P/N 00-02-0686
Dash-Mounted Installation
Tools needed.
•Drill with 5/32” size bit
•Jig Saw
•Wrench or socket 6-32 Nylock nuts (provided) to studs
Preparing the Dash
Determine the location of the PowerView in the dash. Use the Installation Template (included
at the end of the manual) as a guideline to cut a hole in the dash to the specified dimensions.
Drill holes where indicated on the template for the mounting screws.
NOTE: When using the paper template from the manual, if you downloaded this
document from the FW Murphy website, be aware that the pdf file may not
automatically print to scale. When submitting the file for print, you will need to
select “None” for Page Scaling. Check the accuracy of the printed template by
verifying the measurements labeled on the template are correct.
If this manual was supplied with your product, the template will be correct.
Section 78 00-02-0686
08-20-10 - 2 -
Mounting the Unit
1. Place the back side of the display through the opening in the dash.
2. Use the four screws to line up the unit with the drilled holes.
3. Push the unit through the opening and screws through the drilled holes until the back of
the case is flush.
4. Use the Nylock nuts provided to tighten unit to the dash. Use the appropriate wrench or
socket to tighten. Torque lock nuts to 8-10 inch pounds.
Flush Mounting the Dash
1. Cut the dash to allow for the display without bezel. Ensure x amount of materials is
available to ensure the display is properly secured within the dash. Torque the 6-32
Nylock nuts to 5 inch pounds.
2. Place the display behind dash and line up the four mounting holes on the display with
the holes in dash.
3. Install four bolts and tighten nuts.
Section 78 00-02-0686
08-20-10 - 5 -
Wiring Instructions
The following illustrations are examples of various typical quick-connect options for setup.
Wiring harnesses are sold separately.
Single Engine
Section 78 00-02-0686
08-20-10 - 6 -
PVA and Dual Engine Gages
NOTE: Port B and C connectors are keyed differently than Port A and D
connectors to ensure proper connection.
If both PVA gages and Video camera are going to be utilized, an extra harness is
needed. P/N 78000688 PVW-750-MINI
Section 78 00-02-0686
08-20-10 - 7 -
USB Wiring
Section 78 00-02-0686
08-20-10 - 8 -
Analog Video
NOTE: If both PVA gages and video camera are going to be utilized, an
extra harness is needed. P/N 78000688 PVW-750-MINI.
Section 78 00-02-0686
08-20-10 - 9 -
NMEA Wiring
Section 78 00-02-0686
08-20-10 - 10 -
Pin Specifications for Deutsch DT04-6P Style Connections
Signal Definitions
CAN: 3 ports according to CAN specification 2.; 1 port isolated according to NMEA 2000 USB
2.0 host Video input (optional): NTSC/PAL Inputs (3) 0-5 VDC analog inputs, (1) input
configurable to support measurement frequencies from 2 Hz - 10kHz values from 0-100% duty
cycle Output: Digital, capable of sinking 500mA.
Section 78 00-02-0686
08-20-10 - 11 -
Wiring Schematic
Section 78 00-02-0686
08-20-10 - 12 -
PV750 Features and Operations
Flat Screen Display
A color screen displays gauges, soft key commands, and fault messages, as well as menu
options for setup and configuration.
Soft Key Commands
Columns of vertical commands may be located to the left and/or right of the display. They will
change according to the options available for the screen being displayed.
Soft Keys
The soft keys correspond to the soft key commands and allow you to make selections
accordingly.
MENU Key
Pressing the MENU key at any time displays the list of menu options.
ENTER Key
Pressing the ENTER key will select the option displayed much like the ENTER key on a
keyboard. The ENTER key also brings up the soft keys. Press once to display the left and
right arrows. Press twice to display all the soft keys. Press three times to hide all the soft
keys.
Section 78 00-02-0686
08-20-10 - 13 -
Setting Up your PV750 Display for the First Time
The guidelines presented below are intended for setting up the PV750 display for the first time.
Once the configuration is set up, there is no need to revisit or change any of the settings.
NOTE: If you require assistance during the set up process, contact FW Murphy
customer support at (918) 317-4100.
1. At the main menu, press the soft key to the left of ‘Utilities’.
2. The Utilities sub-menu is displayed.
Section 78 00-02-0686
08-20-10 - 14 -
3. From the ‘Utilities’ sub-menu, select ‘System Settings’. The following screen is
displayed.
4. With the cursor highlighting the J1939 source addresses, use the left side soft keys to
scroll through the ports and the right side soft keys to change the address. Press the
Save key to save selected changes or the Restore Defaults key to return to the default
settings. The field options consist of the following:
Section 78 00-02-0686
08-20-10 - 15 -
Product Features
Power Up
The PowerView display is most frequently installed with power connected to the ignition.
When the ignition is turned on, the PowerView display powers up and the engine health
statistics can be viewed via preset gauges. To see more gauge screens, press the Enter key.
Main Menu
The main menu is activated at any time by pressing the Menu key on the display.
The following features are accessed through the main menu:
•Gauge Display – provides a series of screens that display engine and auxiliary
information in a variety of formats.
•Engine Diagnostics – displays a list of engine fault codes and descriptions.
•User Settings – allows you to customize the display options for ambient light and
brightness, set US or metric units, language, specify the Home screen and screen setup
status.
•Utilities – allows configuration of the plug address. Also displays software version
information at the top of the page.
Section 78 00-02-0686
08-20-10 - 16 -
Gauge Display
The Gauge Display screen consists of several predefined layouts that contain combinations of
analog gauges, straight bar gauges, or digital (text) readouts. These screens are displayed
upon startup.
To scroll through the various gauge screens, press the Prev and Next soft keys. This can be
repeated until all screens have been viewed. The currently displayed screen will stay active
until another key is pressed.
Soft Key Commands
When a Gauge Display screen is active, pressing the Enter key will display soft key
commands, as shown below. Continuing to press Enter will toggle through any additional soft
keys, and will eventually remove the soft key commands from the screen.
Soft Key commands provide quick navigation and access to the following features:
•Video
•Day/Night
•Home
•Prev
•Next
Section 78 00-02-0686
08-20-10 - 17 -
Home - This one-touch navigation feature allows a pre-defined Home screen to be accessed
from the available Gauge Display screens. Once selected, the Home screen will be displayed
anytime the Home key is pressed.
NOTE: For instructions on how to setup the Home screen, refer to the “User
Settings” section of this manual.
Day/Night - Allows you to toggle the display screen between Day View and Night View.
NOTE: This feature can also be changed in the “User Settings” section of this
manual.
Day View Night View
Video – When enabled, displays either full screen video or partial video within a window on the
gauge display.
NOTE: For instructions on how to enable full or partial screen video, refer to the
“User Settings” section of this manual.
Full Screen Video
Example Partial Screen Video
(Video Screen displayed is from custom configuration)
Section 78 00-02-0686
08-20-10 - 18 -
.Previous and Next keys allow you to scroll through and display the various gauge
screens.
NOTE: For instructions on how to turn screens ON or OFF, refer to the “User
Settings” section of this manual.
Table of contents
Other Murphy Monitor manuals
Murphy
Murphy PowerView PV780 User manual
Murphy
Murphy PowerView PV1000 User manual
Murphy
Murphy HelmView GPS Kit Owner's manual
Murphy
Murphy powerview pv350 r2 User manual
Murphy
Murphy PowerView PV-101-Cs User manual
Murphy
Murphy PowerView PV101-A-HAZ User manual
Murphy
Murphy PowerView PV-101 User manual
Murphy
Murphy HelmView GPS Kit User manual
Murphy
Murphy PowerView PV1200 User manual
Murphy
Murphy PowerView PV1000 User manual
Murphy
Murphy PowerView PV780B User manual
Murphy
Murphy HelmView HV1000 User manual
Murphy
Murphy HelmView HV1000 User manual
Murphy
Murphy HelmView HV450 User manual
Murphy
Murphy PowerView PV780 User manual
Murphy
Murphy PowerView PV350 User manual
Murphy
Murphy PowerView PV-101-A User manual
Murphy
Murphy EMS447 User manual
