Muscle Rack UR361860PB4P-SV User manual

MODEL:
UR361860PB4P-SV
(D) Wood Shelf
(A) Post
(B) Brace
4-SHELF Boltless Steel Shelving
with parcleboard shelves
36W x 18D x 60H”
Should you have any comments, damage, missing parts, or problems with assembly of this unit contact us:
Chat: www.edsal.com/chat or www.edsal.com/contact
Email: [e-mail]
Phone: [phone]
To obtain replacement parts please provide: Model Number, Part Number & Description,
Location Purchased, and Date Purchased
Edsal Manufacturing Co. LLC
Chicago, IL 60609
US Patents & Patents Pending
Rev: C063020
(C) Beam
(E) Post Joint
PARTS LIST
Descripon Qty Part Number
(A) Post 8URPS30-SV
(B) Brace 8URBR18-SV
(C) Beam 8URBM36-SV
(D) Wood Shelf 4RPB31836
(E) Post Joint 4MPC0409-SV
(F) Post Cap 8RL-PC-B1.4
IMPORTANT SAFETY INFORMATION
Read through this enre manual for important guidelines and instrucons prior to assembly. Failure to follow these guidelines and
instrucons can result in property damage or serious personal injuries.
This unit should be placed on a level surface. Failure to do so can result in poor product performance or create a possible safety haz-
ard. DO NOT CLIMB, STAND or USE THIS UNIT AS A LADDER. TO PREVENT TIPPING, ALWAYS SECURE TO A WALL WITH SUITABLE FAS-
TENERS, NOT INCLUDED. DO NOT USE THIS UNIT TO STORE AQUARIUMS. CAUTION: CONTAINS SMALL PARTS, KEEP CHILDREN AWAY
DURING INSTALLATION. USE TWO OR MORE PEOPLE TO ASSEMBLE AND MOVE THE UNIT TO AVOID INJURY. Do not use this unit for
anything other than the manufacturer’s intended purpose. Use care when working with metal parts, wear gloves for protecon. Pe-
riodically inspect the unit to ensure brace/beam rivets are properly seated into post slots. Keep this manual for future reference.
Do not exceed the maximum weight capacity of 800 lbs (363 kg) for each shelf, not to exceed 4,000 lbs (1,814 kg) for the enre
shelving unit. Evenly distribute weight loads across enre shelf surface. Always store larger, heavier items on the boom levels and
small lighter items on the upper levels.
Assembly is done with the rivets of the beams and braces ng into the slots of the post. A rubber mallet may be used on the
beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block of wood between
the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and fully engaged.
GENERAL INSTRUCTIONS
PARTS
(F) Post Cap

Begin by placing four (4) post caps to the boom of four (4) posts
(see gure A). Next, assemble two (2) post with one (1) brace.
Skipping one slot from the boom of the post (see gure B),
place the rivets into post with the narrow end of the slots
poinng down, and with the shelf ledge of the brace facing up
(see gure C). Tap lightly on the top edge of the brace to seat
rivets. Repeat with two (2) post and one (1) brace. Next assemble
the two (2) post units with two (2) beams, skipping one slot from
the boom of the post (see gure D). Place the rivets into post
with the narrow end of the slots poinng down, and with the
shelf ledge of the brace facing up (see gure C). Tap lightly on the
top edge of the beam to seat rivets.
Step
1
Add a wood shelf to the level previously built (see gure E),
then connue working by adding the second level using two (2)
beams and two (2) braces in the post slots of your desired
locaon (see gure F). Again, place the rivets of the beams and
braces into the post slots with the shelf ledge facing up and tap
lightly to seat the rivets. Add a wood shelf to the
second level.
Figure D
Beams
Brace
Posts
Figure B Wood Shelf
Beams
Braces
Wood Shelf
Figure F
Step
2
Figure E
Figure A
Post
Post cap
Posts are
direconal.
The narrow
end of the
slots must
point down.
Brace/Beam
Rivets
Figure C
Tap down
lightly to seat
the rivets
Add a wood shelf to the previously built level, then connue by
adding the fourth level to the unit using two (2) beams and two (2)
braces per level. Tap lightly to properly seat the rivets and add the
nal wood shelves to the unit (see gure H). Finally place the four
(4) post caps on the top of each post (see gure I).
Double check to make sure all rivets are fully engaged into the
narrow end of the post slots. Assembly is now complete.
Note: Post are direconal.
The narrow end of the slots
must point down.
Figure G
Figure H Figure I
Step
3
Step
4
ASSEMBLY INSTRUCTIONS
Fourth
Level
Top
Post
Inside
View
Bottom
Post
Post
Joint
Outside
View
Wood
Shelf
Assemble four (4) posts to the four boom post assemblies by
using four (4) of the post joints. Place the post joint into the top
of the boom post assembly and tap down to properly seat. Next
place a post into the top of the post joint and tap down to
properly seat (see gure G). Connue by adding the third level
using two (2) beams and two (2) braces just above the post joints.
Again tap lightly to seat the rivets.