Mustang MV-ARM-S User manual

TOOLS REQUIRED:
Hardware
Power Drill
5/32" or 1/3" Drill Bit
Phillips Head Screw Driver
Spirit Level
Component Checklist
Important Notes
Wall Arm Assembly(x1)
Mounting the Wall Plate
Timber Stud Wall
•
•
•
•
Adapter Panel(x1)
5/32” holes
WARNING
wo
od
s
t
u
d
w
a
l
l
A
1
M4x10mm Phillips
Head Screw(x4)
M4x20mm Phillips
Head Screw(x4)
M5x16mm Phillips
Head Screw(x4)
Spacer(x4)
Alligator anchor(x3)
M6x20mm Phillips
Head Screw(x4)
M6x30mm Phillips
Head Screw(x4)
Allen Key (x1)
Flange Bolt (x3)
Flange Bolt (x3)
M5x20mm Phillips
Head Screw(x4)
M6x12mm Phillips
Head Screw(x4)
M8x12mm Hex
Head Screw(x4)
washer
(x4)
•
Installation will require a minimum of two people. Under no circumstances should this be
attempted by one person.
•We highly recommend this product be installed by a qualified professional person.
Please do not begin installation until you have thoroughly read and understood these instructions.
•
The Articulating Wall Mount supports display mounting from 26” to 40”, VESA 100/200 x 100/200 depending
on the TV mounting plate attached (provided separately) and supports a maximum of 80 lbs. (36kg).
Ensure the wall you plan to use will safely support 4 times the combined weight of the Articulating
Wall Mount and your chosen display.
Under no circumstances should this product be mounted to metal studs.
The manufacturer does not accept responsibility for incorrect installation.
• Tighten screws so that wall plate is firmly attached
but do not over tighten. Over tightening can damage
the screws, greatly reducing their holding power.
• Never tighten in excess of 80” / lb. (9N.M.)
• Make sure that mouting screws are anchored into
the center of the studs. The use of an “edge to edge”
stud finder is highly recommended.
MV-ARM-S INSTALLATION INSTRUCTIONS
Country of origin: China Contact number: 866-395-0370 Warranty: 5 years
Use the wall plate as the template, then mark the wall plate holes onto the wall.

Drill three 1/3” holes
Anchor
Wall arm assembly
slots
Attaching Adapter Panel to Screen
B
2
•When installing wall arm assembly on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness
in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block,
generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that
a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of
the hole when entering a void or cavity.
•Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
•Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
WARNING
concrete
wall
Drill holes and
insert anchors.
Place
wall
arm assembly
plate over anchor
and secure with
screw.
Tighten all
fasteners.
WALL ARM
WALL
ARM
wood screw
WEIVYAWATUC
CORRECT
concrete
plaster/
dry wall
INCORRECT
concrete
plaster/
dry wall
WALL
ARM
Installation to Solid Concrete and Cinder Block
Note: Ensure the Wall Arm Assembly
is mounted with the slots pointing upwards.
Flange screw
M4&M5&M6
MountingScrew
Adapter Panel
Adapter Panel
For VESA 75x75, 100x100 or 200x200
NO TE: For VESA 75x75,100x100,100x200,200x200,the Adapter
Panel is needed only,attach Adapter Panel to screen using
M4 & M5 & M6 mounting screw.
When installing displays
with recessed / pocket hole
patterns, spacers should be
used between the screen
adapter plate and the flat panel.

Cable Management
D
NOTE: Be sure to leave enough slack
to allow for movement of the arms.
3
Note: For demonstration purposes, the wall has been omitted from the image.
E Optional
If more or less tension is desired in the arm pivot points,
do the following:
• To increase tension, turn Screw Bolts clockwise with M8mm
Allen Key.
• To reduce tension, turn Screw Bolts counter-clockwise with
M8mm Allen Key. Do not turn more than half a turn.
Screw Bolts
Installing display
C
Insert two M8x12mm (O) screws and two
8mm metal washers (S) into top two holes
of Adapter Plate. Leave approximately 1/4”
of exposed thread (Do NOT tighten fully).
Lift the display and hook it over the
mounting head by lowering the exposed
portion of the top screws into the open key
slots of Wall Arm Assembly mounting head.
Once in position, attach the bottom two
M8x12mm screws (O) and 8mm metal
washers (S) to secure the Adapter Plate
to the mounting head using the Allen
Key (T) to tighten down all M8 screws
(See Figure 10).
M8x12mm
Screw
Top Screw
8mm Metal
Washer
INSTALLATION COMPLETE