Mustang MV-PROJSP-FLAT User manual

Installation Guide MUSANG
Universal
Projector
Low Profile
Mount
MV-PROJSP-FLAT

Important Notes Parts Specifications
Thank you for purchasing the Universal Projector Flush Mount. This
bracket is suitable for about 80% to 90% of projectors up to15kg
(33Ibs).
To ensure correct usage, please read this instruction manual
thoroughly. Keep this manual for future reference.
Bracket should be mounted only by qualified installer.
User willbe responsible for any injuries and damages that may arise
from improper installation and handling of Universal Ceiling
Mounting Kit.
Ensure all mounting screws are appropriately positioned and
properly tightened/fastened.
Installers are to ensure customer's safety during installation.
We reserve the right to amend or undertake any necessary changes
without prior notice.
/\ WARNING
This symbol indicates the incorrect handling. Ignoring this symbol
can result in the possibility of personal injury or even death.
AN CAUTION
This symbol indicates the incorrect handling. Ignoring this symbol
can result in the possibility of personal injury and physical damage.
A This symbol indicates additional cautions (including warnings).
O This symbol indicates forbidden actions.
Q) This symbol indicates required actions.
A Q O
Caution Forbidden Required
(general) (general) (general)

Z\WARNING Z\CAUTION
Assembling without the use of bolts and screws
at designated points may result in injury and
damage to properties or the unit collapsing -
from its installed position. v Do not install at place where there are excessive
When a malfunction occur, disconnect the — dust and smoke as fire could arise from these
power from the main socket and surround the :
area with ropes to prevent others from getting
near it.
Do not install near an air-conditioner.
sources.
Check and ensure the ceiling where you install
can support the load of the unit and Ceiling
Mounting.
Steps should be taken to ensure the ceiling and Keep the room well ventilated to prevent room
installed unit can withstand external forces like 5 temperature rising and possibilities resulting in 100mm (3.94*) or moro È
earthquakes, vibrations, etc. z fire. 100mm {3.94~) or more
All Ceiling Mounting Brackets are to be firmly Do not install in location where room temperature
secured so the unit will not drop off its installed Allen Key a and humidity are excessively high to prevent fire.
position. ao 3
To prevent the fire, avoid contacting with water.
Do not remove any bolts and screws from the Ceiling Do not apply unnecessary stress or load on the
Mounting Brackets or do any changes to the Ceiling = — installed unit.
Mounting Brackets.

Package Contents Package Contents
Each package should contain the parts listed as shown below.
Part 11 Part 12
Washer M8 Spring Washer
Part 1 À Part 2
Ceiling Plate U-Brocket Part 13 Part 14
Bottom Spacer Square Nut
Part 3
Extension Brocket
Part 16
General Base Plate
Part 15 M6x12 Carriage Bolt
M5x10 Socket Button Cap Screw
Part 5
Cross Adapter Part 18
\ a
M6 Serrate Flange Nut
Truss Head Screw
M4x15 / M4x20 / M4x25 4 pcs each
Part 7 M5x15 / M5x20 / M5x25 4 pcs each
Locking Hook M6x15 / M6x20 / M6x25 4 pcs each
Part 9
Socket Cap Screw
Part 10
M8 Self-Locking Nylon Nut

Installation Guide
1. Parts Assembly - Installation of Universal Base
1.1
Lift the Projector with both middle finger along
the depth of the Projector to search for the Central
Gravity (CG).
1.3
When the CG Point ( Depth of Projector ) and
( Width of projector ) intersection meet , that will
be the assume CG of Projector.
CG of Projector CG of Point
(Width of Projector)
Select the suitable Extension Bracket from the
Package. There are 4 sizes available as shown.
1.2
Lift the Projector with both middle finger along
the depth of the Projector to search for the Central
Gravity (CG ). Ù h
1.4
Locate the Projector CG Position and determine
screw size for mounting the Projector. Place the
Universal Base Plate near to the Projector CG
and select the suitable Extension Bracket given
in the package.
Thread
1.6
Select the suitable Extension Bracket and place
it on the Projector near the CG position follow
by the Universal Base Plate. Make sure the
Extension Bracket is able to assemble to the
Universal Base Plate.
Installation Guide
1.7
Assemble the selected Extension Bracket with
the following items: Bottom Spacer, Spacer
( if needed ) & Square Nut.
*For Extension Bracket more than 50mm (1.97)
( Square Nut X 2 )
Bottom Spacer
Spacer of
Various Size
=
ST
Oo si Bottom Spacer
Bottom Spacor Spacer of
Various Sizo
1.9a
Assemble the Universal Base Plate with the
required items as shown in the picture.
M6 Nut (Qty:2pcs)
& 2
4) A
Gi U- Joint Bracket (Qty: Ipc)
Universal Base Plate (Qty: Ipc)
A A M6 Carriage bolt (Qty:2pcs)
1.10
Align the assembled Universal Base Plate with
all the Extension Bracket as shown in the picture.
Using M5 Button Socket Cap Screws to hand
tighten it.
1.8
Assemble the respective Extension Bracket to the
Projector as shown in the picture. Using respective
Truss Head Screw from the given package to
tighten lightly.
Full assembled of the Universal Base Plate as
shown in the picture.
*Do not tighten the M6 Nut until the CG is
finalized.
1.11
Attach the Assemble Parts as in step 1.6 to the
Universal Base Plate as shown. Lift up the
Projector to check the CG of the assembly
before force tightening the M5 Button Socket
Cap Screws and the Mé Nut. The assembly is
then completed.

Installation Guide
1.12
For easy and quick installation
the universal base has been pre-installed.
2. Installation of Universal Ceiling Mounting Kit
2.1 | 2.2
Install the Ceiling plate to the ceiling by M10 bolt Install Shoft
(not included) into the ceiling. Connect the shoft with the Bottom Column,
Rsferia dicon insert the Locking Hook into the cutting slot.
gram. Tighten them with M8x50 Socket Cap Screw
and M8 Self-Locking Nylon Nut.
Refer to drawing.
2.3
Installation completed.
*Please consult our authorized service person when you meet any trouble in installation. We are
not liable for any damage or injury caused by mishandling or improper operation.
10