Mustang MV-ARM-XS1 User manual

TOOLS REQUIRED:
Hardware
Power Drill • 0.25" (6mm) Drill Bit
0.4” (10mm) Masonry Drill Bit
Phillips Head Screw Driver
0.5” (13mm) Socket Wrench or Shifter
Component Checklist
Important Notes
Wall Arm Assembly(x1)
•
•
•
•
A
1
•
Installation will require a minimum of two people. Under no circumstances should this be
attempted by one person.
• We highly recommend this product be installed by a qualified professional person.
Please do not begin installation until you have thoroughly read and understood these instructions.
•
The Articulating Wall Mount supports display mounting from 10” to 32”, VESA 75 x 75mm, 100 x 100mm,
and 200 x 200mm, and a maximum of 55 lbs. (25kg).
Ensure the wall you plan to use will safely support 4 times the combined weight of the Articulating
Wall Mount and your chosen display.
Under no circumstances should this product be mounted to metal studs.
The manufacturer does not accept responsibility for incorrect installation.
MV-ARM-XS1 INSTALLATION INSTRUCTIONS
Country of origin: China Contact number: 866-395-0370 Warranty: 5 years
VESA Plate
Timber Stud Wall
Masonry Wall
Remove the the mount from
the packaging and open fully.
- Drill two 6mm (0.25”) diameter
holes, 50mm (2”) deep.
- Secure the Mounting Plate to the
wall using the Coach Bolts supplied.
Coach Bolt (x2)
Concrete Anchor (x2)
M4/5 Spacer (x4)
Security Screw (x1)
3mm Allen Key
M4x16/25mm (x4 each)
M5x16/25mm (x4 each)
M6x16/30mm (x4 each)
Display Mounting
Screws
M4/M5 Washers
(x4 each)
M6/8 Spacer (x4)
Attaching Arm to the Wall
OR
- Drill two 10mm (0.4”) diameter
holes, 50mm (2”) deep.
- Secure the Mounting Plate to the
wall using the Coach Bolts and
Concrete Anchors supplied.
Use the wall plate as the template, then mark the wall plate holes onto the wall.

Back of Display
Mounting Screws (x4)
Washers (x4)
VESA Plate
Choose appropriate Mounting Screws and
Washers from the Hardware supplied
to suit your Display.
Washer
Mounting Screw
Recessed Mounting
Holes or Display with a
Curved Rear Panel
If the Mounting Holes are
recessed into the back of the
Display, or the Display has a
curved rear panel, use the
appropriated Spacer Bushes
supplied to pack the
Mounting Holes.
Note: Ensure the VESA
plate is securely fixed
to the display.
Display
Top of
Mounting Hole
Spacer
TIGHTEN
Security Screw
Insert the Security Screw, and tighten using the
Phillips-head Screwdriver
Phillips-head Screwdriver
HOOK
VESA Ball Mount
Hook the top of the VESA Plate
onto the VESA Ball Mount.
VESA Plate
Press and hold the Release Buttons.
Gently push the bottom of VESA Ball Mount.
Release buttons to lock in place.
PUSH
Release Button
LOOSEN (-kg)
TIGHTEN (+kg)
3mm Allen Key
Tension Plate
Position your Display to the desired viewing angle using the 40º
angular movement allowed by the VESA Ball Mount.
If the display does not hold its position, or is too
resistant, adjust the Tension Plate located at the
rear of the VESA Ball Mount.
To make any adjustments, use the 3mm Allen Key
supplied. Apply half a turn at a time to each screw
on the Tension Plate to adjust evenly.
Check the display, and then adjust again if necessary.
+/- 20°
angular tilt
Rotate the Display as desired, locking the
Display into position by tightening the
Tension Plate.
360° infinite
horizontal rotation
TIP: Leave enough slack in the cables
to allow full movement at the joints.
Connect cables to your Display, and route along the arms.
Re-attach the Cable Covers to hold the Cables in place.
Cable Cover
Attaching Your Display to the Arm
C
Final Adjustment
E
INSTALLATION COMPLETE
Attaching the VESA Plate to Your Display
B
2
Cable Management
D
Remove the Cable Covers as required using a
Phillips-head Screwdriver.