MVMT EBT-4-21175 User manual

This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
FCC Disclaimer:
This device Complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1– This device may not cause harmful interference, and
2– This device must accept any interference received,
including Interference that may cause undesired
operation. The manufacturer is not responsible for any
radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could
void the user authority to operate the equipment.
1– This device may not cause harmful interference, and
2– This device must accept any interference received, including
interference that may cause undesired operation. The
manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. Such modifications could void the user's
authority to operate the equipment. Under Industry Canada
regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for
This device complies with Part 15 of the FCC Rules and Industry
Canada license-exempt RS5 standard(s). Operation is subject to the
following two conditions;
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or on experienced radio/TV technician
for help or assistance.
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for
successful communication.
Electronic and electrical devices disposal
This symbol indicates that electrical and electronic device is to be
collected separately.
This product is designated for separate collection at an
appropriate collection point. Do not dispose of as
household waste.
If the device use batteries, they must be removed from the
device and disposed in a appropriate collection center.
If the batteries cannot be removed, do not attempt to do it
yourself since it must be done by a qualified professional.
Separate collection and recycling helps conserve natural
resources and prevent negative consequence for human health
and the environment that might result from incorrect disposal. Warning: To prevent possible hearing damage, do not listen at high volume levels for long periods.
PARAMETERS
Bluetooth version: 5.0
Frequency: 2402- 2480MHz
Battery capacity: 30mAh each
Total playtime*: 3– 4 hours
Total standby time: 50 hours
Bluetooth range: Up to 30 ft
C H A R G I N G C A S E
Battery capacity: 300mAh
Charging time: 2 hours
Type-C USB charging
*Depen ds o n in dividual use
W I T H C H A R G I N G C A S
T W S E A R B U D S
E
INSTRUCTION MANUAL: EBT-4-21175
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

FCC ID: 2A3ZO-E BT4 -21175
FUN C TIO N K EYS
1. E ARBUDS: Just place the earbuds into the
charging case. The earbuds will
automatically enter charging mode if the
cradle is charged or connected to the
power supply. The earbuds will display a red
LED light while they are charging, and
turn off when they are fully charged.
2. CASE: Use the cable provided to connect
the charging case to the power supply.
To activate the voice assistant (i.g., Siri), press
an d ho ld the either ear bud ’s contro l bu tto n fo r
2 seconds.
VO IC E A SSISTAN T
C H A R G IN G
BLUETO O TH C O N N EC T
1. Power the device on. The earbuds will pair
with one another automatically when they
are turned on.
2. Turn on your device’s Bluetooth from the
Bluetooth menu and select “MV-EB5579”.
3. When paired successfully the device will
make a tone to confirm the connection has
been made to your device.
use to ensure longest play time.
Note: The earbuds will reconnect automatically if your device has been paired previously.
Depending on your device’s type and configuration, manual reconnection may be
required each time. Note: If you hold control button for 3 seconds earbuds will power down.
Take the two earbuds out of the charging
case. They will automatically turn on . Once
the earbuds have powered up, you should
hear a sound indicating that they have
automatically connected with one another.
TU R N O N
1. PLAY/STOP MUSIC: When playing music,
quickly press either earbud ’s control button.
2. M USIC CONTROL: When playing music, triple
press either control button for next song / last
song, Double press either button to decrease
volume / increase volume.
3. ANSWERING CALL: When a call is received,
briefly press either earbud’s control button.
4. HANGING UP: During a phone call, briefly
press earbud ’s control button to end call.
5. D ECLINING CALL: When playing music, press
and hold control button for 1.5 seconds*.
WARNING: The artwork and design of this package are
protected by United States Copyright law and may not be
reproduced, distributed, displayed, published, or used for
any purpose without prior written permission. You may
not alter or remove any trademark or copyright notice
from this package. Because of continuous improvements,
images and product specifications on packaging may
©2022 Argento SC, All Rights Reser ve d.
Distributed by Arge nto SC , N ew Yo rk, N Y 1 001 8.
Designed in New York . Made in C hina.
MVMT and M VMT logo are registered tradema rks of
Argento SC . The Bluetooth® word ma rk and logos a re
registered trademarks owned by B luetooth SIG, In c. a nd
any use of such marks by A rgento SC is under license.
www.arg entosc.com
suppor t@argentosc .com
Long press the control button until LED turns
away from case for more than 5 mins.
TU R N O FF

FCC ID: 2A3ZO-E BT4 -21175
FUN C TIO N K EYS
1. E ARBUDS: J ust place the earbuds into the
charging case. The earbuds will
automatically enter charging mode if the
cradle is charged or connected to the
power supply. The earbuds will display a red
LED light while they are charging, and
turn off when they are fully charged .
2. CASE: Use the cable provided to connect
the charging case to the power supply.
To activate the voice assistant (i.g., Siri), press
an d hol d the either ear bu d’s c on tro l bu tto n for
2 seconds.
VO IC E A SSI STAN T
C H A R G IN G
BLU ETO OTH C ON N EC T
1. Power the device on . The earbuds will pair
with one another automatically when they
are turned on.
2. Turn on your device’s Bluetooth from the
Bluetooth menu and select “ MV- EB 5579 ”.
3. When paired successfully the device will
make a tone to confirm the connection has
been made to your device.
use to ensure longest play time.
Note: The earbuds will reconnect automatically if your device has been paired previously.
Depending on your device’s type and configuration, manual reconnection may be
required each time. Note: If you hold control button for 3 seconds earbuds will power down.
Take the two earbuds out of the charging
case. They will automatically turn on. Once
the earbuds have powered up, you should
hear a sound indicating that they have
automatically connec ted with one another.
TU R N O N
1. PLAY/STOP MUSIC: When playing music,
quickly press either earbud’s control but ton .
2. M USIC CONTROL: When playing music, triple
press either control button for next song / last
song, Double press either button to decrease
volume / increase volume.
3. ANSWERING CALL: When a call is received,
briefly press either earbud ’s control button.
4. HANGING U P: During a phone call, briefly
press earbud’s control button to end call.
5. DECLINING CALL: When playing music, press
and hold control but ton for 1.5 seconds*.
WARNING: The artwork and design of this package are
protected by United States Copyright law and may not be
reproduced, distributed, displayed, published, or used for
any purpose without prior written permission. You may
not alter or remove any trademark or copyright notice
from this package. Because of continuous improvements,
images and product specifications on packaging may
©2022 Arge nto SC , All Rights Rese rved.
Distributed by Argento SC , N ew Yo rk, NY 1001 8.
Designed in New York. M ade in China .
MVMT and M VMT logo are registered trademark s of
Argento SC . The B luetooth® word mar k a nd logos are
registered tradem arks owned by Blu eto oth SIG, I nc. a nd
any use of such marks by Arge nto S C is under license.
www.argentosc.com
suppor [e-mail]
Long press the control button until LED turns
away from case for more than 5 mins.
TU R N O FF

FCC ID: 2A3ZO-E BT4-21175
FUN C TIO N K EYS
1. E ARBUDS: Just place the earbuds into the
charging case. The earbuds will
automatically enter charging mode if the
cradle is charged or connected to the
power supply. The earbuds will display a red
LED light while they are charging, and
turn off when they are f ully charged.
2. CASE: Use the cable provided to connect
the charging case to the power supply.
To activate the voice assistant (i.g., Siri), press
an d h old th e either ea rb ud’s contro l but to n for
2 seconds.
VO IC E ASSISTA N T
C H A R G IN G
BLU ETO OTH C ON N EC T
1. Power the device on. The earbuds will pair
with one another automatically when they
are turned on.
2. Turn on your device’s Bluetooth from the
Bluetooth menu and select “MV-EB5579”.
3. When paired successfully the device will
make a tone to confirm the connection has
been made to your device.
use to ensure longest play time.
Note: The earbuds will reconnect automatically if your device has been paired previously.
Depending on your device’s type and configuration, manual reconnection may be
required each time. Note: If you hold control button for 3 seconds earbuds will power down.
Take the two earbuds out of the charging
case. They will automatically turn on. O nce
the earbuds have powered up, you should
hear a sound indicating that they have
automatically connected with one another.
TU R N O N
1. PLAY/STOP MUSIC: When playing music,
quickly press either earbud ’s control button.
2. M USIC CO NTROL: When playing music, triple
press either control button for next song / last
song, Double press either button to decrease
volume / increase volume.
3. ANSWERING CALL: When a call is received,
briefly press either earbud’s control button.
4. HANGING U P: During a phone call, briefly
press earbud ’s control button to end call.
5. DECLINING CALL: When playing music , press
and hold control button for 1.5 seconds*.
WARNING: The artwork and design of this package are
protected by United States Copyright law and may not be
reproduced, distributed, displayed, published, or used for
any purpose without prior written permission. You may
not alter or remove any trademark or copyright notice
from this package. Because of continuous improvements,
images and product specifications on packaging may
©2022 Arge nto SC, All R ights Reser ved.
Distributed by Argento SC , New York, NY 1001 8.
Designed in N ew York. Ma de in China .
MVMT and MVMT logo are registered trad emarks of
Argento SC . The B luetooth® word mark a nd logos are
registered tradema rks owned by Bluetooth SI G, I nc. an d
any use of such marks by Argento SC is un der license.
www.arge ntosc.com
suppor [e-mail]
Long press the control button until LED turns
away from case for more than 5 mins.
TU R N O FF

FCC ID: 2A3ZO-E BT4-21175
FUN C TIO N K EYS
1. E ARBUDS: Just place the earbuds into the
charging case. The earbuds will
automatically enter charging mode if the
cradle is charged or connected to the
power supply. The earbuds will display a red
LED light while they are charging, and
turn off when they are fully charged.
2. CASE: Use the cable provided to connect
the charging case to the power supply.
To activate the voice assistant (i.g., Siri), press
an d h old th e either ea rb ud’s contro l but to n for
2 seconds.
VO IC E ASSISTA N T
C H A R G IN G
BLU ETO OTH C ON N EC T
1. Power the device on. The earbuds will pair
with one another automatically when they
are turned on.
2. Turn on your device’s Bluetooth from the
Bluetooth menu and select “MV-EB5579”.
3. When paired successfully the device will
make a tone to confirm the connection has
been made to your device.
use to ensure longest play time.
Note: The earbuds will reconnect automatically if your device has been paired previously.
Depending on your device’s type and configuration, manual reconnection may be
required each time. Note: If you hold control button for 3 seconds earbuds will power down.
Take the two earbuds out of the charging
case. They will automatically turn on. O nce
the earbuds have powered up, you should
hear a sound indicating that they have
automatically connected with one another.
TU R N O N
1. PLAY/STOP MUSIC: When playing music,
quickly press either earbud ’s control button.
2. M USIC CO NTROL: When playing music, triple
press either control button for next song / last
song, Double press either button to decrease
volume / increase volume.
3. ANSWERING CALL: When a call is received,
briefly press either earbud’s control button.
4. HANGING U P: During a phone call, briefly
press earbud ’s control button to end call.
5. DECLINING CALL: When playing music , press
and hold control button for 1.5 seconds*.
WARNING: The artwork and design of this package are
protected by United States Copyright law and may not be
reproduced, distributed, displayed, published, or used for
any purpose without prior written permission. You may
not alter or remove any trademark or copyright notice
from this package. Because of continuous improvements,
images and product specifications on packaging may
©2022 Arge nto SC, All R ights Reser ved.
Distributed by Argento SC , New York, NY 1001 8.
Designed in N ew York. Ma de in China .
MVMT and MVMT logo are registered trad emarks of
Argento SC . The B luetooth® word mark a nd logos are
registered tradema rks owned by Bluetooth SI G, I nc. an d
any use of such marks by Argento SC is un der license.
www.arge ntosc.com
suppor [e-mail]
Long press the control button until LED turns
away from case for more than 5 mins.
TU R N O FF

This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
FCC Disclaimer:
This device Complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1– This device may not cause harmful interference, and
2– This device must accept any interference received,
including Interference that may cause undesired
operation. The manufacturer is not responsible for any
radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could
void the user authority to operate the equipment.
1– This device may not cause harmful interference, and
2– This device must accept any interference received, including
interference that may cause undesired operation. The
manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. Such modifications could void the user's
authority to operate the equipment. Under Industry Canada
regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for
This device complies with Part 15 of the FCC Rules and Industry
Canada license-exempt RS5 standard(s). Operation is subject to the
following two conditions;
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or on experienced radio/TV technician
for help or assistance.
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for
successful communication.
Electronic and electrical devices disposal
This symbol indicates that electrical and electronic device is to be
collected separately.
This product is designated for separate collection at an
appropriate collection point. Do not dispose of as
household waste.
If the device use batteries, they must be removed from the
device and disposed in a appropriate collection center.
If the batteries cannot be removed, do not attempt to do it
yourself since it must be done by a qualified professional.
Separate collection and recycling helps conserve natural
resources and prevent negative consequence for human health
and the environment that might result from incorrect disposal. Warning: To prevent possible hearing damage, do not listen at high volume levels for long periods.
PARAMETERS
Bluetooth version: 5.0
Frequency: 2402- 2480MHz
Battery capacity: 30mAh each
Total playtime*: 3– 4 hours
Total standby time: 50 hours
Bluetooth range: Up to 30 ft
C H A R G I N G C A S E
Battery capacity: 300mAh
Charging time: 2 hours
Type-C USB charging
*Depen ds o n in dividual use
W I T H C H A R G I N G C A S
T W S E A R B U D S
E
INSTRUCTION MANUAL: EBT-4-21175
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
FCC Disclaimer:
This device Complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1– This device may not cause harmful interference, and
2– This device must accept any interference received,
including Interference that may cause undesired
operation. The manufacturer is not responsible for any
radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could
void the user authority to operate the equipment.
1– This device may not cause harmful interference, and
2– This device must accept any interference received, including
interference that may cause undesired operation. The
manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. Such modifications could void the user's
authority to operate the equipment. Under Industry Canada
regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for
This device complies with Part 15 of the FCC Rules and Industry
Canada license-exempt RS5 standard(s). Operation is subject to the
following two conditions;
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or on experienced radio/TV technician
for help or assistance.
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for
successful communication.
Electronic and electrical devices disposal
This symbol indicates that electrical and electronic device is to be
collected separately.
This product is designated for separate collection at an
appropriate collection point. Do not dispose of as
household waste.
If the device use batteries, they must be removed from the
device and disposed in a appropriate collection center.
If the batteries cannot be removed, do not attempt to do it
yourself since it must be done by a qualified professional.
Separate collection and recycling helps conserve natural
resources and prevent negative consequence for human health
and the environment that might result from incorrect disposal. Warning: To prevent possible hearing damage, do not listen at high volume levels for long periods.
PARAMETERS
Bluetooth version: 5.0
Frequency: 2402- 2480MHz
Battery capacity: 30mAh each
Total playtime*: 3– 4 hours
Total standby time: 50 hours
Bluetooth range: Up to 30 ft
C H A R G I N G C A S E
Battery capacity: 300mAh
Charging time: 2 hours
Type-C USB charging
*Depen ds o n in dividual use
W I T H C H A R G I N G C A S
T W S E A R B U D S
E
INSTRUCTION MANUAL: EBT-4-21175
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
FCC Disclaimer:
This device Complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1– This device may not cause harmful interference, and
2– This device must accept any interference received,
including Interference that may cause undesired
operation. The manufacturer is not responsible for any
radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could
void the user authority to operate the equipment.
1– This device may not cause harmful interference, and
2– This device must accept any interference received, including
interference that may cause undesired operation. The
manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. Such modifications could void the user's
authority to operate the equipment. Under Industry Canada
regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for
This device complies with Part 15 of the FCC Rules and Industry
Canada license-exempt RS5 standard(s). Operation is subject to the
following two conditions;
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or on experienced radio/TV technician
for help or assistance.
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for
successful communication.
Electronic and electrical devices disposal
This symbol indicates that electrical and electronic device is to be
collected separately.
This product is designated for separate collection at an
appropriate collection point. Do not dispose of as
household waste.
If the device use batteries, they must be removed from the
device and disposed in a appropriate collection center.
If the batteries cannot be removed, do not attempt to do it
yourself since it must be done by a qualified professional.
Separate collection and recycling helps conserve natural
resources and prevent negative consequence for human health
and the environment that might result from incorrect disposal. Warning: To prevent possible hearing damage, do not listen at high volume levels for long periods.
PARAMETERS
Bluetooth version: 5.0
Frequency: 2402- 2480MHz
Battery capacity: 30mAh each
Total playtime*: 3– 4 hours
Total standby time: 50 hours
Bluetooth range: Up to 30 ft
C H A R G I N G C A S E
Battery capacity: 300mAh
Charging time: 2 hours
Type-C USB charging
*Depen ds o n individual use
W I T H C H A R G I N G C A S
T W S E A R B U D S
E
INSTRUCTION MANUAL: EBT-4-21175
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
FCC Disclaimer:
This device Complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1– This device may not cause harmful interference, and
2– This device must accept any interference received,
including Interference that may cause undesired
operation. The manufacturer is not responsible for any
radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could
void the user authority to operate the equipment.
1– This device may not cause harmful interference, and
2– This device must accept any interference received, including
interference that may cause undesired operation. The
manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. Such modifications could void the user's
authority to operate the equipment. Under Industry Canada
regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for
This device complies with Part 15 of the FCC Rules and Industry
Canada license-exempt RS5 standard(s). Operation is subject to the
following two conditions;
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or on experienced radio/TV technician
for help or assistance.
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for
successful communication.
Electronic and electrical devices disposal
This symbol indicates that electrical and electronic device is to be
collected separately.
This product is designated for separate collection at an
appropriate collection point. Do not dispose of as
household waste.
If the device use batteries, they must be removed from the
device and disposed in a appropriate collection center.
If the batteries cannot be removed, do not attempt to do it
yourself since it must be done by a qualified professional.
Separate collection and recycling helps conserve natural
resources and prevent negative consequence for human health
and the environment that might result from incorrect disposal. Warning: To prevent possible hearing damage, do not listen at high volume levels for long periods.
PARAMETERS
Bluetooth version: 5.0
Frequency: 2402- 2480MHz
Battery capacity: 30mAh each
Total playtime*: 3– 4 hours
Total standby time: 50 hours
Bluetooth range: Up to 30 ft
C H A R G I N G C A S E
Battery capacity: 300mAh
Charging time: 2 hours
Type-C USB charging
*Depen ds o n in dividual use
W I T H C H A R G I N G C A S
T W S E A R B U D S
E
INSTRUCTION MANUAL: EBT-4-21175
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

FCC ID: 2A3ZO-E BT4 -21175
FUN C TIO N K EYS
1. E AR BUDS: Just place the earbuds into the
charging case. The earbuds will
automatically enter charging mode if the
cradle is charged or connected to the
power supply. The earbuds will display a red
LED light while they are charging, and
turn off when they are f ully charged.
2. CASE: Use the cable provided to connect
the charging case to the power supply.
To activate the voice assistant (i.g., Siri), press
an d h old t he either e arb ud ’s contro l but to n f or
2 seconds.
VO IC E ASSISTAN T
C H A R G IN G
BLU ETO OTH C ON N EC T
1. Power the device on . The earbuds will pair
with one another automatically when they
are turned on.
2. Turn on your device’s Bluetooth from the
Bluetooth menu and selec t “MV-EB5579”.
3. When paired successfully the device will
make a tone to confirm the connection has
been made to your device.
use to ensure longest play time.
Note: The earbuds will reconnect automatically if your device has been paired previously.
Depending on your device’s type and configuration, manual reconnection may be
required each time. Note: If you hold control button for 3 seconds earbuds will power down.
Take the t wo earbuds out of the charging
case. They will automatically turn on. Once
the earbuds have powered up, you should
hear a sound indicating that they have
automatically connected with one another.
TU R N O N
1. PLAY/STOP M USIC: When playing music,
quickly press either earb ud ’s control button.
2. M USIC CONTROL: When playing music, triple
press either control button for next song / last
song, Double press either button to decrease
volume / increase volume.
3. ANSWERING CALL: When a call is received ,
briefly press either earbud ’s control button .
4. HANGING UP: D uring a phone call, briefly
press earbud’s control button to end call.
5. DECLIN ING CALL: When playing music, press
and hold control button for 1.5 seconds*.
WARNING: The artwork and design of this package are
protected by United States Copyright law and may not be
reproduced, distributed, displayed, published, or used for
any purpose without prior written permission. You may
not alter or remove any trademark or copyright notice
from this package. Because of continuous improvements,
images and product specifications on packaging may
©2022 Argento SC , All Rights Reserved.
Distributed by Arg ento SC , New York , NY 10 018 .
Designed in N ew York. Mad e i n China.
MVMT and MV MT logo are registered tradema rks of
Argento SC . The Bluetooth® word ma rk a nd logos are
registered trademark s own ed by B luetooth SIG, Inc. an d
any use of such marks by Argento SC is under lice nse.
www.argentosc .com
support@ argentosc.com
Long press the control button until LED turns
away from case for more than 5 mins .
TU R N O FF