MyBabiie MBBC2 User manual

Bedside Crib Instruction Manual
IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

Please read these instructions carefully before use and keep them for later reference.
Do not use this product without reading the instructions for use first.
This product complies with EN 1130:2019
WARNING: TO AVOID DANGER OF SUFFOCATION BEFORE USE, REMOVE AND DISPOSE OF ALL PLASTIC
BAGS AND PACKAGING MATERIALS AND KEEP THEM OUT OF REACH OF CHILDREN.
• Failure to follow these warnings and the instructions could result in serious injury or death. Always follow assembly
instructions for each product use mode.
• Read the instructions for use for the list of components. Periodically check the product for loose, damaged or
missing parts.
• This product is intended for use for babies aged between 0 and 6 months, weighing up to a maximum of 9 kg.
• Stop using the product as soon as the child can sit or kneel or pull itself up.
• DO NOT use crib if any parts are missing, damaged or broken.
• DO NOT substitute parts from other manufacturers.
• All opening, adjusting, anchoring and positioning operations of the product must be carried out exclusively by an
adult.
• The product is ready for use only when the locking mechanisms are engaged. Make sure they are securely fixed
before use.
• Be aware of the risk of fire and other sources of strong heat, such as electric bar fires, gas fires, e.t.c. in the near
vicinity of the crib.
• The product must always be used on a horizontal floor. Do not place the product onto a sloped surface with
your child inside.
• The product should be locked in the fixed position when a child is unsupervised in it.
• All assembly fittings should always be tightened properly and care should be taken that no screws are loose and
no open zippers or buttons, because a child could trap parts of their body or clothing (e.g. strings, necklaces,
ribbons, dummies, e.t.c.) which would pose a risk of strangulation.
Your child’s safety is your responsibility
If you have a problem with this product or require replacement parts, please visit www.mybabiie.com/support
Register your product at: www.mybabiie.com/warranties
Safety notes
2

WARNING:
• Do not place the product close to another product which could present a danger of suffocation or strangulation
(e.g. strings, blind/curtain cords e.t.c.)
• Young children should not be allowed to play unsupervised in the vicinity of a product.
• There must be no gaps between the product and the mattress of the parent’s bed. DO NOT use the product if
there are any gaps.
• Keep the fastening belts out of reach of children.
• Do not use more than one mattress in the product.
• Only use the mattress sold with this crib, do not add a second mattress on this one. Suffocation Hazards!
• Do not adjust or move the product when the child is inside.
• Do not use the product for more than one child at a time.
• Do not use the product without the frame.
• Do not position the crib near walls and obstacles to prevent trapping hazards.
• Placing additional items in the product may cause suffocation.
• Do not leave additional items (e.g. toys, pillows e.t.c.) inside the product that could reduce its depth.
• The maximum thickness of mattress used in the crib shall not be more than 50mm.
• The thickness of the mattress must be such that the vertical height (upper surface of the mattress until the upper
edge of the product’s sides) is at least 200mm. Do not use more than one mattress in the crib.
Warning:
Only use the mattress sold with the crib, do not add a second mattress on this one. Suffocation Hazards!
Your child’s safety is your responsibility
If you have a problem with this product or require replacement parts, please visit www.mybabiie.com/support
Register your product at: www.mybabiie.com/warranties
Safety notes
3

Parts list
Assembly instructions
1
B
B
C
A D
Take out base leg “B” and untie the fastening rope.
Support bar
MattressCrib body Pair of straps
Bottom support barSide frame stand
4

Assembly instructions
2
Press the spring button to
insert Support bar “A” into
Side frame stand “B”
3
4
Insert Support bar “A”
in to Side frame stand “C”
in the same way as
previous step.
The frame stand should
now look like this:
B
A
A
C
5

Assembly instructions
5
Attach the handrail joint to the top of either side of the frame stands.
6
Unzip the zipper of the bassinet’s cloth cover.
6

Assembly instructions
7
a. b.
c. d.
Press the spring pin down and clip the bassinet into the groove
8
Press down the spring buckle at the bottom of the bed and insert the
bottom support bar “D” into the connector on the bottom of the bed.
Cover the support bar with the cloth cover attached to the crib.
7
Press!
!
Caution pinch point.
Be careful when
joining parts.

Assembly instructions
9
Fix the velcro to complete the installation.
10
Place the mattress in the
crib with the padded side up.
8

Assembly instructions
11
The crib can be adjusted to 7 different height positions. In order to
adjust the height, press the button up or down and adjust the crib to the
desired position. Repeat this operation on the opposite side. The base
of the crib can be inclined slightly by adjusting the two legs to be
different heights.
WARNING: When using the crib attached top a bed the two legs of the
crib must be the same height (e.g. if the right leg is in position 12 then
the left leg must be in position 1 also.)
Position 1
Position 2
9

Parts list for co-sleeping mode
WARNING: DO NOT use this crib if any parts are missing, damaged or broken.
WARNING:
1. Only use the attachment system provided.
2. Keep the attachment system to the adults’ bed away from and out of the crib to
avoid the risk of strangulation.
3. Do not use the bedside sleep in an inclined position.
B
C
A D
Support bar
MattressCrib body Pair of straps
Bottom support barSide frame stand
10

After you have finished putting the product together you can convert it to
co-sleeping mode.
1
Open the crib
guardrail - First unzip
the bassinet, then
push the spring
buckle in the opposite
direction then lower
the tube.
2
Move the crib close to
the parents bed and
check the height of the
crib compared with the
mattress of the bed.
WARNING: A bedside
sleeper shall ONLY be used
once it has been securely
attached to the adult’s bed
or when the drop side is in
the fully raised position to
prevent the child falling from
height.
WARNING: To avoid hazards
from the child’s neck being
caught on the top rail on the side
that is next to the adult’s bed,
the top rail must not be higher
than the adult bed mattress.
Co-Sleeping mode instructions
11

Co-Sleeping mode instructions
3
Press the spring pin down and
pull the handles on both sides to
adjust the height of the crib. It
can be adjusted up and down.
4
Use the pair of straps provided to fix the crib to the parents bed.
Fix the crib and frame with the little buckle on the side of the crib,then
connect the strap with the big buckle. You should hear a click.
Same steps on the both sides.
WARNING: In co-sleeping mode the
2 legs of the crib should always be
adjusted to the same height.
Assembly steps of attachment straps
12

max 2 cm
Assembly steps of attachment straps
5
Four wheels with
locking function.
WARNING: Make sure
the four wheels are
locked before use.
WARNING: If there is any gap
between the bedside sleeper
and the adult bed, DO NOT use
this product.
WARNING: Do not fill any
spaces or gaps between the
parent’s mattress and the crib
with pillows, blankets,
bedsheets or any other material
that may cause the risk of
suffocation.
WARNING: Check the tightness
of the attachment system before
each use by pulling the bedside
crib in a direction away from the
adult bed.
Instructions for fixing to parent’s bed
6
To prevent a suffocation hazard from entrapment, the bedside sleeper
shall be properly secured to the adult bed using the attachment system.
13

Mattress, Boxsprings &
Frame aligned
Mattress, Boxsprings &
Frame not in-line
Instructions for fixing to parent’s bed
Suitable bed for
co-sleeping mode:
WARNING: The bedside crib is only available with beds between 52-69 cm tall
counting from the floor to the upper surface of the mattress.
A bedside crib is designed to provide a sleeping area for an infant until he/she
begins to push up on hands and knees or approximately 5 months of age.
Move your child to another sleeping option once this happens.
There is enough space between
the bottom of the bed and the
ground to allow the connected
straps to pass through.
There is no space between the
bottom of the bed and the ground,
the straps can not pass through.
Not suitable bed for
co-sleeping mode:
14

Care instructions
• Plastic and metal parts may be
sponged lightly using warm
water and a mild detergent.
• Dry thoroughly before storing.
• Never clean any part of the
product with abrasive, ammonia
based, bleach based or spirit
type cleaners.
WARNING: During the removal or
application of the lining, handle
the fabric carefully in order to
avoid accidental damage or tears.
Hand wash in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
15

/MyBabiie /MyBabiie@MyBabiie@MyBabiieOfficial
Follow us!
Register your product at:
This product qualies for 12 month warranty when
registered through our site
www.mybabiie.com/warranties
In the first instance of needing assistance please
contact your original place of purchase.
My Babiie. Part of My Companiie Ltd
Repton Manor, Repton Avenue, Ashford, Kent, TN23 3GP