mychway HR-T350 User manual

Page 1 , in 12 pages
—Please read the instructions before use！
Ⅰ.Brief Introduction
E-light applies three core technology, IPL, RF, and epidermis cooling. It combines the
USER MANUAL

Page 2 , in 12 pages
advantage of IPL and RF, in one hand, the skin absorbs IPL energy selectively, and the skin also
absorbs RF energy, on the other hand, the RF-surface-touch cooling technology removing the
discomfort and complications by high heat of IPL. Therefore, the effect and safety of E-light
makes a breakthrough.
1.Principle
Applying the technique of IPL and Bi-polar Radio Frequency, the equipment acts on the
entire skin corium and connective tissue, stimulates the collagens of different depth to realign
and grow, then gets treatment effect. Bio-polar RF release energy at the same time, with the
selective absorption for the skin to light energy, various pathological tissues of corium and
epidermis creates Photothermolysis effect. Since light energy is far below conventional IPL, the
pigment tissue and vascular pathological tissue of the corium and epidermis would absorb more
energy without injuring the epidermis, and then remove these pathological tissues better and get
the effect.
2. Application：
1. Hair removal;
2. Skin rejuvenation;Wrinkle removal, fact lifting;
3. Removing freckle, age spots, sun spots, chloasma, pigmentation troubles, etc;
4. Vascular removal;
5. Acne treatment.
3. System Self-checking
The circuit of system entering the self-checking situation when the machine starts, leave
the machine carry on the self-checking for 5-10 seconds, then continue the operation.
4. System Classification
Electric shock protection：Grade1 BF Grade
Corrosion prevention liquid：ordinary
Do not use the machine in the environment mixed of flammable narcotic and air or nitrogen
oxide mixture.
5. Equipment Consist, Specification, and Accessory List

Page 3 , in 12 pages
1. Equipment Consist:
1.1. Mainframe
A. Power supply system
B. Microcomputer system
C. Monitor
D. Cooling System
1.2. E-light Handpiece
A. Intense pulsed light source, xenon lamp
B. Reflector and filter
C. Sapphire wave guide
2. Technique Specification
Light Energy: 1－50J/cm2
RF energy: 1-25J
SR Spectra: 530-1200nm
Cooling: water + air + semi-conductor
Spot size: 8×40mm
N.W.: 35kg
Voltage: 110V±220V 10%, 50~60Hz;
3. Accessory List
Parts List
Ⅱ.
St
handle
Power cord
Fuse
Funnel
Protective goggles
Patch
Key switch

Page 4 , in 12 pages
andard Treatment Process
2.1 Form filling
Fill in the blanks of the Client File, confirm the treatment program, remind the client pay
attention to some points before and after treatment.
2.2 Face cleaning
Clean the face with gentle face cream for 3 minutes.
Remind: clean the hands of operator and the handpiece with bromogeramine.
2.3 Preheating
Start the equipment after face cleaning, preheat for not less than 3 minutes (without lighting
the xenon lamp).
2.4 Shaving
Shave the unwanted hair of the treatment area(2 minutes).
2.5 Gel coating
Coating the gel evenly (2-3mm) on the skin.
Effect：light guide, cooling, anaesthetisin.
Attention: no coating on eyes, eyebrows, lips.
2.6 Eye protection
Operator: wear the safety goggles.
Patient: close the eyes, wear professional safety goggles or cover the eyes with eye patch.
2.7 Allergic test
Emit 2 or 3 light spots in the bottom of ears in safe parameter, observe for 3 minutes.
Effect: do not continue to operate if there is a allergic phenomena.
2.8 Operation
Carry on the operation with a suitable parameter to the operatee.
Attention：
2.8.1 Inform the operatee that there will be a slight pricking in operation before operating, to
avoid panic.
2.8.2 Start the operation with a low energy grade, adjust the parameters in operating while asking
the feeling of the operatee.

Page 5 , in 12 pages
2.8.3 Move the light spot by one spot overlapping the upper 1/3 part of the previous spot.
No emitting one area repeatedly, otherwise may cause inflaming or burns.
2.8.4 The handpiece should touch the skin vertically, no over pressing or leaving the skin.
2.8.5 Observing the reaction of skin while operating.
2.9 Cold compress
Keep gel coating for 20 minutes after operation ending; carry out cold compress in obvious
slight reddish reaction till reddish fading away.
2.10 Cleaning
Clean the gel with cold water, coat corresponding cosmetics.
2.11 Treatment Course
Skin Rejuvenation Program: 30-45 days/time 4 times/course
Hair Removal Program: 2-3months/time 3times/course
2.12 Special reminding
2.12.1 Ask the client before treatment: is there a allergic or not; is there a bad reaction before for
similar operation; fill the Client File concretely. Adjust the parameters on the basis of full
acquaintance of the condition of operatee. Inform the operatee the possible reation in
operation before operating.
2.12.2 In large area treatment or long time continuous operating, the water inside the equipment
will warm up and the handpiece will be hot, interrupt the operation to refresh the water or
leave the water cool down to continue operating.
2.12.3 Refresh the circulating water in one month; use purified water or medical distilled water.
Ⅲ.Operation Instruction
3.1 Before starting the machine
3.1 Accessories connecting：
3.1.1 Connect the handpieces, filters, and probes:
3.1.1.1. Put the handpiece on the hanger
3.1.1.2. Connect the handpiece:
Connect water pipes (2), signal wires (2, black-to-black, red-to-red), xenon lamp wire, and RF
wire to the corresponding jacks on the backboard tightly.
3.1.2 Check the water holes of the backboard, make sure the water outlet hole is plugged well.

Page 6 , in 12 pages
3.2 Water infusing:
3.2.1 pull out the plug of the water inlet hole，insert the water funnel
3.2.2 infuse water till water spill out from the spillway hole.
3.3 Checking
3.3.1 Make sure there is no water leaking;
3.3.2 Make sure there is no moisture or wet for electricity connecting parts;
3.3.3 Make sure the key switch is in the off position;
3.3.4 Make sure the emergency stop switch is in the on position.
3.4 Starting the equipment
3.4.1 Connect the power cord, turn on the key switch;
3.4.2 Double confirm there is no leaking of water circulation, fold the protective cover by
turning it right.
3.5. Debugging
3.5.1. Make sure water and electric circuit is correct connected; then turn on the power to
start the machine.
3.5.2. Turn on the master power switch on the backboard;
3.5.3.Turn on the emergency switch (clockwise turn) in the front side of the mainframe
3.5.4. Turn on the key switch (clockwise turn);
3.5.5. Check is there any leaking of the water connectors.
3.5.6. If the above is checked OK, put the wire cover into the neck on the backboard then
turn deasil to get fixed.
3.6. Operation
Enter operation condition after debugging and no abnormalities found.
3.6.1. Treatment Selecting Interface

Page 7 , in 12 pages
Treatment Selection Interface
Select the wanted treatment program by clicking.
3.6.2. Operation Interface
Operation Interface
Treatment mode: 3 groups of different parameters setting.
Pulse1：working time of the first pulse
Pluses：sub pulse width：irradiating time of other light except the first pulse.

Page 8 , in 12 pages
Delay1: 1st pulse delay: delay time of the first pulse irradiating
Pulse amount adjusting：pulse amount of each irradiating
RF Working time: working time of RF
Repeat frequency：interval between two spots
Total counter: accumulated spot times of the xenon lamp;
Status display:
water circulating status
lamp stauts
charging statu
Current temp
back：return to the previous interface
IPL energy adjusting：increase or decrease the IPL output energy.
RF energy adjusting：increase or decrease the RF output energy.
Cooling adjusting：adjusting the cooling level
pasue/continue: "continue", standby stautus, parameters could be set in this stauts; lamp is on, but could not
make shots.
start/pause: click "start", zimmer the handle and the capacitor charge automatically; system will enter the
treatment status when charge is ready. Click "stop", escape from treatment stauts.
3.8 Treatment Advice
3.8.1 Freckle, age pigment: strong pricking for the first treatment (under the tolerance of the
operatee). One minute after receiving emitting, there will be a slight reddish, which will fade
away in 10 minutes, (for someone special, maybe 30 minutes). Punctuate pigment will appear on
the surface of skin and will be metabolized in 3-7 days. The one-off curing rate of freckles by
using E-light is 60%-80%, normally freckles could be cured in one course of treatment.
Parameter control: Long pulse width, short interval, medium energy.
3.8.2 Chloasma: Light pain, light reddish, redness disappear in 5 minutes. After radiation, the

Page 9 , in 12 pages
pigments become darker first in 10 days, and decline in 15 days. Don ’t adjust big parameter
value to treat chloasma. 1-2 treatment course needed for chloasma.
Parameter control: Short pulse width, long interval, low energy.
3.8.3 Epidermis spot: The most difficult one, so the treatment time is longer correspondingly.
IPL+ is the best way of removing epidermis spot. With the cooperation of using laser, 7-8 times
radiation will cure the spot.
Parameter control: Long pulse width, short interval, medium energy.
3.8.4 Acne scar and other pigmentation: Patient would have a strong pain (under the limit of
patient). Pigmentation will decline in 3-7 days.
Parameter control: Long pulse width, short interval, high energy.
3.8.5 Vascular, redness: Using high pulse width on the basis of easing the skin.
Parameter control: Long pulse width, long interval, suitable energy.
3.8.6 Bulky pore, black head, acne: Strong pain under the limit. Blackhead and oil comeout in
2-3 days, and disappear in 7 days.
Parameter control: Long pulse width, short interval, high energy.
3.8.7 Winkle, pouch, black circle: Light pain.
Parameter control: Short pulse width, long interval, suitable energy.
3.8.8 Skin rejuvenation: Strong pain under the patient limit, reddish; redness disappear in 10
minutes. No suggesting repeat operation.
Parameter control: Long pulse width, long interval, high energy.
3.8.9 Hair Removal: Strong pain, follicular orifice will become a little reddish, with a burning
smell. Caution for arms, lips, and legs hair removal, avoid pigmentation by over high energy.
According to the growing period of hairs, growing period- maturation period-rest period, 3 times
of treatment will remove the hair completely.
Parameter control: Long pulse width, long interval, suitable energy.
Special Attention:
For the sensitive and dark skin, there might be delayed reaction in 24-48 hours, therefore do
not raise the energy casually. Adjust the parameter value according to the whiteness of skin. The
whither, the higher endurance of the skin is. For dark skin, please pay more attention to use long

Page 10 , in 12 pages
interval and suitable energy of parameter value.
Ⅴ.Safety Notice
4.1. Safety of E-light
The equipment takes maximum consideration of the safety of both operator and operatee in
the designing, the following are some safe measures of it:
Circuit self-checking after machine starting;
Using filter/light guide crystal, strong pulse light comes out only from the front side of the
handpiece.
Designed with independent safety circuit, electricity could be shut down automatically when
the IPL power is to high;
Emergency stop switch, shut down the power in emergency;
Key switch to avoid starting the machine by any people;
Use high quality engineering plastic frame, preventing electricity creepage.
【Alarm】
All strong pulsed light device may cause hurt by improper handling. Operators should keep
vigilant and take necessary protection measures according to the manual.
Operatee: Carry out the treatment in the professional treatment room; take effective eye
protecting measure;
Operator: wearing protective glasses;
Treatment room：marked the treatment room clearly with in operating of IPL.
To ensure to the safe use of the equipment, please read the following instructions carefully.
No one except technician authorized by the manufacture could dismantle or repair the
equipment, especially for the power source, handpiece; high voltage electricity inside;
Voltage rating: 110-120V;
Maintaining the equipment after disconnecting the power cord;
Keep the handpiece clean all the time; do not let the gel leaking into the handpiece;
In case leaking of the handpiece, do not start the equipment; already started, turning off
immediately;
No emitting light to one area repeatedly, otherwise may cause inflaming or burns, and may