MYDLINK DCS-8200LH User manual

connected home series
mydlink
QUICK INSTALL GUIDE
HD 180DEGREE WIFI CAMERA
DCS8200LH

If any of the above items are missing, please contact your reseller.
DCS-8200LH HD 180-Degree Wi-Fi Camera
Power Adapter
Package Contents
Mounting Hardware
Minimum Requirements
Mobile Device (to use mydlink Home app)
• iPhone, iPad, or Android smartphone or tablet
(Refer to the mobile app’s store page to see if your device is compatible)
Network Device and Service
• A wireless router (802.11ac/n/g) with Internet service
• An e-mail account (required to create a mydlink® account)
Quick Install Guide
For warranty and regulatory information, please visit:
http://support.dlink.com/warranty.aspx
2
ENGLISH

Product Overview
Camera Lens
Microphone
Power Connector
Reset Button
WPS Button
Front
Back
Camera Stand
Light Sensor
IR LEDs
3
ENGLISH

Mobile App Setup
The camera is compatible with the mydlink Home app, which
allows your camera to work together with other mydlink Home
compatible devices.
To install and congure your camera, follow the instructions from
the Quick Install Card included with your camera.
Launch the app and follow the instructions to
connect and congure your device.
Quick Install Card
Select one of the following methods to
download the mydlink Home app:
• Search for mydlink Home at the iTunes App
Store or Google Play
• Scan the QR code
• Go to http://mydlinkhomeapp.dlink.com
Continue to step 3 on the back of this card.
2
1
4
ENGLISH

Mount the Camera
Please refer to the steps below to assist you with mounting the camera.
We suggest that you congure the camera before mounting.
1
3
2
5
6
4
2. Place the base plate where you want to position the
camera and use a pencil to mark the holes. Make sure the
holes are lined up horizontally.
3. Depending on the material of the wall or ceiling, use proper
tools to drill two holes 25mm deep with a 6mm drill bit
where you marked. If the wall is made out of concrete, drill
the holes first, then insert the plastic anchors to support
the screws.
4. Place the base plate over the holes that are in the wall.
Make sure to align the base plate holes with the holes in
the wall. Use the supplied screws to attach the base plate
to the surface of the wall. Do not overtighten screwheads
as this may crack the mount.
1. Turn the base plate on the bottom of the camera
counterclockwise with a coin to remove it.
5. Place the camera over the base plate and turn the camera
clockwise to lock it in place.
6. Adjust the angle of the camera as desired. When
adjusting the camera, use one hand to hold down the
camera base to prevent it from moving.
5
ENGLISH

1. What is a mydlink No.? What is it used for?
Each camera has a unique eight-digit mydlink No. which will be shown on
the label on the back of your camera. This eight-digit number identies
your device, and is required to add your device to your mydlink account.
2. What can I do if my DCS-8200LH is not working correctly?
• Reset the camera (see next step) and run the setup steps starting
on page 4 again.
• To make sure your hardware is installed correctly, make sure that:
- the power LED is green
- your Internet connection is working
- your router’s LAN & WAN connections are working
- your router supports UPnP®
- your camera is on the same network as your mobile device
- both your mobile device and camera have a working Internet connection
• If your camera is still not working, check your router and make sure it
has the latest rmware.
3. What can I do if I forget my password?
FAQs
If you forget your password, you must reset the
camera. Unfortunately, this process will change
your settings back to factory default. To reset the
camera, locate the reset button on the back of
the camera. With the camera powered on, use an
unfolded paper clip to hold the button down for
10 seconds. Run the setup procedure located on
page 4 once the camera restarts.
4. Why is there a white haze when viewing in night vision mode?
When viewing in night vision mode, the IR lights on the camera may be
reecting o a nearby surface. Try repositioning the camera in order to
avoid glare from IR LEDs.
Reset
Button
6
ENGLISH

Notes
7
ENGLISH

Technical Support
This guide is only for initial conguration. Please refer to the user
manual and FAQs at http://support.dlink.com/DCS-8200LH for more
information. Also feel free to contact us. U.S. and Canadian customers
can contact D-Link Technical Support through our website.
http://support.dlink.com
USA
http://support.dlink.ca
Canada
Version 1.00(US)_90x130
January 19, 2016
290726008200A12
PMQCS960LEX103
Copyright ©2016 All rights reserved. D-Link and the D-Link logo are registered trademarks of D-Link
Corporation or its subsidiaries. Other trademarks are the property of their respective owners. Maximum
wireless signal rate derived from IEEE Standard 802.11ac and 802.11n specications. Actual data
throughput will vary. Network conditions and environmental factors, including volume of network
trac, building materials and construction, and network overhead, lower actual data throughput rate.
Environmental factors will adversely aect wireless signal range. Product specications, size and shape are
subject to change without notice, and actual product appearance may dier from that depicted on the
packaging. Visit dlink.com (US) or dlink.ca (Canada) for more details.