mydome UK113 Operating instructions

Light switch timer
3 step Installation overview
3 minute quick programming guide
A police accredited product
[email protected].uk|0203 637 0856

Important information
Thank you for Purchasing the Light Switch Timer –Please
read the instructions to learn how to install and use your
new timer.
Whilst you will not be accessing or touching any wiring it
is advisable as a precaution to turn off the mains
electricity during installation of the cradle.
The Unit only works on standard type light switches.
It CAN NOT be used on Flat panel switches, Flush mount
switches or dimmer switches.
This unit operates using two fresh, high-quality AA
alkaline batteries
Batteries must be installed for unit to operate.
Use of rechargeable batteries means the low power
indicator may come on immediately.
Contents
Light switch timer unit, cradle, 3 control Wheels, 2 “n”
shaped plastic insert (in bag)

Contents
Installation 4
Setting the time 5
Programming the unit 6
FAQ –Trouble shooting 7
Timer features 9

STEP 1 –Installing the cradle
Turn off the power to the lights at the mains
1 - Using a screw driver, loosen both screws on the
switch plate - Eight to Ten turns of the screw is usually
enough to install the cradle. The screw does not need
to be fully removed.
2 - Slide the cradle between the wall and the switch
3 - Re-tighten the screws –taking care not to over
tighten the screw.
Turn the mains power back on.
Step 2 –install batteries
Insert two (2) high quality AA batteries into the battery
compartment in the rear of the unit as per the polarity
symbols (+ and -) indicated.
The LCD will flash AM 12:00, Mon (Monday), and OFF
STEP 3 –Setting time & Day
Press enter (temperature gauge will disappear)

Press day/ hour / min buttons until correct day &
time is displayed.
Press enter (temperature gauge will reappear)
PS –Be sure to pay attention to the AM /PM indicator.
Step 4 –Programming the unit
Press prog button
Set ON time –by pressing the day/hour/min
press enter
Set OFF time –by pressing the day/hour/min
press enter
Press prog to complete
Ensure the selected days for the ‘Off’programme match the
days for the ‘On’programme otherwise the lights may stay on
for multiple days.
* The timer has the following, convenient different day modes:
Individual day; Week days, Weekends; Every day.
To select multiple days continue pressing the day button. The
user can select groups of days so a single program can turn

lights on every day at the same time.
*the user can repeat for as many programs as they need.
There are 9 possible on/off programmes
Once set the timer will continue to operate and repeat the
program each week
Step 5 –Installing the unit
Slot the unit into the cradle
Press the On and Off buttons to test on /off operation
Aligning the control wheels
The user can then choose how many lights they wish to
control by aligning the wheels provided in the
corresponding slots on the rear of the light switch timer.
The numbers represent positionsof 1,2 & 3 gang switches.
The wheels will click into place - Ensure the wheel fully
clicks into place on both sides.
To Remove Wheels
Users can remove wheels by placing their finger behind
the wheel with the slider in the upper position and pulling
those outwards with their finger behind the wheel.

FAQ & troubleshooting
Why does the light switch timer not turn lights on and off? (‘n’
shaped inserts required)
The gap between the switch and the control wheels is too
large. In order to reduce this gap please use the clear ‘n
shaped’ inserts. This will allow the wheels to contact & roll
over the complete face of your switch.
Day and time
Programme number
‘ON’ time
AM/PM indicator
Auto / manual
indicator
Room temperature
Low Battery Indicator

Remove the cradle by loosening the screws on the switch by a
few turns
• Insert the “n” shaped insert into
the recess of the cradle as shown.
• Re install the cradle.
• Re-tighten the screws and insert
the unit
Note the Inserts sit between the wall and the switch plate –
moving the switch forwards allowing the wheel to make
contact.
Why does the light switch timer do the opposite desired action
(turns lights on when they should be off and off when they
should go on)?
To turn lights on a switch is pressed ‘down’
To turn lights off a switch is pressed ‘up’
If this is not the case on your current set up, then your switch

plate may have been installed upside down. You will need to
rotate your switch 180 degrees. Upon doing so your light
switch timer will function as intended.
How do I reset the timer?
To reset the timer and erase all pre-set programmes, use a
pointed object, such as a straightened paper clip, to gently
press the rest button. The display clears. The LCD will show AM
12:00, MON (Monday), OFF and current room temperature.
NOTE: After resetting you will need to reset the current time
and day.
Why is the light switch timer showing an Error message?
When "Err" (error) displays on the LCD,
Check and remove any obstacles that may be stopping the
back plate from moving.
Remove the batteries from the unit
Wait one minute before reinserting the batteries.
The clock should now show 12:00 and the timer should now
operate as expected. In the unlikely event that you the Error
message reappears your unit may have developed a fault and
will need to be returned to the retailer.

Will the light switch timer work on a 2 way circuit switch plate?
When using the timer on a 2 way circuit it is important to note
the on /off position of the switch will change and as a result
the unit may not operate as expected.
Ensure the switches are in the correct orientation when using
on a two way switch.
To turn lights on a switch is pressed ‘down’
To turn lights off a switch is pressed ‘up’

Using your timer
Using the On/OFF buttons
Normal operation of your lights outside of programmed times
using the “on” and “off” buttons does not impact your pre-
programmed timetable.
Stop the programs from running
Holding the hour button for 7 seconds will cause a bar/line to
appear on top of the word ‘Auto’ on your LCD screen. This
signifies that your programmes are NOT active. The
programmed timetable still remains in the memory of your
light switch timer but will not run. In order to reactivate the
programmes again press the hour button until a bar above the
word ‘Auto’ disappears.

Programming Examples:
The following demonstrate how to set your timer to operate
multiple programmes at a variety of times on various days.
ON 1 MON TUE WED THU FRI SAT SUN 6:15 AM
OFF 1 MON TUE WED THU FRI SAT SUN 8:30 AM
ON 2 MON TUE WED THU 5:30PM
OFF 2 MON TUE WED THU 10:15 PM
ON 3 SAT SUN 9:07 PM
OFF 3 SAT SUN 12:00PM
ON 4WED 10:30 PM
OFF 4 WED 11:48 PM
ON 5 FRI 9:00 PM
OFF 5 FRI 02:00 AM
Be careful not to unintentionally override any of your
programmes by overlapping the times set, especially any
programme for the same day.
When the off times are left blank the unit will remain on till
you turn the light off manually or till the next off cycle.

Clear Programming:
To clear a previous programme Press PROG, you will see the
PROG 1 ON day and time on the screen
Press ENTER to advance to the desired programme number
that you want to remove
Press DAY continually until programme is clear, showing -:- - .
Review Programming
To review your programmed times Press PROG. This will
display the first programmes ON time on the screen
Press ENTER repeatedly to cycle through each ON and OFF
programme settings in sequence.
Activating random mode
Random Night Timer Feature is recommended when you will
be absent from home overnight.
Random mode - a special programme that suggests to would-
be intruders that your home is inhabited, by turning ON your
lights once a night for 3 min at a randomly selected time
between 1:00AM and 5:00AM automatically. The times are

random and different each day of the week.
• Press PROG, press ENTER repeatedly to cycle through the
programmes till you get to PROG 0
• Press ON button to activate the
random programme or press OFF
button to turn off the programme.
• Press ENTER to save
The timer will automatically check
• There are no other programmes to turn the switch ON
between 12:00AM and 6:00AM on that day,
• Your switch is at OFF position on that day (i.e. if you
happened to manually turn on the switch at the Programme 0
activate time, then the programme 0 will skip action on this
day);
NOTE: Modifying or tampering with the timer’s internal
components can cause a malfunction and will invalidate your
guarantee. Operation outside of specification, improper
maintenance, repair, or unauthorized modification.

Guarantee
Your Switched On Products Light Switch Timer (model UK113)
is guaranteed for one year from the date of purchase. Please
retain your receipt as proof of purchase as this will be required
to process any replacements / returns.
This guarantee does not apply to defects resulting from action
of the user such as misuse, improper installation,
Switched On Products liability is limited to repair or
replacement of the product.
Full terms & conditions available on our website
© 2017 Switched on Products Limited
Mydome.co.uk
Designed in the UK

N shaped insert instructions
Only to be used to reduce the gap between switch plate and
light switch timer –details in the guide booklet (FAQ –pg. 8)
Remove the cradle by loosening the screws on the switch by a
few turns
• Insert the “n” shaped insert into
the recess of the cradle as shown.
• Re install the cradle.
• Re-tighten the screws and insert
the unit
Note the Inserts sit between the wall and the switch plate –
moving the switch forwards allowing the wheel to make
contact.