mygroov micromega User manual
User’s manual
!!! IMPORTANT !!! CUSTOMER CARE SAFETY INSTRUCTIONS
IMPORTANT
Please read all instructions before proceeding. If you have any questions
about the operation or use of this product, please contact your dealer.
PRODUCT SAFETY
This unit was designed and manufactured to ensure personal safety. Impro-
per use can result in potential electrical shock or fire hazards. Please retain
these instructions for future reference.
The lightning flash with arrowhead symbol within the equilateral triangle is
intended to alert the user to the presence of non-isolated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to consti-
tute a risk of electric shock.
CAUTION
To prevent the risk of electrical shock, do not remove enclosure or disas-
semble. No user-serviceable parts inside. Refer servicing to qualify service
personnel. The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating, maintenance and
servicing instructions in the literature associated with this device.
AUDIS sarl, 13-15 rue du 8 Mai 1945, 94470 Boissy Saint Leger, FRANCE
Fax: +33(0)1 4382 6128 – www.micromega-hifi.com – VAT: FR07500331301
TECHNICAL CHARACTERISTICS
Audio Characteristics
Cartrige load impedance MM - 47 kΩ/ MC - 100 Ω
Gain MM - 40 dB / MC - 60 dB
THD (1 kHz) ≤0,001% MM, ≤0,005% MC
RIAA deviation < ± 1 dB (20 Hz - 20 kHz)
Frequency response 20 Hz – 20 kHz ± 0,5 dB
ignal to noise ratio ( A weighted) > MM - 88 dB / MC - 76 dB
Mains Power supply
Type of cord C7
Mains voltage range 85 – 265 Vac
Mains frequency range 47 – 63 Hz
Standby consumption (85-265 Vac) < 200 mW
Dimensions
Unit (L x W x H mm) 140 x 150 x 35
Packaging (L x W x H mm) 206 x 201 x 67
Weight
Unit 500 g
Packaging 600 g
WARRANTY
Your MyGROOV is covered by a one year warranty from the date of purchase.
If the device requires servicing, return it to the dealer you purchased it from, packed in the original box
along with the purchase invoice.The warranty covers manufacturing defects, with the exception of any other
damage resulting from:
• An accident, negligent use, poor handling...
• Bad installation and or failure to comply with the instructions in the present manual
• Any servicing carried out by a non-authorized personnel
• Damage during transport (the damage will not be covered by the transporter unless you express the usual
type of legal reservation indicating any damage on delivery)
Notice MYGROOV 140x140 UK.indd 1-3 14/03/13 18:10
AUDIOPHILE MM /MC RIAA PREAMPLIFIER
Dear customer,
Thank you for purchasing a Micromega product. This unit provides ease of use
and sonics of the highest quality. Please pay close attention to this instruction
manual, and read it fully before attempting to operate. It is designed to ensure you
maximise your pleasure of listening to MyGROOV.
Checking
Check that the carton has no damage. Should you have any doubt about its condi-
tion, please do not hesitate to contact your dealer.
Opening the box, you should find:
• One C7 AC Mains cord matching your area.
Mains voltage
MyGROOV is equipped with an internal universal power supply allowing you to use
it with voltage and frequency in the range of 85-265 Vac / 50-60 Hz.
Connections and Power up
Except for the mains cord, MyGROOV is not supplied with any interconnect cables.
To get the best out of your unit, we recommend that you use good quality cables.
Check with your dealer. Following the diagram on the next page, connect your
turntable to MyGROOV inputs. Connect the stereo analog output of MyGROOV to
a line input of your amplifier. While doing this, we recommend you to have your
amplifier turned off. Do not forget to connect the Ground wire of your turntable to
the GND post of MyGROOV.
Plug the AC line cord to the mains input of MyGROOV and then connect the other
end to your wall mains inlet. As soon as MyGROOV is connected to the mains, the
led located under the MyGROOV logo will light up in red indicating that the unit is
in Standby mode.
Operation:
MyGROOV central wheel is used to get out of standby and to set up the input to
match your cartridge model MM or MC.
A Mute position between both inputs and a time delay of 3 seconds guarantees no
noise operation while changing inputs.
Standby
Turn the wheel to the extreme left position.
MyGROOV is then in standby mode and the led located under the MyGROOV logo
turns red. The unit is then respectful of the most stringent ECO regulations.
Cleaning of the unit
1. Unplug MyGROOV from AC mains.
2. Using a soft cloth, gently wipe out the dust from MyGROOV surfaces. To
avoid any damage to the product, never use any solvent or cleaning product
containing solvent such as acetone,trichloroethylene, ...Never use any abrasive
material to clean MyGROOV.
3. Once MyGROOV has been cleaned you can connect the unit to the AC
mains again.
Working conditions
Working temperature : from 0° to 35° C (32° to 95° F)
Storage temperature : from -25° to 60° C (-13° à 140° F)
Relative humidity (working) : from 20 % to 80 %
Relative humidity (storage) : from 10 % to 90 % (without condensation)
Warning
• Do not use MyGROOV near water.
• Do not place objects lled with liquid on or near MyGROOV.
• Do not place MyGROOV near any heat sources such as radiators, stoves or
other heat-generating products including open flames.
• Disconnect MyGROOV during lightning storms or when unused for extended
periods.
• Refer all service-related issues to qualied personnel.
L
R
L
R
85 - 265 V
50-60 Hz
AC MAINS
MADE IN FRANCE
LeftRight
Input
LeftRight
Output GMD
Amplificateur intégré/Integrated Amplifier
Platine/Turntable
Notice MYGROOV 140x140 UK.indd 4-6 14/03/13 18:10
