NAMCO PACMAN AIR HOCKEY 4P User manual

User’s Manual
NOTE
Read this user’s manual carefully before assembling or playing.1.
t for placing or shiftingneiciffussiecapsehterusne,ylbmessaotroirP.2
the product.
Four strong adults are recommended to assemble the product.3.
4. Prior to assembly, inspect and ensure all parts are completely
assembled and secure.
Screw driver
Electric screw driver
Scissors
TOOL
* Note: Self preparation on the tools indicated above
Be careful not to damage the product when using the tools to assemble.
Thank you for purchasing the Namco 4-Player Air Hockey Table. This product is suitable
for 2 or 4 players and we hope you enjoy it! This manual contains detailed information
about how to operate and maintain your game machine properly and safely.
Be sure to read this operation manual before assembling and using your machine to
ensure the safety If the game machine fails to function properly, contact your distributor
or manufacturer for help.
Introduction

List of Parts
Open the cardboard box and EPE(Expanded Polyethylene)
and to ensure the wooden side is facing upwards.
Take out the signboard (1) and the center guard (1).
Use the screw driver to remove the screws on the panel labeled
“ PARTS ” .Once the panel is opened , take out the parts as indicated
below.
Signboard(1)
Key & Screws Storage box
Overhead Bar

List of Parts
Open the base door with this key ,
take all parts out.
Use the key
open door
Signboard
Bracket (2)
16

List of Screws
< X 16 > < X 16 >
< X 2 > < X 2 >
< X 12 > < X 19 >
< X 8 >
Roundhead screw ( 8mm x 25mm )
Legs x 16
Flat washer ( 8mm x 16mm )
Legs x 16
Carriage bolts ( 4mm x 12mm )
Signboard bracket x 2
Iron cap nuts ( M4 )
Signboard bracket x 2
Big flathead screw ( 4mm x 12mm )
Scoreboard x 12
Big flathead screw ( 5mm x 15mm )
Scoreboard bracket x 3
Overhead bar bracket x 12
Center guard x 4
Big flathead screw ( 5mm x 35mm )
Plastic bar bracket cover (black) x 8

Assembly Instruction
Turn the adjuster clockwise to lock the leg.
Install the legs with bolt M8x25(16) and washer M8(16)
as shown in the picture below.
Adjuster
Roundhead screw ( 8mm x 25mm )
Flat washer ( 8mm x 16mm )

Assembly Instruction
4 strong adults are required to turn the table over.
Once the legs are tightly screwed onto the table base , flip and
position the table by 90 degree angle ; then flip it again in the
same manner to conclude with the upright position.
Set table down all four legs at the same time.
Please ensure the ground wire
attached to the floor.
Ground wire

Assembly Instruction
▪Attach the center guard on one side with big flathead screw M5x15mm.
▪As to the other side, insert center guard into the side guards before screw
it tightly.
Screw the side guard on one side with big
flathead screw M5x15mm.
Insert the center guard into one side first ,
then screw the side guard.

Assembly Instruction
Connect the corresponding pins from the cable on bar to the scoreboard.
Connect with the matching color and shape of the pin.
Attach the overhead scoreboard to the bar with two medium screws.
Attach the signboard bracket on the signboard with carriage bolts M4 x 12
and iron cap nuts M4.
Attach the signboard bracket on the scoreboard with truss head screws
M4 x 12.

Assembly Instruction
•Push rubber cover into overhead
bar.
•Pay attention to connecting with
the matching color before insert
the pin.
•Please use M5 x 15 screws , fasten
it into overhead bar bracket , but not
too tight , fasten tight after both sides
are set.
•Insert plastic bar bracket cover in
notch of rubber cover , use M5 x 35
screws , but not too tight.
•Fasten tight after both sides are set.
Combine

Assembly Instruction
After assembly , revolve the adjuster to adjust the height of table.
After assembling completely , open the door beside the coin acceptor
where the mother board installed and set up the game.
mother board installed
and set up the game.

Description on locations of controls
Power Supply :
Supplies the power to motherboard and other control cards.
Separate the power point from +5V and +12V , in order not to influence other
components when power falure or instable.
Caution : Left for +5V ; Right for +12V
PCBoard :
Controls the game operation , light signals and sounds of the machine.
NG component can be read and judged by light on board.
Counters :
Controls the number of games , coins inserted and lottery tickets given .
PCBoard
Power Supply
Counter

Description of light signals and DIP SW
ABCDE
DIP Switch
Adjustment
DIP SW 11
DIP SW 12
ON
1234 5 6 7 8
DIP
ON
1234 5 6 7 8
DIP
Note :
If these lights
are on there
is an error .
Light A: Goal Sensor Signal.
when puck falls, flash light as the signal. If light stay on, it might be stuck by
Debris, shaving, paper lodged inside the return unit. or, Release Solenoid
needs to be replaced.
Light B: Start button signal.
No function, it may be ignored.
Light C: Coin mechanism light signal.
when coin insert, flash light as the signal. if the light stay on, it is an error
setting on NC, NO button, Coin Acceptor must be setting on N.O.(normally open)
Light D: Ticket light Signal. when dispenser is sensed, flash light as the
signal. if the ticket dispenser keeps running and no stop, it might be error on
adjustment of 0,+5 or NO, NC, it should be on “0” and “NO”.
Light E: Strike light sigal. when puck hits rail, the sounds is made and flash
light as signal. if the light stay on, adjust VR till light is off.

Description of light signals and DIP SW
DIP SW 11
DIP Switch 1,2 and 3 adjust the numbers of
inserted coins and game rounds.
DIP Switch 4,5 and 6 adjust the numbers of
lottery ticket.
DIP Switch 7 and 8 adjust the numbers of
sound strikes ; there are 3 types of sound
effect.
DIP SW 12
DIP Switch 1,2 and 3 adjust the numbers of
balls ( each round ).
DIP Switch 4,5,6 adjust the numbers of
time ( each round ).
DIP Switch 7 for lottery ticket exit slot :
the lottery ticket is given when winning , or
ticket number are given to both slots upon
winning more and less for the other.
This DIP Switch is failed in function onece the
ticket is not given.
DIP Switch 8 is for demo sound:
Option for sound or non sound when the
machine standby.
DIP SW 11
DIP SW 12

Explanation and Analysis of machine components
Power Supply Transformer
Platform connected
to Main body Power switch box
Counter Scoreboard

Notices during Use and accessory disassembling
1. Watch for the power plug load during use to avoid short or fire.
Do not overloading.
2. The power supply wire should be securely fixed to prevent
stepping on or tripping.
3. This product is an electronic game;keep children off from power
source plug. During the operation of this electronic product ,
adults shall give warning and monitoring to reduce risk.
4. Keep table surface always clean and avoid dust covered.
5. Do not use any sharp object to scrape the table surface to
avoid the scratch.
6. Please change a new puck when it does not move fluently
during the game.
7. Please check the holes if the puck goes slowly or stop in a
certain place when playing.
8. when problems occur as below , do not try solve or repair on
your own. Contact electricians for repair.
* Operational failure of fan motor damage.
* Problems of power source wire or plug;
* Liquid on the surface or foreign object is found in the motor.
* Abnormal sound is detected during the operation of the fan
motor.
9. When machine goes error or abnormality , operation must be
stopped , inspection technician is advised.
10. Adjust the adjustable bolt if necessary to keep table in horizontal
position.
11. Be sure to avoid shaking when transport / loading.
12. Avoid wetness when placed out door.
13. Avoid wetness when placed in basement or special place.

Notices during Use and accessory disassembling

Care and Maintenance
1. Please use a soft dry cloth and polishing spray to clean the table
surface . DO NOT APPLY WATER.
2. Wax the table surface periodically to ensure smooth air hockey
play.
3. Clean out the objects stuck in ventilation holes with a pin.
4. Open the puck released door to clean the track of balls to
prevent them from becoming stuck.
5. Dirt on the pcboard shall be cleaned with a soft brush.
Do not use water or a wet cloth to clean it .
6. The score board shall be cleaned with a cloth and keep dust free.
7. Clean body and rails with soft , dry and waxed cloth.