3| 4datasheet-FA220C-1704-en.1.1
Mode d: While character A or C is flashing, shore press ▼or ▲unitl digit d flash.
6) Parameter setting (Switching wind speed to wind scale is not linear, wind speed number has a little change when switch wind speed to
wind scale.)
(In mode setting, short press and move the cursor to the required position, then short press ▼or ▲
to change the number, when the
setting is compeleted, press SET button for 3 seconds to save and quit.)
2. Wind direction setting
Product displays 16 wind direction. In normal mode, press a second, enter into wind direction mode, it displays 0~359 degree and 16
wind direction; press a second again, quit wind direction mode, return to normal mode (see fig. 6).
3. Setting timing system and checking
Time service is used for SD card data logger; there is no need to set when you do not request record data.
If require data logger, power interrupts over 6 months or used in another time zone, please set the time.
Manual or auto set time (auto set should only be achieved by NANHUA’s software)
Manual set process:
1) Under A mode & inputting password “A16.3”, turns to time set and shows access time.
2) Under time set mode, displays “1—12”,and “1” flashes, which means year-2012
3) Then press▲, displays “2—02”,and “2” flashes, which means month-February;
4) Then press▲, displays “3—24”,and “3” flashes, which means date-24th
5) Then press▲, displays “4—13”,and “4” flashes, which means H-13;
6) Then press▲, displays “5—58”,and “5” flashes, which means Min-58
7) Then press▲, displays “6—26”,and “6” flashes, which means Sec-26
8) Press ▲or▼, you can re-check the time. Once the tolerance is over 3 mins, please revise the time; otherwise wait 10s and quit.
9) Setting device timing system, short push to move cursor, short push ▲or▼to revise data, finish se
tting push SET button 3S to save
and quit.
SD card data logger:
1) Under normal mode and SD card inserted, the displayer will take sample with 10s interval and store it into SD card per 20 mins and so
forth.
2) SD card storage format:
★Total folder “WINDYDAT”under SD card directory
★Year folder “YEAR20xx” under“WINDYDAT”
★Monthly folder “MONTHxx” under “YEAR20xx”
★Day folder“DAYxx.TXT” under“MONTHxx”
★Each day’s data stored under “DAYxx.TXT”. Ex. 15:01:30 167 230 means the wind speed is 16.7m/s and direction of 230°at 15:01:30 of
that day.
3)SD card Operation and troubleshooting:
★Once the SD card extracted, the displayer screen will flash 4 times with buzzing, which mean the SD card is extracted.
★Once the wrong SD card inserted, the displayer screen will flash 4 times with buzzing, which means the SD card faults.
★If the normal SD card inserted, the displayer screen will not flash but alarm once, which means the SD card is right.
★SD card problems and solutions:
①SD card write-protection: unlock the SD card write-protection.
②SD card capacity less than 30M: ensure the capacity is over 30M.
③Before SD card used, please format it as FAT32 file system.
④If the SD card meets above requirements but the displayer also shows SD card fault, please re-start the displayer.
4) SD card and principal computer analysis software:
★Attached 4G standard SD card.
★4G SD card has store FA220C computer analysis software, software manual, USD to RS485 UT890 driver software.
Nos. Parameter Value
1 Wind speed range 0~50m/s
2 Pre-alarm 18m/s, scale 8
3 Alarm 22m/s, scale 9
4 Display Wind speed
Caution:
1. L on g p r es s ▼ a n d ▲ f or 3 s e con d s to r e s e t p r o d u ct to fa cto r y
default configuration.
2.Entering into or quitting parameter setting and resting product to
factory default configuration come with a “Di” sound.
