National Instruments SCXI SCXI-1102 Manual

CALIBRATION PROCEDURE
SCXI -1102/B/C
For NI-DAQmx
This document contains information and instructions for calibrating the
National Instruments SCXI-1102/B/C signal conditioning module.
Contents
Conventions ............................................................................................ 2
Software .................................................................................................. 2
Documentation ........................................................................................ 3
Calibration Interval ................................................................................. 3
Password ................................................................................................. 3
Test Equipment ....................................................................................... 4
Test Conditions ....................................................................................... 4
Calibration Process ................................................................................. 5
Initial Setup...................................................................................... 5
Verification Procedure ..................................................................... 7
Adjustment Procedure...................................................................... 12
Verifying Adjusted Values .............................................................. 14
Test Limits .............................................................................................. 14
Gain and Offset................................................................................ 15
SCXI-1102/B/C Front and Rear Panel Diagrams ................................... 15
World Wide Support and Services.......................................................... 18
™

SCXI-1102/B/C Calibration Procedure 2 ni.com
Conventions
The following conventions are used in this document:
»The »symbol leads you through nested menu items and dialog box options
to a final action. The sequence File»Page Setup»Options directs you to
pull down the File menu, select the Page Setup item, and select Options
from the last dialog box.
This icon denotes a note, which alerts you to important information.
bold Bold text denotes items that you must select or click in the software, such
as menu items and dialog box options. Bold text also denotes parameter
names.
italic Italic text denotes variables, emphasis, a cross-reference, or an introduction
to a key concept. Italic text also denotes text that is a placeholder for a word
or value that you must supply.
monospace Text in this font denotes text or characters that you should enter from the
keyboard, sections of code, programming examples, and syntax examples.
This font is also used for the proper names of disk drives, paths, directories,
programs, subprograms, subroutines, device names, functions, operations,
variables, filenames, and extensions.
monospace italic Italic text in this font denotes text that is a placeholder for a word or value
that you must supply.
Software
The SCXI-1102/B/C calibration procedure requires the NI-DAQmx driver.
NI recommends using the latest driver that supports both your development
environment and the SCXI-1102/B/C. NI-DAQmx includes high-level
function calls to simplify the task of writing software to calibrate devices.
NI-DAQmx supports many programming languages, including LabVIEW,
LabWindows™/CVI™, C/C++, C#, and Visual Basic .NET.

©National Instruments 3 SCXI-1102/B/C Calibration Procedure
Documentation
The following documents are the primary references for writing your
calibration utility:
• The NI-DAQmx Help includes information about creating applications
that use NI-DAQmx.
• The NI-DAQmx C Reference Help includes information about the
functions in NI-DAQmx.
• The DAQ Getting Started guides include information about installing
and configuring NI-DAQmx devices.
You can access these documents by selecting
Start»All Programs»National Instruments»NI-DAQmx after installing
NI-DAQmx.
For more information about the SCXI-1102/B/C, refer to the
SCXI-1102/B/C User Manual. For information about installing and
configuring SCXI modules, refer to the SCXI Quick Start Guide.
Calibration Interval
Calibrate the SCXI-1102/B/C at a regular interval as defined by the
measurement accuracy requirements of your application. NI recommends
that you perform a complete calibration at least once every year. You can
shorten this interval based on the accuracy requirements of your
application.
Password
The default password for password-protected operations is NI.

SCXI-1102/B/C Calibration Procedure 4 ni.com
Test Equipment
NI recommends that you use the equipment in Table 1 to calibrate the
SCXI-1102/B/C. If these instruments are not available, use the
requirements listed in Table 1 to select a suitable substitute.
Test Conditions
Follow these guidelines to optimize the connections and the environment
during calibration:
• Keep connections to the SCXI-1102/B/C as short as possible. Long
cables and wires can act as antennas, picking up extra noise and
thermal offsets that affect measurements.
• Use shielded copper wire for all cable connections to the
SCXI-1102/B/C. Use twisted-pair wire to eliminate noise and thermal
offsets.
• Maintain the ambient temperature between 18 °C and 28 °C.
• Keep relative humidity below 80%.
• Allow a warm-up time of at least 15 minutes for the SCXI-1102/B/C
and 30 minutes for the DAQ device to ensure that the measurement
circuitry is at a stable operating temperature.
Table 1. Test Equipment
Equipment
Recommended
Model Requirements
Calibrator Fluke 5700A 50 ppm
DAQ Device NI 6281 16-bit minimum
DMM NI 4070 6 1/2 digit, 15 ppm
Terminal Block SCXI-1300 —

©National Instruments 5 SCXI-1102/B/C Calibration Procedure
Calibration Process
The calibration process has the following steps:
1. Initial Setup—Configure the SCXI-1102/B/C for calibration.
2. Verification Procedure—Verify the existing operation of the
SCXI-1102/B/C. This step determines whether the SCXI-1102/B/C is
operating within its test limits.
3. Adjustment Procedure—Perform an external calibration that adjusts
the SCXI-1102/B/C calibration constants with respect to a known
voltage source.
4. Verifying Adjusted Values—Perform another verification to ensure
that the SCXI-1102/B/C is operating within its test limits after
adjustments.
Initial Setup
Complete the following steps to configure the SCXI-1102/B/C for
calibration:
1. Make sure that all the appropriate driver and application software is
installed.
2. Make sure all components involved in the calibration procedure are
powered off.
3. Assemble the SCXI-1102/B/C, SCXI chassis, terminal blocks, and
DAQ device as shown in Figure 1. You must cable the SCXI-1102/B/C
directly to the DAQ device.

SCXI-1102/B/C Calibration Procedure 6 ni.com
Figure 1. Calibration Connections
4. Power on the SCXI chassis and the external computer.
5. You must configure the hardware properly with Measurement &
Automation Explorer (MAX). Refer to the SCXI Quick Start Guide for
details about configuring the SCXI chassis.
Note When you configure a device in MAX, the device is assigned a device identifier. In
this calibration document, the functions used for demonstrating the calibration process use
the device identifiers Dev1 for the DAQ device and SC1Mod1 for the SCXI-1102/B/C.
1 SCXI-1300 Terminal Block
2 SCXI-1102/B/C Module
3 SCXI Chassis
4 SCXI-1349 Cable Adapter
5 Shielded 68-Pin Cable
6 NB1 Cable (50-Pin Ribbon Cable)
7 TBX 50-Pin Terminal Block
8 Cable to DMM
9 Cable to Calibrator
10 Calibrator
11 DMM
12 DAQ Device
®
5
4
3
2
1
ADDRESS
SCXI1100
2468 10 12 1416 18 20 20 24 26 28 30 32 34 36 38 40 42 44 46 48 50
13 5 7 911 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49
3
1
2
4
5
7
8
11
6
9
12
10

©National Instruments 7 SCXI-1102/B/C Calibration Procedure
Verification Procedure
The verification procedure determines how well the SCXI-1102/B/C is
meeting its test limits. You can use this information to select the
appropriate calibration interval for your application.
The SCXI-1102/B/C stores gain and offset calibration constants for each
gain setting per analog input channel. A complete verification of the inputs
involves measuring the accuracy at all possible gain settings on all channels
of the SCXI-1102/B/C.
To view the calibration VIs in LabVIEW, select Measurement
I/O»DAQmx - Data Acquisition»DAQmx Advanced»DAQmx
Calibration on the Functions palette. You can also use the Search button,
shown in Figure 2, to look for a specific VI.
Figure 2. DAQmx Calibration Palette and the Search Button

SCXI-1102/B/C Calibration Procedure 8 ni.com
Complete the following steps to verify the accuracy of each
SCXI-1102/B/C analog input channel:
1. Use the DAQmx Self Calibrate VI to verify the DAQ device. This VI
measures the onboard reference voltage of the DAQ device and adjusts
the self-calibration constants to account for any errors caused by
short-term fluctuations in the operating environment.
Note Throughout the verification procedure, refer to the function call parameters for the
LabVIEW input values.
2. Connect the calibrator output to pins AI– and AI+ for all channels.
Refer to the SCXI-1300/1301 Terminal Block Installation Guide for
connection instructions. If you are not using the recommended
SCXI-1300, refer to Table 8 for the front signal pin assignments of the
SCXI-1102/B/C. If the calibration signal source is floating, connect
AI – to the SCXI chassis ground using the ground lug available on the
SCXI terminal block.
3. Set the calibrator voltage to the desired test point indicated in
Tables 6 or 7.
4. Create a task using DAQmxCreateTask.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxSelfCal with the
following parameter:
Device_Name:"Dev1"
LabVIEW Block Diagram NI-DAQmx Function Call
LabVIEW does not require
this step.
Call DAQmxCreateTask with the
following parameters:
taskName: "AIVerificationTask"
taskHandle: &taskHandle

©National Instruments 9 SCXI-1102/B/C Calibration Procedure
5. Add a voltage channel using the DAQmx Create Virtual Channel VI.
6. Set the gain value to 1 or 100 using the DAQmx Channel Property
Node. You can find the AI.Gain property by selecting Analog
Input»General Properties»Advanced»Gain. Use the gain setting
that corresponds to the current test point.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxCreateAIVoltageChan with the
following parameters:
taskHandle: taskHandle
physicalChannel: "SC1Mod1/aiX"†
nameToAssignToChannel: "myVoltageChannel"
terminalConfig: DAQmx_Val_Cfg_Default
minVal: -10 V
maxVal: 10 V
units: DAQmx_Val_Volts
customScaleName: ""
†Where Xrefers to the channel you are verifying.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxSetAIGain with the following
parameters:
taskHandle: taskHandle
Channel: ""
Data: (gain value for particular test
point) float64

SCXI-1102/B/C Calibration Procedure 10 ni.com
7. Configure timing for the voltage acquisition using the DAQmx
Timing VI.
8. Commit the verification changes using the DAQmx Control Task VI.
9. For each new test point, use the Time Delay Express VI to account for
the settling time of the SCXI-1102/B/C. Refer to Table 2 for the
settling time of the SCXI-1102/B/C.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxCfgSampClkTiming with the following
parameters:
taskHandle: taskHandle
source: ""
rate: 1000.0
activeEdge: DAQmx_Val_Rising
sampleMode: DAQmx_Val_FiniteSamps
sampsPerChan: 1000
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxTaskControl with the following
parameters:
taskHandle: taskHandle
action: DAQmx_Val_Task_Commit
Table 2. Settling Time of the SCXI-1102/B/C
SCXI-1102 SCXI-1102B, SCXI-1102C
3 minutes (first test point)
1 minute (all other test points)
5 second
LabVIEW Block Diagram Function Call
Call a sleep or wait function to suspend
execution for the necessary settling time listed
in Table 2.