Nature Power 23401 User manual

Version 1.2
120 LED DUAL HEAD
SOLAR MOTION LIGHT
Instruction Manual
Item# 23401

Page of 7
2
Thank you very much for choosing a Nature Power Product! For future reference, please complete the
owner record below:
Model: _______________ Purchase Date: _______________
Save the receipt and these instructions. It is important that you read the entire manual to become
familiar with this product before you begin using it.
This machine is designed for certain applications only. The distributor cannot be responsible for issues
arising from modification. We strongly recommend this machine not be modified and/or used for any
application other than that for which it was designed. If you have any questions relative to a particular
application, DO NOT use the machine until you have first contacted the distributor to determine if it can
or should be performed on the product.
For technical questions please call 1-800-588-0590.
GENERAL SAFETY RULES
WARNING:
Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow
the safety rules and other basic safety precautions may result in serious personal injury.
CAUTION:
Do not allow persons to operate or assemble this solar light until they have read this manual and have
developed a thorough understanding of how the solar light works.
WARNING:
The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible
conditions or situations that could occur. It must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS
FEATURES
Your Solar Motion Light is the perfect system for following:
Entrance
Garage
Porch
Eaves
Emergency

Page of 7
3
PARTS LIST
Part
Description
1
Lamp
2
Solar Panel (16 ft. wire)
3
Screws & Anchors
4
Mounting Bracket
5
Manual
Battery included, not a part
USE AND CARE
Do not modify the solar light in any way. Unauthorized modification may impair the function and/or safety
and could affect the life of the equipment. There are specific applications for which the solar light was
designed.
Always check for damaged or worn out parts before using the solar light. Broken parts will affect the solar
light operation. Replace or repair damaged or worn parts immediately.
Store idle solar light. When solar light is not in use, store it in a secure place out of the reach of children.
Inspect it for good working condition prior to storage and before re-use.
ASSEMBLY
1. Lamp Unit Installation
Mounting your light requires a screwdriver, pencil and (in some circumstances) a power drill.
Place the mounting bracket on the surface you wish to mount to.
Mark with a pencil the position of the mounting bracket screw holes (3). This will enable you to pre-drill
your screw holes.
Once the mounting bracket is installed, ensuring all screws are tight, you are ready to position your 120
LED Ultra Bright Motion Light.
Carefully route the wire from the solar panel to the lamp and plug it into the power socket.
Adjust the motion sensor to your desired position. Your 120 LED Ultra Bright Motion Light is now
installed and ready to charge.
Note: Lamp unit should be mounted 6.5 ~ 9.8ft from the ground to ensure motion detection is optimized.
2. Solar Panel Wall or Roof Mounted Installation
Choose an area that receives the maximum amount of sunlight possible.
Use the holes located on the solar panel mounting bracket to mark the mounting surface for
installation.
Set the bracket on the surface you have chosen and secure it in place with the 3 screws and anchors
provided.
Adjust the angle of the Solar Panel to ensure it receives optimum sunlight.
Note: The Solar Panel is equipped with a 16 ft. wire. The maximum distance between the lamp unit and solar
panel can be 16 ft.

Page of 7
4
ASSEMBLY DIAGRAM
OPERATION
1. Before the Solar Motion Light can operate to its full capacity, the Solar Panel needs to be in sunlight for 3 days
to fully charge the included battery. Charging should be done with the unit in the “OFF” position.
2. Located at the bottom of the Battery Housing (11) there is a switch with three positions:
Turn the switch to “AUTO” position, the light will turn on automatically at night when motion is
detected by the Motion Detector Head (6).
Turn the switch to “ON” position, the light can be used as a standard light for constant illumination.
Turn the switch to “OFF” position, the light will remain off and will not detect any movement.
3. The lamp heads and arms are adjustable:
Part
Description
Part
Description
1
Lamp
9
Power Socket
2
Solar Panel (16 ft. wire)
10
Solar Panel Mounting Bracket
3
Screws & Anchors
11
Battery Housing
4
120 LED’s
12
Coupling Shaft
5
Mounting Bracket
13
LUX Adjusting Knob
6
Motion Detector Head
14
SENS Adjusting Knob
7
Arm
15
TIME Adjusting Knob
8
ON/OFF/AUTO Switch
16
NI-MH Battery Pack (not shown)

Page of 7
5
Both arms can be rotated 180º front and back.
Coupling Shafts can be rotated 180º horizontally.
Both lamp heads can be rotated 180º left and right.
Adjust these parts and joints to reach
optimum angle and range of illumination.
4. The Motion Detector Head is adjustable:
Coupling shaft can be rotated 180º up and down.
The joint connecting to the Battery Housing can be rotated 180º
left and right. Adjust these joints to reach optimum angle
and range of detection.
NOTE: Light will function when the photo-sensor senses minimal light.
HOW TO USE CONTROL DIALS
The Solar Motion Light has 3 different control dials which control the light’s duration,
sensitivity to light and sensitivity to motion.

Page of 7
6
LUX (LIGHT LEVEL)
1. The LUX Adjusting dial (13) tells the sensor the level of darkness that must be reached before the light turns
on.
2. If set to the maximum level, the light will go on in daylight.
3. If set to the minimum setting the sensor will only trigger the light to turn on at dusk or when it is dark
out. This is the ideal position for general usage.
TIME
1. The TIME Adjusting dial (15) sets the duration of illumination time.
2. The TIME is adjustable from 8 seconds to 2 minutes. Rotating the dial clockwise will increase the
illumination time.
SENS (SENSITIVITY)
This determines the range of motion detection:
1. Mid position - Normal setting.
2. Maximum position - Maximum range.
LOCATION OF SOLAR PANEL
For best results, please locate your solar panel in a
position where it can absorb direct sunlight on the solar
panel, and generally free from cover and shade.
TROUBLESHOOTING
If the Solar Motion Light does not illuminate when movement in front of the sensor is obvious, please observe
the following:
Ensure the solar panel is in a location where it will receive maximum sunlight during daytime hours.
Ensure the lamp head is away from other light sources. Other light sources at night will prevent the
unit from turning on.
Ensure switch is set to “AUTO” position.
Check batteries are installed correctly.
Allow the solar panel to charge the batteries in direct sunlight for 3 days with the switch in the
“OFF” position.
Replace Batteries.
Note: Rechargeable batteries may last up to 600 charges. For best performance replace batteries every 12
months.

Page of 7
7
MAINTENANCE
Maintain your solar light. It is recommended that the general condition of any solar light be examined before it is
used. Clean the solar module with a damp towel to ensure optimum performance of the solar light. Do not use any
type of solvent for cleaning and be careful not to put too much pressure on the module while cleaning.
BATTERY REPLACEMENT
1. The Battery Pack is located in the Battery Housing (11).
2. Turn the Switch (8) to the “OFF” position. Remove the four screws from the Battery Housing (11). Separate
the Battery Pack connector. Remove old Battery Pack. Replace only with identical rechargeable Battery Pack
(16).
3. Check correct polarity of battery replacement.
4. Replace the cover of the Battery Housing (11). Secure it with the four screws.
LIMITED WARRANTY
Nature Power warrants our products to the original purchaser that this product is free from defects in materials
and workmanship for the period of one year from date of purchase.
Dated Proof of Purchase is required.
Please contact Nature Power Products to acquire more information or technical support:
1-800-588-0590
[email protected]
www.naturepowerproducts.com