Nauticam Macro to Wideangle Lens 1 User manual

Current as of 2018-10-19
Instruction Manual for
Marco to Wideangle Lens 1 (MWL-1)
150 deg. FOV with Full Frame 60mm Marco
Lenses
PN# 86201
FOREWORD
Thank you for your purchase of a NAUTICAM product.
At NAUTICAM, we pride ourselves in the ability to recognize the
requirements of professional as well as amateur underwater photographers
and fulfill them through the innovative designs of our products. We strive to
achieve a high level of user-friendliness by allowing stress-free installation and
easy operation of all important functions of the camera.
Each product is individually inspected and water pressure tested to
ensure optimum quality.
Please read this manual carefully before using the product, this will
maximize its performance as well as its lifetime.
WARRANTY
All NAUTICAM Housing Products and Viewfinders are warranted against
any material and manufacturing defects for two years from the date of
purchase for consumer use. NAUTICAM Optical Accessories are warranted
against material and manufacturing defects for a period of one year, and
HDMI cables carry a four month warranty.
This warranty only applies to products purchased from authorized
NAUTICAM dealers and does not extend beyond the original retail purchaser.
To return your product for service, please contact your regional
authorized service center(s). Please note that this warranty only applies
when the product is purchased in the territory where the service center is
located.
NAUTICAM does not hold responsibility for damage, of any nature, to any
equipment used with and/or placed within our products.
NAUTICAM accepts no liability for any loss of captured images or the
inability to capture images even if it is due to the malfunctioning of our
products.
Unauthorized modifications and/or repairs of our products will
automatically invalidate the warranty.
PACKAGE CONTENTS
Marco Wideangle Lens 1 (MWL-1)
M67 to Bayonet Mount Converter (#83213)
Rear Lens Cap for MWL-1/WWL-1 (#83221)
Bayonet Mounting Ring for MWL-1(Pre-installed)
Neoprene Cover
Cleaning Cloth
Carrying Bag
Instruction Manual and Compatibility Chart
IDENTIFICATION OF PARTS
* There are two alignment pins at the bottom of the holder, by relocating the two screws
to the threaded holes around the holder, the position of the holder can be changed
MOUNTING AND UN-MOUNTING THE LENS
The MWL-1 comes with M67 to Bayonet mount converter.
Please refer to next section in order to convert M67 threaded port to Bayonet
mount system.
To mount the M67 to bayonet converter on Macro port before attaching
the MWL lens.
Align the two positioning pins on the back of the converter with the slots on
the front of the port. Fasten the converter on the front of the port with the
tool provided.
To mount the lens on a port with bayonet mount system:
Align the “I” mark on the lens with the “I” mark on the converter and then push it in.
--- Continue on next page ---
Eyelet for lanyard
Alignment “I” mark
Thumb screws
for lens hood
(4x)
Lens hood
Bayonet mounting ring
Lens alignment
dot
Lens release
button
Fastening
tool
Positioning pins
(x2)
Threaded holes for
positioning pin* (x6)
M67 thread
All manuals and user guides at all-guides.com
all-guides.com

Current as of 2018-10-19
--- Continue from front page ---
Turn the lens clockwise until the “I” mark on the lens aligns with the WHITE
dot on the converter and a “click” sound is heard.
To un-mount the lens from port:
Press and hold the RED lens release button and then turn the lens anti-
clockwise.
Remove the lens when “I” mark on the lens aligns with the “I” mark on the
converter.
ADJUSTING THE LENS HOOD POSITION
To adjust the position of the lens hood, slightly loosen the four thumb screws
as indicated above (one is not visible from the image). Turn the hood to the
desired position and secure by tightening the four thumb screws.
CARE AND MAINTENANCE
The following procedures are advised to be followed:
The MWL-1 should be rinsed thoroughly in fresh water after each dive.
Dry and clean the glass surface of the MWL-1 with the cloth provided.
Cover the lens with the provided covers when not in use.
DO NOT use any kind of abrasive solutions to clean the glass surfaces.
OPTIONAL ACCESSORIES
86221 M67 Flip holder for MWL-1
86222 M67 Double Flip holder for MWL-1
83214 Bayonet Mount Holder for SMC/CMC
83222 Bayonet Mount Lens Holder for Arms
83223 Bayonet Mount Double Lens Holder for Arms
83227 Bayonet Mount Lens Holder for Inon Float Arms
72231 Single Bayonet Lens Holder for 70mm Nauticam Carbon Fiber
Aluminum Float Arms
72232 Double Bayonet Lens Holder for 70mm Nauticam Carbon Fiber
Aluminum Float Arms
72241 Single Bayonet Lens Holder for 90mm Nauticam Carbon Fiber
Aluminum Float Arms
72242 Double Bayonet Lens Holder for 90mm Nauticam Carbon Fiber
Aluminum Float Arms
SPECIFICATIONS
Lens Construction:
7 elements in 5 groups(inc. one aspherical element)
Field of view:
(Underwater)
150°(Ref. 60mm equiv.)
Focal distance:
0cm to infinity
Dimensions:
Dia108mm x 120mm
Weight:
(Air/ Underwater)
1.20kg / 0.58kg
Depth rating:
100m
Mount system:
M67 or NA Bayonet
Body construction
Hard-anodized aluminum alloy
Lens coating
Both side anti-reflection coating
Please visit www.nauticam.com for the latest MWL-1 compatibility chart.
Remark: All Nauticam product manual will be changed to e-manual in end of
2018. Please download corresponding product manuals on Nauticam.com
website, or contact us for e-manuals.
Press and hold
All manuals and user guides at all-guides.com