Nav TV NTV-KIT217 User manual

1 |
P
A
ud
1
2
3
4
To rem
1
2
3
P
age
Agreement: End
u
io/Video inp
. Using a soft
2. On the drive
3. Once both p
screwdriver
4. With both ve
C
move the vents y
. Inside the ve
place. There
2. Insert the fo
right (horizo
key is insert
3. Once both k
release the c
the vent to h
u
ser agrees to us
e
If yo
u
ut and VIM
f
Reten
plastic pry tool,
er’s side, to the ri
panels have been
or plastic tool, si
ents removed, re
Cayenne Rad
you will need a pa
ent you will see 4
ewill be 2 on eith
rd keys into the v
ntally). The clasp
ed be sure that i
keys are in place
clasps. You may
help “work” out th
this product in co
m
u
do not agree, ple
a
3590 NW 12th Ave. Coral Springs, FL 33065
f
or 2010 an
d
ntion Clips
gently pry off the
ght of the steerin
nremoved, find a
imultaneously de
emove 2 T27 TOR
dio Removal
air of Ford radio
4plastic clasps h
her side of the ve
vent with one sid
ps have an open
t goes through th
, squeeze the ke
yneed to insert a
he vent.
m
pliance with all S
t
a
se discontinue us
www.nav-tv.c
o
PCM3.1 AV 970
NTV-KIT217
d
up Porsch
e
with th
e
Panamer
etrim panel abov
ng column and to
and identify 2 ret
epress the clips w
RX screws on ea
removal keys.
holding the vents
ent.
de on the left and
nback, so when t
he clasp.
eys together to
aplastic tool und
t
ate and Federal la
w
e immediately and
TEL 56
1
o
minfo@n
a
e
Panamer
a
e
PCM3.1 r
a
ra Radio Rem
ve the glove box.
othe left of the H
tention clips on e
while pulling out
ach side of the ra
sin
d
the
der
w
s. NAV-TV Corp.
return product to
p
1-955-9770 FAX
a
v-tv.com
a
and 2011
P
a
dio.
moval
.Start at the bott
HVAC vent, gentl
each side toward
the vents.
adio, then pull the
would not be held
p
lace of purchase.
561-955-9760
P
orsche Ca
y
tom of the panel
y pry off the trim
the back of each
eradio straight o
Removal of
liable for misuse
o
y
enne vehicl
and work around
panel.
hvent. Using a f
out.
fVent
o
f its product.
es equippe
d
dand remove.
flat blade
d
08/20/14
NTV-DOC116
rB2
Kit Contents
CAN Adapter Harness
NTV-HAR058
Radio T-Harness
NTV-HAR111
MOST Fiber
NTV-ASY03 AV Interface
VTC-970 Filter
USB Cable
NTV-CAB009
AV Harness
NTV-HAR055
Male to male barrel
NTV-CON018
MOST In-Line Fiber
NTV-ASY195

2 | Page
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.
If you do not agree, please discontinue use immediately and return product to place of purchase.
Installation
1. Disconnect the factory 40 pin plug from behind the radio and plug it into
the supplied aftermarket 40 pin adapter harness.
2. Unplug the fiber optic cable from the factory 40 pin plug. *Assemble the
supplied fiber optic cable into the M.O.S.T. loop in the order pictured
below then reinsert the optic cable into the supplied 40 pin plug in the
same location as you removed it from on the factory connector (radio
side). Plug in the new fiber terminal into the supplied OPV-970 board.
3. On the OPV-970 power harness, find a reliable continuous power and
ground connection. Connection at the T-harness is recommended (All
connections should be soldered and insulated). Red is power and Black
is ground.
4. The supplied T-harness will have a pair of RCA’s plugged into each
other. Disconnect these two RCA’s
5. Connect the “VIDEO OUT” cable of the OPV to the RCA going towards
the radio (female).
6. Connect the “CAM IN” cable of the OPV to the RCA going towards the
car (male). #
7. Connect the external AV source to the OPV-970.
8. Plug the VTC-970 into the 8 pin Molex connector of the T-harness.
9. Insert the radio side of the supplied T-harness into the radio.
10. Test then reassemble.
*Follow the instructions to the right for proper assembly of the fiber optic lines.
# If installing the PCM3.1 CAM, the aftermarket camera plugs into the “CAM IN” cable of the
OPV.
12 Pin Molex wiring guide 12 Pin Molex connector image
Pin (1) Video out (high)
Pin (2) Video in (high)
Pin (4) Left audio (high)
Pin (3) Camera in (high)
Pin (5) Right audio (high)
Pin (6) Ground (Black wire)
Pin (7) Video out (low)
Pin (8) Video/CAM in (low)
Pin 10 Left/Right audio (low)
Pin (12) Constant +12volts In
Operation
Video in motion is automatic and doesn’t need any programming or
activation. Whenever an external video source is present, the radio will
always show an image.
To operate A/V input:
1. Press the source button.
2. Press the TV icon.
3. Once in the TV screen, tap above the preset icons in any blank
area to display the image.
08/20/14
NTV-DOC116
rB2