NavAtlas NS14A Operating instructions

INSTALLATION/OWNER'S MANUAL
NS14A/NS27A/NS35A

NS14A/NS27A/NS35A INSTALLATION
2
Preparation/Installation
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal. Consult a qualified technician for
instructions.
• Use extreme caution when drilling holes to avoid damaging fuel lines,
hydraulic lines or existing wiring.
• If additional wiring is required, we recommend that you run all wires prior to
mounting your speaker in place.
• Use the highest quality connectors for a reliable installation and to minimize
signal and power loss.
• Avoid running wires over, near, or through sharp edged surfaces. We suggest
you also use rubber grommets to protect any wires routed through metal.
Mounting and Installation
• Determine where the sound bar will be mounted. Ensure an area large enough
for the sound bar to mount evenly.
2mm LOCKING SEREWS FOR
ADJUSTABLE MOUNT ANCHORS

NS14A/NS27A/NS35A INSTALLATION
3
Preparation/Installation
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal. Consult a qualified technician for
instructions.
• Use extreme caution when drilling holes to avoid damaging fuel lines,
hydraulic lines or existing wiring.
• If additional wiring is required, we recommend that you run all wires prior to
mounting your speaker in place.
• Use the highest quality connectors for a reliable installation and to minimize
signal and power loss.
• Avoid running wires over, near, or through sharp edged surfaces. We suggest
you also use rubber grommets to protect any wires routed through metal.
Mounting and Installation
• Determine where the sound bar will be mounted. Ensure an area large enough
for the sound bar to mount evenly.
Part List
8x 5mm x 12mm Allen screws (Flush Mount Anchors) 2X Adjustable Brackets
8x 5mm x 15mm Allen screws (Adjustable Brackets) 2X Adjustable Anchors
2x 5mm x 15mm Allen screws (Adjustable Anchors) 2X 1.5” Bar Clamps
2x 2mm Allen screws (Adjustable Anchor Lock) 2X 1.75” Bar Clamps
2X Flush Mount Clamps 2X 2” Bar Clamps
4X Flush Mount Anchors 1 X Fuse Holder
Gaskets(Bar Mount & Flush Mount) 1 X Allen Tool
CLAMP GASKET *4
1.5’ BOTTOM
GASKETS *4
1.5’ TOP
GASKETS *2
1.75’ TOP
GASKETS *2
2’ TOP
GASKETS *2
1.75’ BOTTOM
GASKETS *4
2’ BOTTOM
GASKETS *4

NS14A/NS27A/NS35A INSTALLATION
4
When mounting the sound bar using the adjustable mount, please be sure to use
the appropriate size clamp for your bar size. Please use only the supplied screws
to fasten clamp
WARNING : When inserting screws please hand
tighten first before fastening and make sure the
screw is straight and not at an angle, this will
damage the screw thread of the mount.
When using the flush mount brackets, please be sure to use the supplied screws
when installing. Select the appropriate gaskets for your bar size, you can mix
and match the gaskets if the bar size is slightly smaller or bigger
PLEASE CUT CLAMP
GASTKET TO DESIRED
SIZE WHEN MOUNTING
SCREW THIS
SIDE FIRST WHEN MOUNTED ON BAR,
THE OVAL HOLE WILL GIVE
ROOM TO ADJUST WHEN
INSERTING SCREW
WARNING : WHEN INSERTING SCREWS,
MAKE SURE TO ALIGN SCREW WITH
ANCHORS
SLIDE SCREW ACHORS INTO SLOTS AND
POSITION UNDER SCREWS
INSTALL TOP SCREWS FIRST WHEN
MOUNTING
Preparation/Installation

NS14A/NS27A/NS35A INSTALLATION
5
Connection Descriptions
NOTE:
Be sure to follow specific instructions included with your product. The informa-
tion below should be used as a general guide only.
RED Power wire (12V+)
• Disconnect negative battery terminal before proceeding. Consult a qualified
technician for instructions if you are unsure.
• Plan wire routing before cutting any wires to length. Use a grommet when
running wires through the firewall or metal openings.
• Use extreme caution when drilling holes to avoid damaging fuel lines or
existing vehicle wiring.
• The +12V wire must be fused within 18” from the battery for protection of the
vehicle’s electrical system.
BLACK Ground wire (GND)
• Choose a clean unpainted section of metal or the vehicle chassis when
attaching the ground wire. Be sure to clean the area of any dirt or grease.
UNIVERSAL DIN CABLE (INCLUDED)
• BLUE LED wire (12V+) - Turns LED ON/OFF
• WHITE/RED RCA - Left/Right audio inputs
• GREY RCA - DIGITAL COAXIAL HI-DEF INPUT (DO NOT CONNECT TO ANALOG
AUDIO SOURCE)
*DIGITAL OUT NOT USED
UNIVERSAL CABLE
L
R
Digital
8 pin waterproof DIN connector
LED ON/OFF

NS14A/NS27A/NS35A INSTALLATION
6
SIGNAL INPUT
POWER
POWER LED
OUTPUT "DAISY CHAIN"
EXAMPLE OF DAISY CHAIN DIGITAL
CONFIGURATIONS FOR ANY VEHICLE
*OPTIONAL ACCESSORIES ARE D2Y AND D2D CABLES
(SOLD SEPARATELY)
10 Feet (10GA)
2 pin waterproof DIN connector
8 pin waterproof DIN connector
8 pin waterproof
DIN connector
Ground(-)
4 pin waterproof DIN connector
4 inch(18ga)
Ground(-)
10 Feet (12GA)
NS14A/27A/35A
8 pin waterproof DIN connector
A2A CABLE
BMA500M
Ground(-)
D2D CABLE
CONNECTING CABLE
CONNECTING CABLE
10 Feet (18GA) for soundbar
D2D CABLE
D2D CABLE
Y ADAPTER CABLE
NA1BT/NA2BT/NA30C
NA81MDVR (HEADUNITW/RC A OUT)
10 Feet (10GA)
2 pin waterproof DIN connector
8 pin waterproof DIN connector
10 Feet (18GA) for coundbar
8 pin waterproof
DIN connector
Ground(-)
NS14A/27A/35A
UNIVERSAL CABLE TO
AFTERMARKET AMPLIFIER
(BASS AMP, ECT...)
*DIGITAL OUT NOT
USED
L
R
Digita
LED ON /OFF
A2A CABLE
NA1BT/NA2BT/NA30C
NA81MDVR (HEADUNI TW/RCA OUT )
OUTPUT CAN CONNECT TO
ANY MODEL(NS14A/27A/35A,
NT650AT,BMA500)
WHEN USING AFTERMARKET AMPLIFIERS WITH SOUNDBARS, YOU MUST USE ANALOG
CABLES FOR DASIY CHAIN FUNCTION TO WORK, A2A CABLE(SOLD SEPARATELY) IS
REQUIRED FOR ANALOG AUDIO OUTPUT TO WORK IN THIS SETUP.
DAISY CHAIN SETUP
USING AFTERMARKET
AMPLIFIER
12V(+)
NT650AT
Soundbar
12V(+)
12V(+)
12V(+)
NT380W

NS14A/NS27A/NS35A INSTALLATION
7
DXP1000 / DXU1100 /
AFTERMARKET RADIO
10 Feet (10GA)
2 pin waterproof DIN connector
8 pin waterproof DIN connector
8 pin waterproof
DIN connector
Ground(-)
4 pin waterproof DIN connector
4 inch(18ga)
Ground(-)
10 Feet (12GA)
NS14A/27A/35A
8 pin waterproof DIN connector
A2A CABLE
2 pin waterproof DIN connector
BMA500M
Ground(-)
Ground(-)
A2A CABLE
X310WP
CONNECTING CABLE
CONNECTING CABLE
CONNECTING CABLE
line in L
line in R
Digital in
10 Feet (18GA) for soundbar
LED ON /OFF
UNIVERSAL CABLE
line in L
line in R
Digital in
LED ON /OFF
UNIVERSAL CABLE
X310WA
DAISY CHAIN SETUP USING ANALOG SIGNAL
WHEN USING ANALOG RCA FROM A RADIO, THE A2A CABLE(SOLD SEPARATELY) IS REQUIRED
FOR DAISY CHAIN FUNCTION TO WORK.
12V(+)
12V(+)
12V(+)
12V(+)
NT650AT
NT380W

NS14A/NS27A/NS35A INSTALLATION
8
Limited One Year Warranty
EXCHANGE ONLY ON FACTORY DEFECTS, PHYSICAL
DAMAGE IS NOT COVERED BY WARRANTY.

NS14A/NS27A/NS35A INSTALLATION
9
14"
Aluminum
3.5" 2pcs
0.75"
Aluminum
Rubber surround
Aluminum
EVA
0.5" 2pcs
HI-6dB/OCT
100W
27"
Aluminum
3.5" 6pcs
0.75"
Aluminum
Rubber surround
Aluminum
EVA
0.5” 4pcs
HI-6dB/OCT
200W
35"
Aluminum
3.5" 8pcs
0.75"
Aluminum
Rubber surround
Aluminum
EVA
0.5” 4pcs
HI-6dB/OCT
200W
size
type
Driver
Voice coil
Cone
Surround
Dust cap
Gasket
Tweeter
X-OVER
Power Handeling
Design and specifications subject to change without notice.
Specifications
NS14A/NS27A/NS35A

Support Line: 1-562-946-7471
9AM-5PM PST Monday-Friday
www.navatlas.com
All rights reserved.
NSA0418-V01
Printed in China