Navien KD One UHA-422SG/M User manual

DIGITAL COLOR LCD HANDS FREE
VIDEO PHONE
UHA-422SG/M
• Please carefully read this User’s Guide (in particular,
precautions for safety) before using a product and follow
instructions to use a product exactly.
• The company is not responsible for any safety accidents
caused by abnormal operation of the product.

Warning and important safeguards
Components
Installation
Product specications
Operation
Manager mode
Manager mode(Video memory equipped model)
Wiring diagram
Warranty
4
8
9
10
11
14
17
20
21
Contents



• To prevent injury, the following safety precaution should be observed during
installation, use and servicing of the unit.
Apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
Note : Change or modification not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This manual is based on the date as shown in the right and specification are
subject to change without notice for quality improvement
This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage”within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
CAUTION
RISK OF ELECTRIC SHOCKS
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE, REFER SERVING
TO QUALIFIED SERVICE PERSONNEL


For the customers
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communication.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning equipment on and o, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help



1. Read Instructions
All the safety and operating instructions should be read before the unit is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Follow Instructions
All operating instructions, maintenance and all warnings should be followed.
4. Cleaning
Turn o the power of unit before cleaning. Do not use liquid or aerosol cleaners.
Use a dry cloth for the body of unit.
5. Attachments
Do not use attachments not recommended by the unit product manufacturer,
as they may be hazardous or cause damage.
6. Heat and Moisture
Do not expose this unit direct sunlight and rain for reliable operation.
7. Installation
Do not install this unit on an unstable place (hot, cold, humid or excessive dust).
Use only with a mounting accessory recommended by the manufacturer or sold
with the unit.
Installing this unit should follow instructions of manufacturer and qualied service
personnel.
8. Ventilation
Slot and opening in the cabinet are provided for ventilation to ensure reliable
operation of the unit and to protect it from overheating.
These openings must not be blocked or covered. Never place your unit on a bed,
sofa, rug, or similar surface ;or on near a radiator or heat register.
This unit should not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided.
9. Power Sources
This unit should be operated only from the type of power source indicated on the
label. If you are not sure of the type of power supply to your home, consult your
appliance dealer or local power company.
To operate the unit by battery or other power source, consult the operating
instructions.


10. Grounding and Polarization
This unit may be equipped with either a polarized 2-wire AC line plug (a plug
having one blade wider than the other) or a 3-wire grounding type plug, a plug
having a third (grounding) pin. The 2-wire polarized plug will t into the power
outlet only one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug still fails to t, contact
your electrician to replace your outlet.
Do not defeat the safety purpose of the polarized plug.
11. Overloading
When using this product, do not overload the power outlets or extension cords
as this could cause re or electric shock.
12. Accessories
Do not place this unit on an unstable cart, stand, tripod, bracket, or table.
If the unit falls, it could cause injury or damage to the system.
13. Object and Liquids
Never push objects of any kind into this unit through the openings.
Never spill liquid of any kind on the unit.
14. Servicing
Do not attempt to service this unit yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to
qualied service personnel.
15. Power Line
The system should not be located near power lines or electric light
or power circuits.
16. Damage Requiring Service
Unplug this unit from the wall outlet and refer to servicing to a qualied
service technician if any of the following occur.
a. If the power supply cord or plug is damaged
b. If any liquid has been spilled into objects have fallen in the unit
c. If the unit has been exposed to rain or water
d. If the unit has been dropped or otherwise damaged
e. If the equipment exhibits a distinct change in performance
17. Replacement Part
When replacement parts are required, use replacement parts specied by the
manufacturer.



■
 Fixing Bracket
■
 Mounting Hardware & Cable
■ Main body
















 























■
 Standard height of video phone
1. After determining the mounting locations for
both the outside camera and inside monitor
2. At the selected monitor mounting location,
1,450mm is suggested from the bottom.
<Caution>
Install the monitor away from the heat,
moisture and direct sun rays.

■ Specications


DIV.
Power Source
Wiring
System Composition
Distance
Video
Memory
(Option)
Still Cut
Movie
LCD
Video
input
Temp.
Humidity
Size
Weight
LCD
Screen
Environmental
Circumstance
Dimensions
Mounting
Specications
AC 100~240(50/60Hz)
Doorphone : 4 wires in polarity
POWER, VOICE, VIDEO, GND
Interphone : 4 wires in polarity
VOICE, GND, POWER, CALL
Intercom : 2 wires in polarity
VOICE, GND
- 2 Doorphones + 4 Monitors
- Monitor + Optional interphone
- DOOR : TIV 0.5(28M), TIV 0.65(50M), TIV 0.8(70M)
(Up to the last videophone)
- INTERPHONE : TIV 0.5(20M)
256 Cuts
5f/s, 5sec, 32clips
4" Color TFT LCD
1Vp-p/75Ω, Composite
NTSC/PAL(Color)
0℃∼40℃
Less than 90% (Relative humidity)
202(W) * 142(H) * 32(D)mm
UHA-422SG : 585 g
UHA-422SGM : 605 g
Wall surface mounted



■ When using the Monitoring function
■ When a visitor pushes a Call Button
When a visitor pushes the Talk Button on the door-phone at the front door, the call is
transferred to the Videophone
Call signal is ringing on
the Videophone, while
Talk LED is ickering, and
the image of the visitor
appears on the screen.
(approximately 30 seconds)
When “Talk” Button is
pushed, the conversation
with the Visitors starts,
and Talk Button LED
Illuminates.
(max. 1 minute)
If you push the “Talk”
Button while talking with
the visitor or the time
limit of 1 minute is reached,
the screen goes blank and
the conversation ends.
If you push the
“Door Open” Button,
the relevant door
opens and the
conversation ends
‘DOOR#1’ or ‘DOOR#2’ appears at the top of the screen
‘DOOR#1’ or ‘DOOR#2’ appears at the top of the screen
If there’s no signal from the door phone camera, the ”No Signal” massage appears,
which means there is no video signal.
If you push the
“Monitoring” button,
pictures captured by the
door-phone at the front
door will appear on the
screen.
(maximum time: 1 minute)
If two door-phones are
installed, door-phone #2
can also be monitored by
pushing the “Monitoring”
Button one more time.
If you push the “Talk”
Button while using the
monitoring function,
talking is enabled
through the door-phone
that is currently installed.
If you push the
“Door Open” Button
during monitoring, the
relevant door opens
and monitoring ends.


■ Call signaling to another videophone
■ Intercommunication between videophones (when they are connected)
When a call signal comes
from another videophone,
Talk LED ickers and home
call melody rings.
(about 30 seconds)
When the “Talk” Button is
pushed, Talk LED is lit and
talking starts.
When the “Talk” button
is pushed during
communication or the talk
duration(up to 1minute),
the screen goes blank and
conversation ends.
‘INTERCOM’ appears at the top of the screen
‘INTERCOM’ appears at the top of the screen
When you push the “Talk” Button,
the Talk LED is illuminated and
you are in the state of connection.
At this point, you can give a call
signal to another videophone.
Regardless of whether the other
videophone line is busy or not,
if you push the Talk Button
or talking time expires
(max. 1 minute) , the screen goes
blank and talking ends.


■ Call signal to Interphone from video-phone
■ Call signal through Interphone
‘INTERPHONE’ appears at the top of the screen
‘INTERPHONE’ appears at the top of the screen
When you push and hold the
“Talk” Button for more than 1 second,
the Talk LED illuminates and you are
in the state of connection along with
call signaling to Interphone
When the receiver is picked up,
talking starts.(up to 1 minute)
Talk LED ickers and Interphone
call signal melody rings.
(1 time on the videophone)
If “Talk” Button is pushed, Talk LED
illuminates and conversation starts.



■ Menu setting function
How to control the call signal bell and talk volume
- You can control the call signal bell and talk volume using the switch located on the side
of the product.
Screen setting (Brightness)
- By pushing the “Up” or ‘Down” Button while you can see an image,
you can set the Brightness.
Status is indicated at the center of the bottom
- About 10 seconds after you have adjusted screen brightness(0~8, up to 9 phases)
with the “UP” or “DOWN” buttons, setting is complete and the indication disappears
from the screen.


Manager mode is the product setting mode that allows a installer to congure the device
environment(setting door-phone number and the type of door-phone camera) needed for operation.
*Manager mode ends automatically and standby mode is on when about 1 minute passes without
button input.
• When you are in Manager mode, you will not receive any door-phone, extension or interphone call.
※The product must be turned o and on again to save and apply the conguration changed in
Manager mode .
※When power is OFF →ON in the middle of changing the conguration on Manager mode, the
modication may fail to be applied
To select MANAGER MENU
- Enter “MANAGER” mode by pressing and holding the Door Open button for more than 3 seconds
in a standby state after power is on.
[Initial screen after it is switched on ]
[MANAGER MODE SCREEN]
UHA-422SG/SGM
www.kdone.co.kr
[MANAGER]
CAMERA TYPE
EXIT
CAMERA NUM


Setting CAMERA NUM (setting the number of door-phones in line with the videophone)
*This is the mode that allows you to set the number of door-phones in line with the videophone.
*Set up as Door-phone 1 by default.
- Select [CAMERA NUM] from the [MANAGER] MENU using the “UP” and “DOWN” buttons .
If you push the “TALK” button, [CAMERA NUM] appears, which indicates the current setup.
- Select the number of door-phones to be connected with videophone using the “UP” and
“DOWN” buttons at the bottom, and then push the ‘TALK’ button.
- If you push the “TALK” button after completing the settings, the [MANAGER] MENU screen will
appear again.
Setting CAMERA TYPE (setting the type of the door-phone camera)
*This is a mode that allows you to set the type of the door-phone camera to be connected with
the videophone.
*Set up as PAL by default.
- Select [CAMERA TYPE] from [MANAGER] MENU using the “UP” and “DOWN” buttons, and then
if you push the “TALK” button, [CAMERA TYPE] menu appears, which indicates current setup
- Select the type of the door-phone camera to be connected with the videophone using the
“UP” and “DOWN” buttons at the bottom and then push the ‘TALK’ button
If you push the “TALK” button after the completion of settings, the [MANAGER] MENU screen
appears again.
The changed conguration will be applied only after power is OFF/ ON one time.
※Caution: The camera must be connected that matches the conguration setup.
If you fail to do this, (e.g., connecting PAL camera while set up as NTSC) the screen image
may not appear correctly. Then, the screen is returned to the normal state when the power is
OFF →ON
[CAMERA NUM]
1 CAMERA
2 CAMERA
[CAMERA TYPE]
PAL
NTSC


Storing images of a visitor
* Storing, identifying and deleting images of visitors.
Storing images
- Storing of images is done automatically during call signaling to the door-phone, depending
on how the user has set up STILL/VIDEO storing in the user menu.
- If there’s no storage space, the oldest image will be deleted so that a new image can be
stored . (VIDEO : 5sec 32cut (5frames/1sec), STILL:256cut)
Playing images
- If VMM module is installed and there are stored images, push the ‘UP’ key on the right and
enter ‘PLAY’ mode. By pushing the ‘UP’ and ‘DOWN’ keys, the stored images can be
played in order.
- If VMM module is not installed, an Error sound may occur when you push the ‘UP’ and
‘DOWN’ keys on the right.
- If VMM module is installed and there’s no stored image, “NO Image” appears.
- If image storage type is set up as STILL, only STILL images are stored and played; if set up
as VIDEO, only video images are stored and played.
- If you push TALK button on an image playing screen or about 10 minutes passes, playing
ends automatically.
User menu (VMM setting menu)
- You can enter the User menu, by pushing the DOWN button while stanby.
- User menu is set up in association with VMM, so if VMM is not installed an ERROR sound
may occur when you push the DOWN button while in standby
- User menu ends automatically if about 30 seconds passes without pushing a button.
- While you are in User menu, call signaling to door-phone or extensions.
EXIT : menu closing
TIME : VMM time setting (for indication of storage time during playing of images)
SAVE : STILL/VIDEO
DELETE : deleting all the images and videos
※While you are in User menu, call signaling from other videophones or door-phone so only
when the connected videophones are all in standby, it is possible.
※When power is OFF →ON during setting data at User menu, the set data value may fail to
be applied.
※VMM : Video Memory Module



■ Additional functions (Video memory equipped model)
Setting the year
- When the “DOWN” button (on the right) is pushed from the standby screen, the User menu
screen appears.
- If you select “TALK” using the “UP” and “DOWN” buttons (on the right) on the Menu screen
and push the “TALK” button, YEAR, MONTH, DATE, HOUR and MINUTE appears.
- You can set the year using the “UP” and “DOWN” buttons, and if you push the “TALK” button,
you will move to Setting the month.
Setting the month
- Year setting is followed by Month setting.
- You can set the month using the “UP” and “DOWN” buttons, and if you push the “TALK” button,
you move to Setting the date.
Setting the date
- Month setting is followed by date setting.
- You can set the date using the “UP” and “DOWN” buttons, and if you push the “TALK” button,
you move to Setting the time.
Setting the hour
- Date setting is followed by time setting.
- You can set the hour using the “UP” and “DOWN” buttons, and if you push the “TALK” button,
you move to Setting the minute.
Setting the minute
- Hour setting is followed by minute setting.
- You can set the minute using the “UP” and “DOWN” buttons, and if you push the “TALK”
button, setup is complete and the data are stored.
Ending setup
- When minute setting is complete, the User menu screen appears again.
※If time set mode ends without completion of minute setting, the data being set up may
not be stored.
[USER MENU]
TIME
SAVE
DELETE
EXIT
[TIME SET]
: YEAR
: MONTH
: DATE
: HOUR
: MINUTE
00
00
00
00
00


■ User menu (Video memory equipped model)
* Video storage type setup mode
- If you push “DOWN” (on the right) button from the standby screen, the User
menu screen appears.
- Select “SAVE” on the menu screen pressing the “UP” and “DOWN” buttons on
the right, and push “TALK”
- The present storage type appears under selection.
- Select either VIDEO or STILL as storage type using “UP” or “DOWN”
(VIDEO : video(5 seconds) storage / STILL : still image storage)
- If you push the “TALK” button, the User menu appears again
- If you push the “DOWN” button on the standby screen, the User menu screen
appears
- Select “DELETE” on the menu screen using the “UP” and “DOWN” buttons,
and push “TALK”
- Select either YES or NO using the “UP” and “DOWN” buttons and push “TALK”
(YES : delete all images / NO : Do not delete images)
- User menu screen appears again after the operation is completed.
[SAVE]
STILL
VIDEO
[ALL DELETE?]
NO
YES



■ Doorphone Wiring
■ Interphone Wiring
 











If UTP CABLE[CAT.5] is used, use 5 lines for GND line
 











If UTP CABLE[CAT.5] is used, use 5 lines for GND line
Note :
Arbitrarily installed additional monitors may lower the quality of video and
voice transmission.