NCCO GoDEX T10 User manual

Parts Included
• Label rewinder
• Power adapter (24V)
• 1.5" core adapters
(optional)
• 3" core adapters
(optional)
• Manufacturer User Guide
• Quick Start Guide
NC DCG 09 002 (4/21)
DateCodeGenie®Label Rewinder Quick Start Guide
model GoDEX T10
Power Switch
Rewinding Switch
(Rewinding
Direction Switch)
Blue Label Press Bar
(Paper Press Bar)
Core Adapter Slots (3)
Paper Clip Holes x2
Lock Ring Knob (Paper
Stop plate Lock Ring)
Back Label Stop Plate
(Paper Stop Plate Left)
Label Rewinding Shaft
(Label Rewinding Shaft)
Front Label Stop Plate
(Paper Stop Plate Right)
Paper Clip

4. Wrap labels around the blue label press bar and
over the rewinding shaft in an “S” pattern when
labels feed from left or in a “Z” pattern when labels
feed from right.
2. Plug power adapter into rewinder and working
outlet. Do not turn on. Press the feed button of
printer to extend labels 10-14 inches.
Setup
1. Place label rewinder parallel to printer with 5 inch
minimum distance. Confirm printer to rewind and
label rewinding shaft are in a straight line.
3. Turn the lock ring knob counterclockwise to
remove and slide off front label stop plate. Pull
paper clip from end of label rewinding shaft to
remove. Set both aside.
5. Secure labels to label rewinding shaft with
cardboard core or paper clip option.
A. Cardboard Core Option
• Slide cardboard core on label rewinding shaft verifying
tight fit. Use core adapters, if needed. Use a piece of
tape or remove the first label and use to affix labels to
cardboard core.
B. Paper Clip Option
• Extend labels 1" over label rewinding shaft, pinch to
hold label in place. Line up paper clip with grooves
on end of label rewinding shaft. Slide paper clip over
labels and pinch slightly to press paper clip into 2 holes
on back label stop plate.
A. B.

9. Toggle power switch to " ", turning off power,
and cut labels near printer. Turn the lock ring knob
counterclockwise and remove. Slide the front label
stop plate to remove.
10. Slide label roll with cardboard core off label
rewinding shaft. Pull paper clip and remove to slide
off label roll, if using paper clip.
7. Toggle the rewinding switch to "Outside" (wind
labels facing outward) and the power switch to
" - " to power on, cycle through colored lights to
display pink.
6. Slide the front label stop plate on label rewinding
shaft leaving 1 mm space between the cardboard core/
edge of labels and the front label stop plate. Slide and
push the lock ring knob on the label rewinding shaft
and turn clockwise to lock front label stop plate in place.
8. Gently push the blue label press bar toward the
printer to start label rewinder. Label rewinder
automatically stops when labels are wound tight.
Move printer for labels to lay flat, if needed.

NC DCG 09 002 (4/21)
Training Resources
Have a DateCodeGenie question?
Find the answer in our knowledge base.
datecodegenie.com/support
Log into your portal at datecodegenie.com and access
all training tools from the Support tab. See videos,
knowledge base and more.
Contact & Support
North America
Technical Support
800.774.0478 x 1
[e-mail]
International
Technical Support
00 44 (0)1283 527299 x 4
[e-mail]
To learn more about NCCO and view a full list of our
products, visit us at ncco.com.
Looking for warranty information on your product? Limited-
warranty information for DateCodeGenie products and third-
party warranty information for accessories are all available to
view and download at: support.datecodegenie.com/warranty
Customer Service
800.328.6508
[e-mail]
Customer Service
00 44 (0)1283 527977 option 4
[e-mail]