NCR 1668-K015 Manual

Kit Instructions
Radial Arm Mount
1668-K015, K034
Issue B

ii
The product described in this document is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation. Product names mentioned in this publication may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is
permitted under the terms and conditions of an agreement you have with NCR, NCR's copyright notice
must be included.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software,
and firmware become available. NCR, therefore, reserves the right to change specifications without prior
notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the
world. In some instances, photographs are of equipment prototypes. Therefore, before using this document,
consult with your NCR representative or NCR office for information that is applicable and current.
Copyright © 2022
By NCR Corporation
Global Headquarters
864 Spring St NW
Atlanta, GA 30308
U.S.A.
All Rights Reserved

iii
Table of Contents
Radial Arm Mount
Introduction 1
Installation Procedure 3
Counterbalancing the Arm 12

iv
Revision Record
Issue Date Remarks
AApr 2022 First Issue
BMay 2022 Added 1668-K034

Radial Arm Mount
Introduction
The Radial Arm Mount permits a display to be mounted on a wall or a tabletop. It is
equipped with a 75 mm and 100 mm VESAadapter plate.
There are two Radial Arm Mount kits available.
Kit Number Part Number Display Weight Capacity
1668-K015 497-0486483 supports a 3.4 to 11.3 kg (7.5 to 25.0 lbs) display
1668-K034 497-0526229 supports a 0.9 to 5.9 kg (2.0 to 13.0 lbs) display

2 Radial Arm Mount
The Radial Arm Mount allows for easy vertical and horizontal repositioning of the
display.

Radial Arm Mount 3
Installation Procedure
1. Install the Mount on a tabletop or on a wall. There are six possible configurations.
Desk Edge
a. Assemble the Mount Column, Base Plate, and Large “L”Bracket using the 3/8-16
x 1” Flat Socket Cap Screw and 3/8-16 Nylon Stop Nut.
b. Install the Small “L”Bracket on the assembly using the 3/8-16 X 1/2” BHSCS.

4 Radial Arm Mount
c. Position the assembled Mount on the tabletop edge and secure it with the
Rectangular Spacer and 1/2-13 x 3” Socket Set Screw.
Thru-Desk – The Mount can be bolted through a tabletop with or without the Base
Plate.
a. Drill a 3/8” hole through the tabletop.
b. Install the Mount Column, with or without the Base Plate, as shown.

Radial Arm Mount 5
Grommet – The Mount can be installed through a 2.5” or larger Grommet Hole.
a. Assemble the Mount Column, Base Plate, and Large “L”Bracket using the 3/8-16
x 1” Flat Socket Cap Screw and 3/8-16 Nylon Stop Nut.
b. Position the assembled mount through the Grommet Hole then install the Small
“L”Bracket on the assembly using the 3/8-16 X 1/2” BHSCS.
c. Secure the Mount with the Rectangular Spacer and 1/2”-13 x 3” Socket Set
Screw.

6 Radial Arm Mount
Side Bolt
a. Assemble the Mount Column, Base Plate, and Large “L”Bracket using the 3/8-16
x 1” Flat Socket Cap Screw and 3/8-16 Nylon Stop Nut.
b. Install the assembled Mount as shown using two (2) screws. Use hardware
appropriate for the surface being mounted on.
Wall
a. Install the Large “L” Bracket on the wall in the orientation show (2 screws). Use
hardware appropriate for the surface being mounted on.