NEC PlasmaSync PX-50XM3A User manual

www.necvisualsystems.com 50XM3 Page 1 of 11
NEC Solutions (America), Inc.
VisualSystems
50XM3 Installation Guide
50” Plasma Display v1.0
Contents
Product Description and Notes Page 1
Ventilation Requirements Page 2
Display Dimensions
Front,Top&Bottom Page 3
Rear, Left & Right Side Page 4
Display Dimensions w/Optional Speakers and Stand Page 5
Dimensions w/Optional Flat Wall Mount Page 6
Dimensions w/Optional Tilt Wall Mount Page 7
Dimensions w/Optional Ceiling Mount Page 8
PortraitMode Page 9
Connections Page 10
Control Codes Page 11
ProductDescription
Type: Plasma Display Screen Surface: Anti-Reflective
Resolution: 1365x768 Dimensions: 48.1”(W) x 29.0”(H) x 3.8”(D)
Aspect Ratio: 16:9 Weight: 96.6 lbs
Color Correction: NEC CCF (Capsulated Color Filter, in panel)
and AccuCrimson (in front filter)
Notes
 This document is intended to be used as a reference guide to supply useful information for a design or installation. It is not
intended to be a step-by step procedure for installation.
 Any ceilings or walls must be strong enough to support the display and the installation must be in accordance with any local
building codes. All mounts should make secure contact to wood studs.
 4:3 sources can be displayed on the 16:9 screen in either normal aspect ratio with bars on the left or right, or stretched
horizontally to fill the screen using the menus (see “Aspect Modes” in menus and user manual).
 Distances are in inches, for millimeters multiply by 25.4.
 Distances may vary ±5%.
MaximumTiltAngles
Below are the maximum angles that the display can be tilted in both landscape and portrait mode
Landscape 30°
Portrait 10°
Max Tilt

www.necvisualsystems.com 50XM3 Page 2 of 11
Ventilation Requirements
Dimensions below are minimum required for proper ventilation.
NOTE: The ventilation space should not be covered or closed off at the front of the opening. If for some reason the
opening needs to be covered, other means of ventilation will need to be incorporated into the design. Contact NEC for
design review and recommendations.
WALL
WALL
WALL
2"
2"
2"
2"
2"

www.necvisualsystems.com 50XM3 Page 3 of 11
Display dimensions
Power Button
Filter Surface
28.98
48.11
43.54 (Screen Area)
24.49 (Screen Area)
Speaker Terminal
Control Buttons
LED & IR
0.217
IR15.20
0.79
0.79
0.79
0.79
0.79
2.46 1.46
4.92
18.11 5.94
44.33
25.43
AC Inlet
20.55
50.00

www.necvisualsystems.com 50XM3 Page 4 of 11
Display dimensions (cont.)
Power Button
12°
20.87
3.78
3.78
for PC option
4-M4*10 MAX for mount option
8-M4*14 MAX
for speaker option
4.96 2.56 2.56 4.96
13.8813.960.59
0.91
0.216
48.11
1.50 2.28
1.59
0.66
0.405
0.205
25.75
28.98 21.693.64
0.217
0.469
3.90 4.02
10.28 7.91
17.52
4.08
4.21
1.30
1.93
3.07
5.89
7.15
8.25
9.51
10.22
10.93
11.63
12.34
13.13
13.68
14.27
14.86
15.49
16.16
16.89
9.849.84

www.necvisualsystems.com 50XM3 Page 5 of 11
Dimensions with optional speakers and stand
(Screen Area)
(Screen Area)
28.98
48.11
43.54
24.49
28.98
50.00
3.78
2.80
31.77
32.05
55.24
6.72
15.75

www.necvisualsystems.com 50XM3 Page 6 of 11
Dimensions with optional Flat Wall Mount Kit (FWMK)
Note: The mount holes are 1.14” higher on the 50XM3 than on the 50MP2(PX-50XM2)
due to a higher center of gravity. (mount pattern is the same)
16.0 4.0
4.0
24.012.0 12.1
11.15.912.0
2.5 3.8

www.necvisualsystems.com 50XM3 Page 7 of 11
Dimensions with optional Tilt Wall Mount Kit (TWMK)
Note: The mount holes are 1.14” higher on the 50XM3 than on the 50MP2(PX-50XM2)
due to a higher center of gravity. (mount pattern is the same)
16.0
4.0 4.0
24.012.1 12.0
11.15.912.0
5.0 3.8
12.9
Depth at 15° Tilt

www.necvisualsystems.com 50XM3 Page 8 of 11
Dimensions with optional Ceiling Mount Kit (CMK)
Note: The mount holes are 1.14” higher on the 50XM3 than on the 50MP2(PX-50XM2)
due to a higher center of gravity. (mount pattern is the same)
0.23
24.3 23.8
8.0
Tilt Range: 0° - 15°
12.0
Tilt 15°
Tilt 0°
16.016.2 15.9
2.5
1.5
29.015.2

www.necvisualsystems.com 50XM3 Page 9 of 11
Portrait Mode
Rotating the Display
The display must be rotated clockwise so the input panel is at the bottom and vents are at the top.
Rotating the display counter-clockwise will not allow the unit to cool properly and will void the warranty.
Rotating Source Content
Note: The display is not capable of rotating any source content.
PC
Pivot® software from Portrait Displays, Inc. (www.portrait.com) allows you to rotate the Windows operating system 90 degrees. This
software installs in Windows on the PC and allows you to select landscape or rotate 90 degrees to portrait mode. Everything
running in the Windows environment is also rotated.
Note: All displays connected to the PC will have to support rotating to portrait mode.
NTSC Video
NTSC Video has to be brought into a PC with the appropriate hardware and software, and sent back out through the PC graphics
output. The method to rotate the video would then be the same as above and done within the PC Windows environment.
Inputs
Vents
Clockwise
Power
Rotate

www.necvisualsystems.com 50XM3 Page 10 of 11
Connections
VIDEO
(IN/OUT) VIDEO 1
VIDEO 3
VIDEO 2
AUDIO 1
R L
YCb/PbCr/Pr
DVD 1/HD 1 AUDIO 2
R
L
AUDIO 3
R L
Cr/Pr Y Cb/Pb HD VD
RGB 1
(IN/OUT)
RGB 3
DVI
OUTIN
REMOTE
External Control
LOCATED AT
BOTTOM OF DISPLAY
POWER
EXT. SPEAKERS
(MONO) (MONO)
R/ G/ B/
(MONO)
(Digital RGB)
RGB 2/DVD 2/HD 2