NEC NP600CM Guide

ISSUED: 08-05-08 SHEET #: 056-9008-6 06-28-10
Visit the Peerless Web Site at www.peerlessmounts.com
1 of 10
For customer care call 1-800-865-2112 or 708-865-8870.
Installation and Assembly Manual:
Custom Ceiling Mount for NEC NP300, NP310, NP400, NP410,
NP410W, NP500, NP500W, NP500WS, NP510, NP510W, NP510WS,
NP600, NP600S, NP610 and NP610S Projectors
Maximum UL Load Capacity: 50 lb (22.7 kg)
Model: NP600CM
Features:
• ImageLockTM alignment prevents picture sag or drift
• Wrench access slot for easier flush mount installations
• Exclusive aluminum track quick release
NEC Display Solutions of America, Inc.
This product is intended for use with UL
Listed products and must be installed by a
qualified professional installer.
©
UL
USC

ISSUED: 08-05-08 SHEET #: 056-9008-6 06-28-10
Visit the Peerless Web Site at www.peerlessmounts.com
2 of 10
For customer care call 1-800-865-2112 or 708-865-8870.
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Extension Columns / Ceiling Plate ...................................................................................................................4
Installation to Wood Joist Ceilings..........................................................................................................................................5
Installation to Concrete Ceilings.............................................................................................................................................6
Installation to Threaded Rods.................................................................................................................................................7
Attaching Adapter Plate to Projector.......................................................................................................................................8
Attaching Adapter Plate to Projector Mount............................................................................................................................9
Projector Alignment ..............................................................................................................................................................10
Tools Needed for Assembly
•stud finder ("edge to edge" stud finder is recommended)
•phillips screwdriver
•drill
•1/4" bit for concrete surface
NOTE: Read entire instruction sheet before you start installation and assembly.
•5/32" bit for wood studs
•level
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer care at 1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
• Never exceed the Maximum UL Load Capacity. See page 1.
• If mounting to wood joist ceilings, make sure that mounting screws are anchored into the center of the joist. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed and intended to be mounted to the following supporting surfaces checked below with
the hardware included in this product as specified in the installation sheet. To mount this product to an alternative
supporting surface, contact Peerless customer care at 1 800 865-2112.
• This product was designed to be installed on the following ceiling construction only;
CEILING CONSTRUCTION ADDITIONAL HARDWARE REQUIRED
x Wood Stud None
xWood Joist None
xSolid Concrete None
Cinder Block Contact Customer Service (Not Evaluated by UL)
Metal Stud Do not attach except with Peerless accessory kit for metal studs;
Contact Customer Service for Peerless accessory kit for metal studs.
(Not Evaluated by UL)
Brick Contact Customer Service (Not Evaluated by UL)
Other or unsure? Contact Customer Service (Not Evaluated by UL)
WARNING

ISSUED: 08-05-08 SHEET #: 056-9008-6 06-28-10
Visit the Peerless Web Site at www.peerlessmounts.com
3 of 10
For customer care call 1-800-865-2112 or 708-865-8870.
Description Qty. Part #
A
projector mount assembly 1 055-2968
B4 mm security allen wrench 1 560-9646
C#10-32 x 3/8" serrated washer head socket pin screw 2 520-2151
D#10-32 x 1/4" socket pin screw 1 520-2196
Eflat washer 2 540-1078
F#14 x 2.5 phillips hex head wood screw 2 5S1-015-C04
Gconcrete anchor 2 590-0097
A
A
adapter plate 1 055-2869
BB M4 x 16 mm serrated socket pin screw 3 510-2087
CC retaining spacer 3 590-2009
DD 2 mm allen wrench 1 560-1097
EE connection block 1 580-4065
Parts List
NOTE: Actual parts may appear slightly different than illustrated.
Before you start check the parts list to insure all of the parts shown are included.
C
A
D
G
E
FCC
BB
AA
B
DD
EE

ISSUED: 08-05-08 SHEET #: 056-9008-6 06-28-10
Visit the Peerless Web Site at www.peerlessmounts.com
4 of 10
For customer care call 1-800-865-2112 or 708-865-8870.
Installation to Extension Column / Ceiling Plate
A
1 1/2" EXTENSION COLUMN
(SOLD SEPARATELY)
(UL LISTED EXT OR AEC SERIES)
ARROW
INDICATES FRONT
OF MOUNT
fig. 1.1
fig. 1.2
SWIVEL STOP
SCREW
CMJ 455
(SOLD SEPARATELY)
NOTE: Refer to accompanying instructions with ceiling plates (sold separately) for installing these models to
ceiling.
Screw projector mount assembly (A) onto extension column as shown in figure 1.1. Tighten swivel stop screw
against extension column, flush mount tube or reducer using 4 mm security allen wrench (B) as shown in figure
1.2.
NOTE: Swivel stop screw is used to jam against threads of extension column, flush mount tube or reducer to
prevent any excess movement of projector mount assembly (A). Do not overtighten screw; overtightening screw
will damage threads making it difficult to separate products.
Skip to step 5.
1

ISSUED: 08-05-08 SHEET #: 056-9008-6 06-28-10
Visit the Peerless Web Site at www.peerlessmounts.com
5 of 10
For customer care call 1-800-865-2112 or 708-865-8870.
Place projector mount assembly (A) on ceiling as a template and mark the center of the two mounting holes.
Make sure that the mounting holes are in the center of the wood joist. Drill two 5/32" (4 mm) dia. holes to a
minimum depth of 2.5" (64 mm). Attach projector mount assembly (A) with two #14 x 2.5" wood screws (F) and
two flat washers (E) as shown in figure 2.1 or figure 2.2 depending on joist orientation.
NOTE: Mounting slots on projector mount assembly allow for 30° (±15°) of swivel adjustment before fully securing
wood screws.
Tighten wood screws (F) using 3/8" (10 mm) socket wrench or phillips screwdriver until projector mount assembly
(A) is firmly attached.
Skip to step 5.
Installation To Wood Joist Ceilings
FRONT OF
MOUNT
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that projector mount assembly is firmly attached, but do not overtighten. Overtightening
can damage the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder
is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-
ers are responsible to provide hardware for other types of mounting situations (Not Evaluated by UL).
WARNING
ARROW ON TOP OF
PROJECTOR MOUNT
ASSEMBLY INDICATES
FRONT OF MOUNT
FF
A
WOOD JOIST
EE
WOOD JOIST
A
fig. 2.1 fig. 2.2
2

ISSUED: 08-05-08 SHEET #: 056-9008-6 06-28-10
Visit the Peerless Web Site at www.peerlessmounts.com
6 of 10
For customer care call 1-800-865-2112 or 708-865-8870.
Installation to Concrete Ceilings
Place projector mount assembly (A) on ceiling as a
template and mark the center of the two mounting
holes. Drill two 1/4" (6 mm) dia. holes to a minimum
depth of 2.5" (64 mm). Attach projector mount assembly
(A) using two Alligator®concrete anchors (G), two flat
washers (E), and two #14 x 2.5" wood screws (F) as
shown in figure 3.1.
NOTE: Mounting slots on projector mount assembly
allow for 30° (±15°) of swivel adjustment before fully
securing wood screws.
Tighten wood screws (F) using 3/8" (10 mm) socket
wrench or phillips screwdriver until projector mount
assembly (A) is firmly attached.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
WARNING
CUTAWAY VIEW
INCORRECT
concrete
plaster/
drywall
CORRECT
concrete
plaster/
drywall
A
A
• Always attach concrete anchors directly to load-bearing
concrete.
• Never attach concrete anchors to concrete covered with
plaster, drywall, or other finishing material. If mounting
to concrete surfaces covered with a finishing surface is
unavoidable (not evaluated by UL), the finishing surface
must be counterbored as shown below. Be sure concrete
anchors do not pull away from concrete when tightening
screws. If plaster/drywall is thicker than 5/8", custom fas-
teners must be supplied by installer (not evaluated by UL).
• Tighten wood screws firmly, but do not overtighten.
Overtightening can damage the screws, greatly reducing
their holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
WARNING
G
F
E
A
CONCRETE CEILING
ARROW ON TOP OF
PROJECTOR MOUNT
ASSEMBLY INDICATES
FRONT OF MOUNT
1
3
Drill hole and insert anchor
CONCRETE
CEILING
F
F
2A
G
G
G
Place mount over anchor and secure with screw and
washer
After repeating step one tighten all fasteners
E
E
3
fig. 3.1

ISSUED: 08-05-08 SHEET #: 056-9008-6 06-28-10
Visit the Peerless Web Site at www.peerlessmounts.com
7 of 10
For customer care call 1-800-865-2112 or 708-865-8870.
Thread two 1/4-20 hex thin nylon-insert locknuts (not included) on two 1/4-20 threaded rods (not included) to the
desired height of projector mount assembly. Attach projector mount assembly (A) to the two 1/4-20 threaded rods
using two 1/4-20 hex thin nylon-insert locknuts as shown in figure 4.1 or figure 4.2.
Installation to Threaded Rod
(Not evaluated by UL - Professional installation only)
1/4-20 THREADED ROD
(NOT INCLUDED)
A
1/4-20 HEX THIN
NYLON-INSERT
LOCKNUT
(NOT INCLUDED)
1/4-20 HEX THIN
NYLON-INSERT
LOCKNUT
(NOT INCLUDED)
ARROW
INDICATES
FRONT OF
MOUNT
1/4-20 THREADED ROD
(NOT INCLUDED)
A
1/4-20 HEX THIN
NYLON-INSERT
LOCKNUT
(NOT INCLUDED)
1/4-20 HEX THIN
NYLON-INSERT
LOCKNUT
(NOT INCLUDED)
ARROW
INDICATES
FRONT OF
MOUNT
fig. 4.1 fig. 4.2
4

ISSUED: 08-05-08 SHEET #: 056-9008-6 06-28-10
Visit the Peerless Web Site at www.peerlessmounts.com
8 of 10
For customer care call 1-800-865-2112 or 708-865-8870.
Align shoulder on connection block (EE) oppo-
site notch in adapter plate (AA). Attach adapter
plate to connection block (EE) from projector
mount
assembly (A) using two #10-32 x 3/8" serrated
washer head socket pin screws (C) as shown
in figure 5.1. Tighten screws using 4 mm allen
wrench (B).
C
NOTCH INDICATES
FRONT OF PROJECTOR
SHOULDER
Attaching Adapter Plate to Projector
fig. 5.1
BB
Flip projector upside down and attach adapter plate (AA) using three serrated socket pin screws (BB) and
retaining spacers (CC) as shown below. Tighten using 4 mm allen wrench (B).
NOTE: Retaining spacers (CC) go between the projector and adapter plate (AA).
AA
CC
AA
EE
5
6

ISSUED: 08-05-08 SHEET #: 056-9008-6 06-28-10
Visit the Peerless Web Site at www.peerlessmounts.com
9 of 10
For customer care call 1-800-865-2112 or 708-865-8870.
Slide connection block (EE) with projector into projector mount assembly (A) as shown. Tighten captive screw to
secure projector to projector mount assembly (A).
IMPORTANT: For security installations, insert one #10-32 x 1/4" socket pin screw (D) through projector mount
assembly (A) and into connection block (EE) as shown in detail 1. Tighten screw using
4mm security allen wrench (B).
A
D
• Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely
handle placement of the screen.
WARNING
A
FRONT OF MOUNT
CAPTIVE SCREW
ARROW
INDICATES
FRONT OF
MOUNT
Attaching Adapter Plate to Projector Mount
DETAIL 1
EE
EE
7
7

ISSUED: 08-05-08 SHEET #: 056-9008-6 06-28-10
Visit the Peerless Web Site at www.peerlessmounts.com
10 of 10
For customer care call 1-800-865-2112 or 708-865-8870.
SCREW FOR YAW (SWIVEL) STOP
(REFER TO STEP 1, INSTALLATION
TO EXTENSION COLUMNS, FIG. 1.2)
KNOB FOR ROLL
ADJUSTMENT
KNOB FOR PITCH
ADJUSTMENT
BACK OF MOUNT
ARROW INDICATES
FRONT OF MOUNT
To adjust yaw (swivel) for wood stud, concrete ceiling, and threaded rod mounting applications: Loosen
wood screws (F) if flush mounted to wood joists (page 5) or concrete ceilings (page 6), or loosen locknuts on
threaded rods (page 7), until projector mount can be rotated. Rotate mount to desired position and retighten
screws or locknuts.
To adjust yaw (swivel) for extension column applications: Loosen screw on projector mount assembly (A)
indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw.
To adjust pitch (forward and backward tilt): Turn knob on back of mount as shown below. Pull knob out and
turn by hand for easy adjustment or insert #2 phillips screwdriver in end of knob and turn.
To adjust roll (side to side tilt): Turn knob on side of mount as shown below. Pull knob out and turn by hand for
easy adjustment or insert #2 phillips screwdriver in end of knob and turn.
A
To prevent tampering with the pitch and roll adjustments: Tighten the two tamper resistant security screws
on the projector mount assembly using 4 mm security allen wrench (B) to lock the pitch and roll adjustments as
shown below. Note: Tighten screws firmly, but do not overtighten. Overtightening can damage the mount.
• Do not adjust pitch or roll while tamper resistant security screws are fully engaged.
• Loosen the two tamper resistant security screws one complete turn before adjusting the projector mount assembly
or damage may occur.
CAUTION
SIDE VIEW
Projector Alignment
8-1
TO LOCK PITCH TIGHTEN
TAMPER RESISTANT
SECURITY SCREW
© 2009, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
8