Nemschoff Palisade 2.0 User manual

Tools Required
Parts Included
H- Seat Booth
H-L Seat Booth
H-R Seat Booth
Nemscho Palisade 2.0
2Seat Booth, 1Seat LSF and RSF Booth
Installation Instructions
How to assemble your 2 seat booth,
1 seat LSF and RSF booth.
Step 
Step 
H- Seat Booth
Utility KnifePower Drive
1.1 Feel for hole with nger, then carefully cut with sharp utility knife by
using approximate measurement given below.
1.2 Remove fabric from area around bracket mounting hole location, top
bracket mounting locations. Take care not to extend fabric cuts more than
¼ inch from hole center.
(This Step is supposed to be done in the factory but just in case
here is what needs to be done)
7-5/8”
7-5/8”
1-3/4”
1-3/4”
2.1 Repeat same for other hole mounting location.
Utility Knife
Utility Knife
Seat Booth (LSF)
Seat Booth (LSF)
Seat Booth (RSF)
Seat Booth (RSF) Table Assembly
Table Assembly
Table Assembly
Back Extension (2 Seat)
Back Extension (RSF)
Back Extension (LSF)
1Nemscho for Palisade 2.0 Assembly Instructions1BP8JN rev A

2Nemscho for Palisade 2.0 Assembly Instructions1BP8JN rev A
Step  Step 
3.1 Install the back tube by using 2 flat washers and 2 round head machine
screws (2” long).
3.2 Repeat the same for other side.
4.1 Attach the support center by using 4 flat washers and 4 round head
machine screws (0.625” Long).
4.2 Repeat the same for other side.
Step  Step 
5.1 Install the back extension assembly in between the seats and secure with 2
flat washers and 2 round head machine screws (2.5” long) at the top.
5.2 Then install the assembly by using 4 flat wahsers and 4 round head machine
screws (2” long) at the bottom.
6.1 Attach the Z-Bracket by using 4 screws as shown below.
Back Tube
Flat Washer
Round head
Machine Screw
Support Center
Round head
Machine Screw
Flat Washer
Flat
Washer
Round head
Machine Screw
Back Extension
Assembly
Flat
Washer
Round head
Machine Screw
Z-Bracket
Screw

3Nemscho for Palisade 2.0 Assembly Instructions1BP8JN rev A
Step  Step 
7.1 Insert set screw into the access panel.
7.2 By using 3 flat washers and 3 round head machine screws (0.5”
long), install the access panel as shown below.
8.1 Install the table assembly in between the 2 seat booth by using 6 flat
washers and 6 round head machine screws (0.625” long), (4 at the bottom
and 2 at the back) as shown below.
Round head
Machine Screw
Round head
Machine Screw
Round head
Machine Screw
Table Assembly
Flat
Washer
Flat
Washer
Flat Washer
Access Panel
Set Screw
Access
Panel
Step 
H-L Seat Booth
Step 
1.1 Feel for hole with nger, then carefully cut with sharp utility knife by
using approximate measurement given below.
1.2 Remove fabric from area around bracket mounting hole location, top
bracket mounting locations. Take care not to extend fabric cuts more than
¼ inch from hole center.
(This Step is supposed to be done in the factory but just in case
here is what needs to be done)
7-5/8”
1-3/4”
Utility Knife
2.1 Install the back tube by using 2 flat washers and 2 round head machine
screws (2” long) (2 at the bottom and 2 at the end of tube).
Flat Washer
Flat Washer
Round head
Machine Screw
Round head
Machine Screw
Back Tube

4Nemscho for Palisade 2.0 Assembly Instructions1BP8JN rev A
3.1 Attach the support back by using 4 flat washers and 4 round head
machine screws (0.625” Long).
Step 
Round head
Machine Screw
Flat Washer
Step 
4.1 Install the back extension by using 4 flat wahsers and 4 round head
machine screws (2” long).
Support Back
Step  Step 
5.1 Attach the Z-Bracket by using 4 screws as shown below. 6.1 Attach the L-Bracket on the access panel as shown below.
6.2 Insert set screw into the access panel
Z-Bracket
Screw
L-Bracket
Screw
Set Screw
Back Extension
Round head
Machine Screw Flat Washer

5Nemscho for Palisade 2.0 Assembly Instructions1BP8JN rev A
7.1 Install the access panel by using the L-Bracket screws, 1 flat washer
and 1 round head machine screw (0.5” long).
Step  Step 
Round head
Machine Screw
Access Panel
Screw
Flat Washer
8.1 Install the table assembly by using 6 flat washers and 6 round head
machine screws (0.625” long), (4 at the bottom and 2 at the back)
as shown below.
Round head
Machine Screw Round
head
Machine
Screw
Flat
Washer
Flat
Washer
Table Assembly
H-R Seat Booth
Step 
1.1 Feel for hole with nger, then carefully cut with sharp utility knife by
using approximate measurement given below.
1.2 Remove fabric from area around bracket mounting hole location, top
bracket mounting locations. Take care not to extend fabric cuts more than
¼ inch from hole center.
(This Step is supposed to be done in the factory but just in case
here is what needs to be done)
7-5/8”
1-3/4”
Utility Knife

6Nemscho for Palisade 2.0 Assembly Instructions1BP8JN rev A
Step 
Back Tube
3.1 Attach the support back by using 4 flat washers and 4 round head
machine screws (0.625” Long).
Step 
Round head
Machine Screw
Flat Washer
Support Back
Step 
4.1 Install the back extension by using 4 flat wahsers and 4 round head
machine screws (2” long).
Flat Washer Round head
Machine Screw
Back Extension
Step 
5.1 Attach the Z-Bracket by using 4 screws as shown below.
Z-Bracket
Screw
Flat Washer
Round head
Machine Screw
2.1 Install the back tube by using 2 flat washers and 2 round head machine
screws (2” long) (2 at the bottom and 2 at the end of tube).
Flat Washer Round head
Machine Screw

7Nemscho for Palisade 2.0 Assembly Instructions1BP8JN rev A
Step 
6.1 Attach the L-Bracket on the access panel as shown below.
6.2 Insert set screw into the access panel
Screw
L-Bracket
Set Screw
7.1 Install the access panel by using the L-Bracket screws, 1 flat washer
and 1 round head machine screw (0.5” long).
Step 
Round head
Machine Screw
Access Panel
Screw
Flat Washer
Step 
8.1 Install the table assembly by using 6 flat washers and 6 round head
machine screws (0.625” long), (4 at the bottom and 2 at the back)
as shown below.
Round head
Machine Screw
Round
head
Machine
Screw
Flat
Washer
Flat
Washer
Table Assembly