Ness S2 User manual

1
S2
Metal Waterproof Access Control Unit
Installation and User Manual
(Ness Part No. 101-082)

2
Introduction
Ness S2 is an advanced, waterproof (IP65 rated) proximity and PIN Access Contro er. S2 can support 2500 users
uti izing three access modes; Card on y - Card p us PIN - Card or PIN
S2 can operate in standa one mode, with its interna re ay activating when an authorized user is granted access or can
interface to 3
rd
party products via its 26 Bit Wiegand output
Installation
Dri a ho e in the wa to match the ocation of the
cab e at the rear of the S2 or mount a suitab e wa
mount junction box
Thread the cab e through cab e ho e and connect
re ated cab es. Take care to insu ate the unused
cab es to prevent shorting
Fix the back cover to the wa or distribution box
with screws and secure the contro er to the back
casing
Connection Diagram

3
Programming
0 - Resetting to Factory Defaults
To reset to factory defau ts, power off then press and ho d the * key whi e powering up. S2 wi beep twice and the
LED wi g ow orange. Re ease the * key and the S2 wi be ready for one of the fo owing options:
1) Presenting the “Add User Master Card” to S2’s Reader to add a new user
2) Presenting the “De ete User Master Card” to de ete a current user
3) Presenting a b ank EM card to rep ace an “Add User Master Card” or “De ete User Master Card”. In this
case the first b ank card presented wi become the new “Add User Master Card” and the second b ank
card presented wi become the new “De ete User Master Card”. The LED wi f ash Red confirming that S2
has been reset to factory defau ts and new Master Cards added. If the new Master Cards are not presented
within 10 seconds S2 wi resume User Operating Mode and the LED wi g ow steady Red
When resetting to factory defau ts the user's information is sti retained
1
-
Entering Programming Mo e
(Defau t Master Code = 888888
)
Press * then enter the Master Co e fo owed by # (e.g. * 888888 #)
S2 wi enter Program Mode, the LED wi f ash Green for one second and then g ow steady Red whi e S2 awaits
Program Option Commands. To Exit Program Mode press *. If no keys are pressed for 60 seconds S2 wi
automatica y exit Program Mode and resume Operation Mode
The following options can be accesse an programme in Program Mo e
2
-
Changing the
Master Co e
(Master Code must be 6 digits ong)
(Can on y be done in Master Programming Mode)
Press 0 - The LED wi g ow Orange. Enter a New Co e fo owed by # then re-enter the same New Co e fo owed
by # . The LED wi f ash Green if successfu
Press
0
New Co e
#
Confirm New Co e
#
Up to 2500 user cards can be added. The first two options are avai ab e in Program Mode on y and the third is a so
avai ab e in Operation Mode
3.1 A ing Car Users Automatically in Program Mo e (Not recommen e )
Press 1 - The LED wi g ow Orange. Present a blank car to the Reader. S2 wi automatica y assign the first card
as User Card 1. When successfu the LED wi f ash Green. Repeat this process for a new cards and then press #
This method is not recommended because S2 wi automatica y a ocate added cards to the next avai ab e
empty card s ot. This makes it difficu t to de ete a card as its a ocated card s ot (ID number) wi not be known
3
-
A ing Users
(Can on y be done in Master Programming Mode)
Press
1
Present Car 1
Present Car 2
Present Car 3
…
#

4
3.2 A ing Car Users Manually (Recommen e metho )
Press 1 - The LED wi g ow Orange. Enter the ID Number (Memory s ot number 1 -> 2500 of the card you wish to
add) fo owed by #. Present the new card to the Reader. When successfu the LED wi f ash Green. If more cards
are to be added repeat the process. Press # to end
Press 1
Enter ID
No.1 #
Present
Car 1
#
Enter ID
No.2
Present
Car 2
# …
S2 wi auto assign PIN “1234” (Factory Defau t) to programmed cards. If the system is set for ‘Card AND PIN’
for access you must go to “User Settings” and assign an individua PIN to each card
This is the recommended method of adding Card Users as the ID Number of a cards programmed wi be known
making it easy to se ect any individua card you may wish to de ete
3.3 A ing “PIN Only” Users (No car )
Press 1 - The LED wi g ow Orange. Enter the ID Number (Memory s ot number 1 -> 2500 of the User) fo owed by
#. Enter a PIN for that User. When successfu y added the LED wi f ash Green. Press # to end. If more Users are
to be added repeat the process for each User
Press
1
Enter ID No.1
#
Enter PIN 1
#
Enter I
D No. 2
Enter PIN 2
#
...
A PIN numbers must be 4 Digits of any number combination, however they must not be 1234
3.4 A ing Car Users Sequentially
Mu tip e Users can be added sequentia y as either a Card or Pin
Press
1
Present Car 1
to the Rea er
Enter ID
No.1
Present Car 2
to the Rea er
Enter ID
No. 2 …
Enter
PIN 3
#
Enter ID
No. 3
#
…
3.5 A ing Users with the “A User Master Car ”
User Cards can be added anytime without entering Program Mode by using the “Add User Master Card” that
comes with the unit (or card that you have programmed)
Present “A User Master Car ” to the Reader - The LED wi g ow Orange. Present the Car to be a e . When
successfu y added the LED wi f ash Green. Present any a itional car s to be a e in sequence. When
comp ete Present “A User Master Car ” again. The LED wi f ash Red
Present ‘A User Master
Car ’ to the rea er
Present each Car to be a e
to the rea er in sequence
Present ‘A User Master
Car ’ to the rea er to exit
If the card being added is a ready in the system S2 wi respond with 3 beeps

5
4
-
Deleting
Users
(Can on y be done in Master Programming Mode)
4.1 Deleting Users Automatically
Press 2 -The LED wi g ow Orange. Present each Car to be Delete to the reader in sequence. As each card is
successfu y de eted the LED wi then f ash Green. Press # to exit
Press 2
Present Car 1
to be elete
Present Car 2
to be elete
Present Car 3
to be elete …
#
4.2 Deleting Users Manually
If the card to be de eted is ost or unavai ab e the ID Number of the User (Memory S ot the User is programmed
into) must be used to identify the User
Press 2 - The LED wi g ow Orange. Enter the ID number of the User to be elete then press #. When
successfu y de eted the LED wi f ash Green. Repeat this process for any more Users to be de eted
Press 2
Enter ID
Number
of the
User to be elete
#
Enter
ID
Number
of the
next User to be elete … #
4.3 Deleting ALL users
Press 2 - The LED wi g ow Orange. Press 0000 fo owed by the # button. The LED wi then f ash Green confirming
that a Users have been de eted
Press
2
0000
#
4.4 Deleting Users using the “Delete User Master Car ”
Cards may be de eted anytime without entering Programming mode using the “De ete User Master Card” that
comes with the S2 (or other programmed card)
Present “Delete User Master Car ” to the Reader - The LED wi g ow Orange. Present the Car to be Delete .
When successfu y De eted the LED wi f ash Green. Present any a itional Car s to be Delete in sequence.
Present the “Delete User Master Car ” to the reader again to comp ete. The LED wi f ash Red
Present the ‘Delete User
Master Car ’ to the Rea er
Present each Car to be a e to
the Rea er in sequence
Pre
sent the ‘Delete User
Master Car ’ to the Rea er
If the card being de eted is not in the system the S2 wi respond with 3 beeps

6
6
–
Door
Access Control
Settings
(Can on y be done in Master Programming Mode)
Three programming options for Door Access Contro are provided; Card On y, Card AND PIN or Card OR PIN
6.1 Grant Access by Car Only
6.2 Grant Access by Car AND PIN
6.3 Grant Access by Car OR PIN (Factory Defau t )
7
–
Door
Relay Time Set
ting (U
nlock Time)
–
>
Default = 5 Secon s
(Can on y be done in Master Programming Mode)
This option sets the activation time of the Re ay when Access is granted by Card or PIN
Press
4
Enter Activation time (0
-
>
99 Secon s)
#
8
–
Door Open Detection Se
ttings
(Can on y be done in Master Programming Mode)
These options are used to Enab e / Disab e the “D_In” (Door Switch Input).
Press
60
#
Disables the Door Open Detection
Input
(Factory Defau t)
Press
61
#
Enables the Door Open Detection
Input
When enab ed:
If the door is opened norma y but not c osed within 1 minute the buzzer wi sound for 1 minute
If the door is forced open (opened by an unauthorized user) the buzzer and a arm output wi be activated
9
–
Security Mo e Settings
for
Invali Ac
cess Attempts
(Can on y be done in Master Programming Mode)
Three options are provided for programming Keypad Lockout / A arm Output in the event that mu tip e inva id
Access attempts are made. Programming any option wi override a previous settings
Pr
ess
70
#
Normal Status
(No Alarm Output or Keypa Lockout)
(Factory Defau t)
When enab ed, the number of keypad entries is unrestricted (no A arm Output or Keypad ockout regard ess of
the number of inva id code entries)
When enab ed, the Keypad wi ockout for 10 minutes if there are 10 successive inva id card presentations or 10
successive incorrect PIN numbers entered within a 10 minute period
Press
72
#
Alarm Output
Press
3
0
#
Press
3
1
#
Press
3
2
#
Press
71
#
Keypa Lockout

7
When enab ed, the S2 Buzzer wi sound and the A arm Output wi be activated if there are 10 successive inva id
Card presentations or 10 successive incorrect PIN numbers entered within a 10 minute period
10
–
Site
Co e
Setting
(for Wiegand Output
)
(Can on y be done in Master Programming Mode)
When a va id User Code is entered the Wiegand Output wi transmit the Site Code a ong with the 4 Digit PIN
number entered as the Wiegand Card Number
Examp e - If the PIN used is 8888 and the Site Code is 029 then the fu 8 digit, 26 Bit Wiegand number
transmitted on the Wiegand Output is 029 08888
The defau t Site Code is 029 however an a ternative Site Code may be programmed
Press
81
Enter Require Site Co e (0
-
>
255)
#
Site Code must be between 0 and 255
11
–
Se
tting the A ress of the Rea er
(Defau
t 0)
(Can on y be done in Master Programming Mode)
When using S2 with security equipment that supports addressab e readers such as Ness D8XD / 16XD Pane s,
Ness 6DA contro ers etc it may be necessary to set the address of the reader
When programmed to Address 0 (Defau t) the Wiegand Output uses standard 26 Bit Wiegand protoco .
When set to address 1, 2 or 3 the Wiegand Output appends Ness encrypted protoco s to S2’s address
0 - S2 Address 0 (Defau t)
1 - S2 Address 1
2 - S2 Address 2
3 - S2 Address 3
Pre
ss
82
Enter A ress (0
-
>
3)
#
(Factory Defau t is
0
-
St
andar
d 26 Bit Wiegand
output
)
12
–
Alarm Output Time
(Defau t 1 Minute)
(Can on y be done in Master Programming Mode)
This option sets the A arm Output Time (duration) of S2’s A arm Output
Press
9
Enter Alarm
Time in Minutes (1
-
>
3)
#
(Factory Defau t is
1
-
1 Minute)

8
USER
SETTINGS
(User Settings can be programmed by the User at any time without entering Program Mode)
Assigning a PIN to a CARD
If the system is programmed for access is to be granted with “Card and PIN” (Programming Option 32 set) a PIN
for each Card must be assigned using this option. (The Factory Defau t when cards are first programmed into
the system is PIN 1234)
Press *
Present the Car
to the Rea er
Enter Ol PIN
(Default 1234)
#
Enter
NEW PIN
#
Repeat the
NEW PIN
#
Assigning a PIN to a ID Number
This option a so assigns a PIN to a Card, but if the card is unavai ab e you can assign it to the User’s ID Number
(Memory s ot Number)
Press *
Enter the ID
Number the PIN
will be assigne to
#
Enter
Ol PIN
#
Enter
New PIN
#
Repeat the
NEW PIN
#
OPERATION
Unlocking the Door By Car OR PIN .
If the Door Access Contro Setting (Section 6) is programmed to “Card or PIN”, access wi be granted by
presenting a va id Card to the Reader or by entering a va id PIN
Either OR
If successfu , the LED wi f ash Green and the Re ay wi activate for the Un ock time
If unsuccessfu , the S2 wi sound 3 Beeps and the ike y cause wi be a non va id Card (unprogrammed or
incorrect y programmed) or incorrect PIN entry (refer to Programming Section 3, “Adding Users”)
If a Card is presented and the LED g ows steady S2 is waiting for a PIN to be entered. If this is not intended refer
to Programming Section 6 “Door Access Contro Settings” and se ect the correct Access Setting
Present Car to Rea er
Enter 4 Digit PIN followe by
#

9
Unlocking the Door By Car AND PIN
If Door Access Contro is set to “Card” (Section 6), access wi be granted by presenting a va id Card to the Reader.
The LED wi g ow RED upon the presentation of the va id Card in readiness for a PIN entry within 5 seconds.
If the Card and PIN combination are both va id the LED wi f ash Green for the un ock time and the Re ay wi
activate for the un ock period.
If no PIN is entered within 5 seconds S2 wi time out and the LED wi return to its norma red F ashing mode.
AND
S2 wi sound 3 beeps if the entered PIN is inva id or incorrect
Resetting / Restoring an Alarm
If an A arm occurs for any reason e.g. Door Forced Open or Open Too Long it can be reset by presenting A va id
card to the Reader or by entering the Master Code
OR
In icators / Warnings (LED an Buzzer)
Present Car to Rea er
Enter 4 Digit PIN followe by #
Present
a Vali
Car to Rea er
Enter
Master Co e followe by
#

10
Specifications
Features Description
Appearance Metal case, anti-explosion and anti-tamper
Waterproof IP65
Input voltage DC: 12-24V AC: 12-18V
Users(max) 2500
PIN 4 digits
Master Card Add/Delete User
Proximity Reader (RFID) Supports Wiegand 26bits, PIN/Wiegand output is a virtual number, Site
C
ode
/ Reader Address
is set within the
S2 C
ontroller
Connect External reader Can Connect any External EM/HID/IC readers with Wiegand 26 bit Output
Connect High Power Alarm
External Current of the Alarm <=3A
Dimensions
135mm x 57mm x 25mm
Operating Voltage
DC:12~24V AC: 12~18V
Current
Idle – 35mA / Active <80mA
Card Reading Distance
3~6 cm
Operating Temperature
-40~60 Deg C
Lock Output Load
2A Max
Head Office:
4/167 Prospect Hwy,
Seven Hi s NSW, Austra ia
Phone [phone]
emai : [email protected].au
Sydney Office - [phone]
Me bourne Office -[phone]
Brisbane Office - [phone]
Perth Office -[phone]
Ade aide Office - [phone]
Email
[e-mail]