HWH 625 Series User manual

OPERATOR’S MANUAL
ML38929/MP05.6032
10AUG06
Touch Panel Leveling Control
BI-AXIS Hydraulic Leveling
FEATURING:
HWH CORPORATION
(On I-80, Exit 267 South)
2096 Moscow Road | Moscow, Iowa 52760
Ph: 800/321-3494 (or) 563/724-3396 | Fax: [phone]
www.hwh.com
625 SERIES LEVELING SYSTEM
HWH COMPUTER-CONTROLLED
R
Straight-Acting Jacks
AP37456
R
(With Dump)
SPACEMAKER ROOM EXTENSION SYSTEMS
AND
R
RETRACT
EXTEND
HWH COMPUTERIZED LEVELING
SECURELY BEFORE REMOVING TIRES OR CRAWLING UNDER VEHICLE.
UNDERSTAND OPERATOR’S MANUAL BEFORE USING. BLOCK FRAME AND TIRES
EMERGENCY
STORE
AUTO
STOP
AUTO
LEVEL
TRAVEL
BRAKE
MODE
CAUTION!
EXCESS
SLOPE
NOT IN
PARK/
R
MANUAL
RETRACT
EXTEND
CORPORATION
W
HH
R
DUMP
MANUAL
Cap Extension
Engine Door Lift

CAUTION !
READ THE ENTIRE OPERATOR MANUAL BEFORE OPERATING.
BLOCK FRAME AND TIRES SECURELY BEFORE CRAWLING UNDER VEHICLE. DO NOT USE LEVELING JACKS OR
AIR SUSPENSION TO SUPPORT VEHICLE WHILE UNDER VEHICLE OR CHANGING TIRES. VEHICLE MAY DROP
AND/OR MOVE FORWARD OR BACKWARD WITHOUT WARNING CAUSING INJURY OR DEATH.
WEAR SAFETY GLASSES WHEN INSPECTING OR SERVICING THE SYSTEM TO PROTECT EYES FROM DIRT, METAL
CHIPS, OIL LEAKS, ETC. FOLLOW ALL OTHER APPLICABLE SHOP SAFETY PRACTICES.
OPERATOR’S MANUAL
KEEP ALL PEOPLE CLEAR OF VEHICLE WHILE DUMPING AIR FROM THE VEHICLE’S SUSPENSION.
DO NOT MOVE THE VEHICLE IF THE VEHICLE IS NOT AT THE PROPER RIDE HEIGHT. CONTACT MANUFACTURER
IMPORTANT: IF COACH IS EQUIPPED WITH A ROOM EXTENSION, READ ROOM EXTENSION SECTION BEFORE
OPERATING LEVELING SYSTEM.
HOW TO OBTAIN WARRANTY SERVICE
THIS IS NOT TO BE INTERPRETED AS A STATEMENT OF WARRANTY
HWH CORPORATION strives to maintain the highest level of
customer satisfaction. Therefore, if you discover a defect or
problem, please do the following:
[phone] OR [phone]. Give your name and
coach was purchased, or the date of system installation,
Notify the dealership where you purchased the
vehicle or had the leveling system installed. Dealership
management people are in the best position to resolve
the problem quickly. If the dealer has difficulty solving
the problem, he should immediately contact the Customer
Service Department, at HWH CORPORATION.
If your dealer cannot or will not solve the problem,
notify the Customer Service Department:
HWH CORPORATION 2096 Moscow Rd. Moscow IA. 52760
address, coach manufacturer and model year, date the
SECOND:
FIRST:
authorization of an independent service facility, to be
defective part, either by appointment at the factory or by the
CORPORATION will authorize repair or replacement of the
determine whether or not your claim is valid. If it is, HWH
HWH CORPORATION personnel will contact you to
during business hours (8:00 a.m. till 5:00 p.m. c.s.t.).
description of the problem, and where you can be reached
determined by HWH CORPORATION. All warranty repairs
must be performed by an independent service facility
authorized by HWH CORPORATION, or at the
HWH CORPORATION factory, unless prior written approval
has been obtained from proper HWH CORPORATION
personnel.
08FEB06
MP15.9800
TECHNICAL SERVICE FOR MOVING THE VEHICLE WHEN NOT AT THE PROPER RIDE HEIGHT.
KEEP ALL PEOPLE CLEAR OF VEHICLE WHILE OPERATING LEVELING SYSTEM OR ROOM EXTENSIONS.

MP25.3052
26JUN06
"EMERGENCY STOP" BUTTON:
any leveling system operation.
"AUTO LEVEL" BUTTON:
"AUTO STORE" BUTTON:
four jacks at the same time. WARNING LIGHTS:
"EXCESS SLOPE" LIGHT:
the leveling system cannot level the vehicle.
"NOT IN PARK/BRAKE" LIGHT:
when the hand/auto brake is not set and the "AUTO LEVEL"
"TRAVEL MODE" LIGHT:
when the ignition is on, when the jacks are retracted and
there are no red WARNING lights on.
MASTER "JACKS DOWN" WARNING LIGHT:
light mounted in the dash separate from the touch panel.
and the ignition is "ON".
BUZZER:
CONTROL FUNCTIONS
INDICATOR LIGHTS (CONTINUED)
CONTROL BUTTONS
Push this button to stop
Push this button to retract all
This indicator will light when
This indicator will light
This indicator light will be on
This is a
This is a jacks down warning.
EXTEND BUTTONS (UP ARROWS):
RETRACT BUTTONS (DOWN ARROWS):
LEVELING LIGHTS:
These buttons will
extend their respective jack pairs to lift the vehicle.
These buttons
will retract their respective jack pairs to lower the vehicle.
The four yellow indicating lights are
level sensing indicators. When a yellow light is on, it
indicates that its side, end, or corner of the vehicle is low.
No more than two lights should be on at the same time.Push this button any time to
The four red lights surrounding the
yellow level indicators are jacks down WARNING lights.
They are functional only when the ignition is in the "ON"
extended 1/4 to 1/2 inch.
start the automatic leveling function.
It will sound if the master "JACKS DOWN"
CONTROL IDENTIFICATION
625 SERIES LEVELING SYSTEM
COMPUTER-CONTROL
or "ACC" position, the system is on, and the jacks are
It will be on when any one or more jacks are extended
button is being pushed.
RETRACT
EXTEND
HWH COMPUTERIZED LEVELING
SECURELY BEFORE REMOVING TIRES OR CRAWLING UNDER VEHICLE.
UNDERSTAND OPERATOR’S MANUAL BEFORE USING. BLOCK FRAME AND TIRES
"EXCESS SLOPE"
Indicator light
"AUTO LEVEL"
AUTO LEVEL/STORE
CANCEL Button
"NOT IN PARK"
Indicator light
Indicator light
"TRAVEL MODE"
Indicator light
Indicator light
AUTO LEVEL
"AUTO STORE"
Button
STORE
Button
RAISE LEFT SIDE
Manual button
LOWER LEFT SIDE
Manual button
EMERGENCY
STORE
AUTO
STOP
AUTO
LEVEL
TRAVEL
BRAKE
MODE
CAUTION!
EXCESS
SLOPE
NOT IN
PARK/
R
LOWER FRONT
Manual button
RAISE FRONT
Manual button
JACK DOWN
Indicator light
RAISE RIGHT SIDE
Manual button
LOWER RIGHT SIDE
Manual button
LEVEL SENSING
Indicator light
(4) yellow
RAISE REAR
Manual button
LOWER REAR
Manual button
MANUAL
RETRACT
EXTEND (4) red
INDICATOR LIGHTS
AUTO LEVEL INDICATOR LIGHT: This light will flash
during the automatic leveling function.
STORE INDICATOR LIGHT: This light will flash during
the automatic store function.
When all four yellow LEVEL lights are out, the vehicle is
level.
MANUAL
DUMP
"MANUAL DUMP"
Button
warning light is on.
"MANUAL DUMP" BUTTON: This is a manual button for
dumping air from the vehicle suspension.

CONTROL FUNCTIONS
CONTROL IDENTIFICATION
MP25.9429
10AUG06
CORPORATION
H
CAUTION!
CLEAR OF ROOM WHEN OPERATING.
UNDERSTAND OPERATOR’S MANUAL BEFORE
USING. KEEP PEOPLE AND OBSTRUCTIONS
HYDRAULIC ROOM EXTENSION
OFF
ON
RETRACT
H
W
R
EXTEND FRONT CAP
CONTROL SWITCH
KEY SWITCH
CONTROL SWITCH is a two position momentary switch.
Pressing the switch in the EXTEND position will extend the
FRONT CAP. Pressing the switch in the RETRACT position
will retract the FRONT CAP. Releasing the FRONT CAP
CONTROL SWITCH will halt the operation of the
FRONT CAP OPERATOR’S PANEL
KEY
FRONT CAP CONTROL SWITCH: The FRONT CAP
cannot be removed. When the KEY SWITCH is in the
"OFF" position the front cap cannot be operated, and
"ON" position the front cap can be operated and the key
The KEY SWITCH controls power to the
FRONT CAP SWITCH. When the KEY SWITCH is in the
KEY SWITCH:
the key can be removed.
FRONT CAP.
The DOOR LIFT
of the DOOR LIFT.
DOOR LIFT CONTROL SWITCH will halt the operation
the switch down will close the DOOR LIFT. Releasing the
Pressing the switch up will open the DOOR LIFT. Pressing
CONTROL SWITCH is a two position momentary switch.
DOOR LIFT CONTROL SWITCH:
CAUTION:UNDERSTAND OWNER’S MANUAL
BEFORE OPERATING THE REAR ENGINE DOOR LIFT.
MAKE SURE THE AREA IN AND AROUND REAR ENGINE
IS CLEAR BEFORE OPERATING. ACTIVATE BOTH
MECHANICAL DOOR STOPS BEFORE WORKING IN
REAR ENGINE DOOR AREA.
OPEN
CLOSE

MP25.9995
14MAR12
CONTROL IDENTIFICATION
PUMP RUN TIME
SYSTEM VARIATIONS FOR PUMP RUN TIME
Contact HWH corporation to get specific information about the system in this vehicle.
No matter what HWH system is on the vehicle, the pump should not be ran for more than four minutes
(3" motors) or six minutes (3.7" or 4.5" motors) without allowing the pump motor to cool for thirty minutes.
Continuous operation of the pump motor without allowing the motor to cool can damage the pump motor.
Some HWH systems are equipped with a lighted reset switch.
If the processor turns the pump off because the run time has
been exceeded, the light in the reset switch will turn on. The
With some systems, when the processor has turned the pump off because the run time has been exceeded, power
to the HWH system must be turned off and back on before the system will operate. With motorized vehicles, turn the
ignition off and back on. With non-motorized vehicles, turn the master power switch for the HWH system off and back
DO NOT continue without allowing the pump motor to cool for thirty minutes.
When operating some leveling systems manually or operating the room extensions, the pump will turn off and back
on while pushing the control button when the pump run time has been exceeded.
the pump motor to cool for thirty minutes.
Some systems can be turned back on immediately after the processor turns the pump off.
back on or run the pump without allowing the pump motor to cool for thirty minutes.
Some systems with rooms run the rooms separate from the system processor. These systems do not monitor pump
run time when operating the rooms.
pump motor to cool for thirty minutes.
The HWH systems with a computer processor monitor the pump run time and will turn the pump off if the run time exceeds a
specified time. This time can vary with different systems. Due to available electronics or system design, the pump run time
programs will also vary. Leveling systems and room extensions that are not controlled by a system processor have no pump
run time protection.
thirty minutes.
Pump motors used with HWH leveling systems and room extension systems come in 3 different diameters; 3", 3.7" and 4.5".
Contact the vehicle manufacturer or HWH for help with identifying the motor size.
runs for more than four minutes with a 3" motor; or six minutes with a 3.7" or 4.5" motor that the motor is allowed
to cool for thirty minutes before continuing. Continuous operation of the pump motor without allowing the motor
PUMP RUN TIME
It is important that any time the pump
to cool can damage the motor.
DO NOT run the pump more than four or six minutes without allowing the pump motor to cool for
DO NOT run the pump more than four or six minutes without allowing the
DO NOT turn the system
DO NOT continue without allowing
on.
system will not operate until the reset switch is pushed.
DO NOT continue without allowing the pump motor to
cool for thirty minutes. LIGHTED RESET SWITCH
For cold weather information see "COLD WEATHER OPERATIONS" below.
COLD WEATHER OPERATIONS
HWH leveling and room extension systems are designed to function in cold weather down to 0 degrees Fahrenheit. Below
freezing (32 degrees Fahrenheit) the jacks or rooms will operate slower than usual.
For operation in temperatures dropping below -20 degrees Fahrenheit, it is necessary that the system is equipped with oil
designed for extreme cold weather application such as a synthetic oil. (Contact HWH for recommendations.)
DO NOT run the pump motor continuously.
Continuous operation of the pump with slow moving jacks or rooms in cold weather, without allowing the pump motor to
cool will cause the pump motor to burn up and damage the pump assembly.
It is important that any time the pump runs for more than four minutes
continuing. Continuous operation of the pump motor without allowing the motor to cool can damage the motor.
with a 3" motor; or six minutes with a 3.7" or 4.5" motor that the motor is allowed to cool for thirty minutes before

OPERATING PROCEDURES
MP35.381X
19NOV07
GENERAL INSTRUCTIONS
PREPARATION FOR TRAVEL
If parking on soft ground or asphalt paving, a wood block or
pad should be placed under each jack.
Any time a hydraulic leveling process is interrupted, retract
the jacks according to the JACK RETRACTION Section and
then restart the leveling process.
If the hand / auto brake is not set when the "AUTO LEVEL"
button is pressed, the "NOT IN PARK/BRAKE" light will
come on. When the "AUTO LEVEL" button is released the
If the jacks are retracted but a red "WARNING" light is lit
the system needs to be serviced.
If the jacks cannot be retracted according to the JACK
RETRACTION Section, retract the jacks according to the
MANUAL JACK RETRACTION Section. The system
should then be checked.
Maintain adequate clearance in all directions for vehicle, room
extensions, awnings, doors, steps, etc. Vehicle may move in
any direction due to jacks extending or retracting, settling of
the jacks or the vehicle, equipment malfunction, etc..
Any room extension or generator slide should be fully
DO NOT MOVE THE VEHICLE IF ONE
OR MORE JACKS ARE EXTENDED TO THE GROUND.
CAUTION:
"NOT IN PARK/BRAKE" light will go out. The Automatic
retracted before traveling.
Leveling function will not start.
Press the "EMERGENCY STOP" button or turn the ignition
switch "OFF" at any time to stop the operation of the system.
fail to retract completely, extend the jacks back down
to the ground then retract the jacks again.
NOTE: If the vehicle is parked or stored with the jacks
extended for an extended period of time and the jacks
IMPORTANT: Before traveling, the red jack warning
lights must be off the "TRAVEL MODE" light must be on
and he vehicle should be at the proper height for travel.
If lights are not correct for travel, retract jack as
THE LEVELING JACKS ARE STILL IN CONTACT WITH
THE GROUND OR IN THE EXTEND POSITION. THIS
VEHICLE IS EQUIPPED WITH STRAIGHT-ACTING JACKS.
MOVING THE VEHICLE WITH THE LEVELING JACKS
EXTENDED CAN CAUSE SEVERE DAMAGE TO THE
CAUTION:DO NOT MOVE THE VEHICLE WHILE
TRAVELING. CONTACT MANUFACTURER TECHNICAL
SERVICE BEFORE MOVING A VEHICLE THAT IS NOT
AT PROPER TRAVEL HEIGHT.
VEHICLE IS AT THE PROPER RIDE HEIGHT FOR
INTO THE STORE/TRAVEL POSITION AND THE
JACKS AND OR THE VEHICLE AND CREATE A DRIVING
HAZARD. DO NOT RELY SOLELY UPON WARNING
LIGHTS. IT IS THE OPERATOR’S RESPONSIBILITY
TO CHECK THAT ALL JACKS ARE FULLY RETRACTED
described in the JACK RETRACTION Section.

MP35.382R
17OCT06
AUTOMATIC HYDRAULIC LEVELING (HWH TOUCH PANEL CONTROLS)
1. Place transmission in the recommended position for
parking the vehicle and set parking brake. Turn the coach
engine off. Turn the ignition to the "ACCESSORY" position.
2. At this time, the operator may want to check the jacks
and place a pad under each jack if the ground will not
3. Press the "AUTO LEVEL" button one time.
The AUTO LEVEL light will start to flash. The system
5. Turn the ignition switch to the "OFF" position.
OPERATING PROCEDURES
625 SERIES LEVELING SYSTEM
support the vehicle.
EXCESS SLOPE SITUATION: In the event the jacks are
unable to level the coach, the "EXCESS SLOPE" light will
come on. Excess slope is two jacks fully extending without
turning the yellow level light out. The system will not stabilize
the vehicle if the "EXCESS SLOPE" light comes on. One or
more jacks may not be extended. The system will shut off
leaving the "EXCESS SLOPE" light on. The "EXCESS
SLOPE" light will remain on if the ignition is in the "ON" or
"ACC" position, until the jacks have been fully retracted
turning the red warning lights out. Push the "STORE" button
to retract the jacks. Move the vehicle to a more level position
or level the vehicle as close as possible according to the
MANUAL HYDRAULIC OPERATION section.
IMPORTANT: During the Automatic Leveling procedures,
pushing the "AUTO LEVEL", "AUTO STORE" or the
"EMERGENCY STOP" button on the HWH touch panel
will stop the automatic leveling function.
approximately 25 seconds, the leveling process will begin.
will begin to dump air from the vehicle suspension. After
CAUTION:
PERSONS AND OBJECTS ARE CLEAR OF THE VEHICLE.
BUTTON THE OPERATOR MUST BE SURE THAT ALL
PRIOR TO PUSHING THE "AUTO LEVEL"
AND THE VEHICLE WILL LOWER IMMEDIATLY AFTER
AIR WILL BE EXHAUSTED FROM THE VEHICLE SUSPENSION
THE "AUTO LEVEL" BUTTON IS PUSHED.
and the park brake is set.
NOTE: One or two yellow level indicator lights on
the leveling system touch panel can be on anytime
the vehicle ignition is in the ON or ACC. position light to "bump" the vehicle up slightly to turn that yellow
(extend jacks) that correspond to any lit yellow level indicator
set. If desired, the operator can use the UP ARROWS
ignition is in the ON or ACC. position and the park brake is
is the manual leveling buttons will function anytime the
home. However, a feature of the single step leveling system
normally is not sufficient to cause a level issue for the motor
The slight lift experienced during the stabilizing procedure
indicator light off.
the yellow level indicator lights off, the system will
then stabilize the vehicle. While the system is
stabilizing the vehicle, the yellow level indicator lights
are inhibited from coming on. Stabilizing the vehicle
ground that were not used to level the vehicle. This is
vehicle approximately one (1) inch. This "bumps" the
vehicle up slightly when stabilizing. Due to the ½
the red auto level indicator light turns off.
is accomplished by extending any jacks to the
done by monitoring a pressure switch on each jack.
Any jack used to stabilize the vehicle will lift the
degree accuracy tolerance of the sensing unit, one or
two yellow level indicator lights may come on after
AUTO LEVEL SEQUENCE: During the automatic
leveling sequence, after the system has extended the
appropriate jacks to level the vehicle and has turned

MP35.383F
17OCT06
JACK RETRACTION (HWH TOUCH PANEL CONTROLS)
OPERATING PROCEDURES
625 SERIES LEVELING SYSTEM
THE OPERATOR MUST BE SURE THAT CAUTION:
1. Start the engine. Press the "STORE" button immediately.
ALL PEOPLE ARE CLEAR OF THE VEHICLE.
THERE ARE NO OBJECTS UNDER THE VEHICLE AND THAT
DO NOT MOVE THE VEHICLE WHILE THE CAUTION:
while traveling, the jacks should be checked as soon as
IMPORTANT: If a red warning light and buzzer come on
THE STORE/TRAVEL POSITION AND THE VEHICLE IS AT
are inflated to the vehicles proper ride height.
the green "TRAVEL" light is on, and the suspension air bags
lights are out, the jacks are in the STORE/TRAVEL position,
2. The vehicle can be moved as soon as the red warning
CHECK THAT ALL JACKS ARE FULLY RETRACTED INTO
WARNING LIGHTS. IT IS THE OPERATOR’S RESPONSIBILITY TO
CREATE A DRIVING HAZARD. DO NOT RELY SOLELY UPON
SEVERE DAMAGE TO THE JACKS AND OR THE VEHICLE AND
WITH THE LEVELING JACKS EXTENDED CAN CAUSE
WITH STRAIGHT-ACTING JACKS. MOVING THE VEHICLE
OR IN THE EXTEND POSITION. THIS VEHICLE IS EQUIPPED
LEVELING JACKS ARE STILL IN CONTACT WITH THE GROUND 3. If the jacks fail to retract see the MANUAL JACK
RETRACTION section of this manual.
a safe parking location is found.
THE PROPER RIDE HEIGHT.
The store indicator light will flash and the jacks down
buzzer will sound as the vehicle suspension returns to ride
height and the jacks retract. The front jacks will retract for 2
seconds before the rear jacks begin to retract. Each jacks
red WARNING light will go out. The system will shut down
automatically either six minutes after the last WARNING
light goes out or thirty minutes after a warning light has
failed to go out.
IMPORTANT: Thermal expansion caused by heat
generated during travel can cause a jack to extend
slightly. Only an uninterrupted STORE cycle using the
"STORE" button will allow the system to monitor and
adjust for thermal expansion.
Manual or Emergency retraction of the jacks,
interruptions of power and/or the STORE cycle,
changing the ignition key position, pushing the
"EMERGENCY STOP", "AUTO LEVEL" or the "AUTO
STORE" button on the HWH touch panel or engaging
the remote AUTO LEVEL/STORE toggle switch during
the STORE cycle will void this system ability until the
STORE procedure is reran in it’s entirety.

OPERATING PROCEDURES
MP35.384H
08JAN07
MANUAL HYDRAULIC OPERATION
before front to rear.
low. It is best to level the vehicle side to side first, if needed,
exhausted from the vehicles suspension system.
3. Push and hold the "DUMP" until all of the air is
"ACCESSORY" position.
the vehicle, and set the parking brake. Turn the ignition to the
LEVEL SENSING light is on, that side or end of the vehicle is
(UP ARROW) buttons on the right half of the panel. If a yellow
4. The vehicle may be leveled using the manual EXTEND
the vehicle on the jacks.
2. Place pads under the jack feet if the ground will not support
1. Place transmission in the recommended position for parking
stabilize the vehicle after leveling is complete should lift the
IMPORTANT: Push the "STORE" button before traveling
when manual operation of the leveling system is used.
against wind and activity in the vehicle. Jacks used to
touch panel and turn the ignition switch to the "OFF" position.
5. When leveling is completed, push the "OFF" button on the
button for more than ten (10) seconds after that pair of
extended to the ground. This provides additional stability
or end of the vehicle. Any jack not used for leveling can be
Jacks will extend (or retract) in pairs to raise (or lower) a side
IMPORTANT: Do not continue to push an EXTEND
vehicle slightly after touching the ground.
jacks are fully extended.
NOTE: With some systems, the "DUMP" button may be
momentary. With this system the "DUMP" button must
be pushed and held until the air is exhausted from the
suspension.

OPERATING PROCEDURES
MP35.384N
01MAR10
MANUAL JACK RETRACTION
been opened far enough to allow the jacks to retract.
the T-Handle will turn harder. Make sure the valves have
will turn several turns easily. As the valve starts to open,
Large style with T-Handle valve release:
power unit. The upper most manifold should control
NOTE: Multiple manifolds may be present on the
retract the jacks.
if the STORE feature on the HWH control panel will not
Use the manual valve release for retracting the jacks only
DO NOT CRAWL UNDER THE VEHICLE, KEEP A SAFE
DISTANCE IN FRONT AND REAR OF THE VEHICLE.
THE VEHICLE MAY DROP AND/OR MOVE FORWARD
OR BACKWARD WITHOUT WARNING AS THE VALVE
RELEASE IS OPERATED.
1. Locate your power unit-manifold assembly.
2. Allow clearance for the vehicle to lower.
WARNING:KEEP AWAY FROM THE WHEELS,
point as internal damage may occur to the solenoid.
incorporated into the Breather Cap. Before using read
NOTE: As of APRIL 2002 a 1/4" Nut Driver has been
and understand the last page of this manual.
6. Check that all jacks are now retracted. If yes, continue.
7. Close the valves by turning each valve release clockwise.
DO NOT tighten the manual valve release past this
IMPORTANT: Once the manual valve release is snug,
8. The system should now be repaired before using again.
3. Using the diagram below identify the style
5. Repeat the process by identifying then opening
the two outer valves, if applicable.
LARGE STYLE
WITH T-HANDLE
VALVE RELEASE
SMALL STYLE
WITH VALVE
RELEASE NUT
LARGE STYLE
RELEASE NUT
WITH VALVE
PLASTIC PLUG
BREATHER
CAP
Small style with Valve Release Nut: DO NOT
1/4" valve release nut more than . Turning
the nut more could damage the valve.
The T-Handle
turn the
jack functions. (Valve styles and arrangements will vary)
POWER UNIT-MANIFOLD ASSEMBLY
MANIFOLD
of your two center valves.
If no, notify the dealership where you purchased the vehicle
or had the leveling system installed or contact
(The diagram below represents a typical Power Unit-
MANUAL JACK RETRACTION
extensions are fully retracted prior to performing
IMPORTANT: HWH recommends that all HWH room
manual jack retraction procedures.
Manifold Assembly it may not be an exact match to yours). 4. Retract the front jacks by opening the two center valves. Slowly turn the manual valve releases counter clockwise
until the jacks start to retract.
4 and 1/2 turns
HWH Corporation customer service.
valve. Replace the protective plastic plug.
Turning the nut more could damage the
release nut more than
The 1/4" Valve
removed to gain access. Open valve 1-1/2 to 2 full turns.
release nut is located under a plastic plug that must be
turn the 1/4" valve
Large style with Valve Release Nut:
2 full turns.
DO NOT
MP35.601G