Behringer 902 User manual

Quick Start Guide
902 VOLTAGE
CONTROLLED AMPLIFIER
Legendary Analog VCA Module
for Eurorack
Controls
(1) CONTROL MODE (LIN/EXP) rocker switch toggles
between linear and logarithmic response modes.
(2) FIXED CONTROL VOLTAGE knob allows you to manually
set a control voltage.
(3) SIG IN input jacks accept audio and control signals over
cables with 3.5 mm TS connectors. These dual inputs
allow the unit to amplify two signals simultaneously.
(4) SIG OUT output jacks send out amplied audio and control
signals over cables with 3.5 mm TS connectors.
(5) CONTROL INPUTS accept control voltage signals from
other modules to change the amplication level.
Power Connection
The 902 VCA comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these steps
to connect power to the module. It is easier to make these
connections before the module has been mounted into a
rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the
red stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of xed holes
spaced 2 HP apart along the length of the case, or a track that
allows individual threaded plates to slide along the length
of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded plate.
Attach the screws part way to start, which will allow small
adjustments to the positioning while you get them all aligned.
After the nal position has been established, tighten the
screws down.
(1)
(3)
(2)
(4)
(5)

Specications
Controls
Control Mode Rocker switch
Linear / exponential,
switchable
Fixed Control Voltage 1 x rotary knob
0 - 6 V, selectable
Signal Connections
Signal in 2 x 3.5 mm TS jack, mono
Impedance 9 kΩ unbalanced
Signal out 2 x 3.5 mm TS jack, mono
Impedance 1.1 kΩ unbalanced
Output noise < -78 dBu @ unity gain,
22 Hz - 22 kHz
Control inputs 3 x 3.5 mm TS jack, mono
Impedance 100 kΩ unbalanced
CV input range -6 V to +6 V
Power
Power supply Eurorack
Current draw 50 mA (+12 V),
45 mA (-12 V)
Physical
Dimensions 40 x 129 x 35 mm
(1.6 x 5.1 x 1.4")
Rack units 8 HP
Weight 0.09 kg (0.20 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and
other information are subject to change without notice. All trademarks are the
property of their respective owners. Midas, KlarkTeknik, Lab Gruppen, Lake,
Tannoy,Turbosound, TC Electronic,TC Helicon, Behringer, Bugera, Auratone
and Coolaudio are trademarks or registered trademarks of MusicTribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2019 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding MusicTribe’s Limited Warranty, please see complete details online
at musictribe.com/warranty.
Zhongshan Eurotec Electronics Limited
No. 10 Wanmei Road, South China Modern Chinese Medicine Park,
Nanlang Town, 528451, Zhongshan City, Guangdong Province, China