NETGEAR Wg111v2 - Usb Wifi Card Includes Driver Cd Manual

1
v3.0, January 2007
Basic Setup
The NETGEAR 54 Mbps Wireless USB2.0 Adapter WG111v2 lets you connect a PC computer to
wireless networks. It is designed for PC computers running Microsoft Windows. For information
about product features and compatible NETGEAR products, please see the NETGEAR website at
http://www.netgear.com.
This chapter describes how to install your wireless USB adapter and set up basic wireless
connectivity on your Wireless Local Area Network (WLAN). Advanced wireless network set up is
covered in “Network Connections and Wireless Security” on page 11.
What You Need Before You Begin
You must verify that your computer meets the minimum system requirements and identify the
wireless network settings of the wireless network where you will connect before you can set up
your wireless USB adapter and connect.
Verify System Requirements
Before installing the Wireless Adapter, make sure that these minimum requirements have been
met. You must have a computer with:
• A Pentium300 MHz or higher compatible processor with an available USB port.
•ACDdrive.
• 10 MB of free hard disk space.
• Windows 2000, XP, or Vista.
Observe Wireless Location and Range Guidelines
Computers can connect over wireless networks indoors at a range which vary significantly based
on the location of the computer with the Wireless Adapter. For best results, avoid potential sources
of interference, such as:
• Large metal surfaces
• Microwave ovens
• 2.4 GHz Cordless phones

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
2
v3.0, January 2007
In general, wireless devices can communicate through walls. However, if the walls are constructed
with concrete, or have metal, or metal mesh, the effective range will decrease if such materials are
between the devices.
What Is in the Box
The product package should contain the following items:
• NETGEAR 54 Mbps Wireless USB2.0 Adapter WG111v2
• Installation Guide
• Plastic cradle and fasteners to hold the WG111v2
•NETGEAR CD, including:
– Driver and Configuration Utility Software
– This User Manual
• Warranty and Support information card
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the
carton, including the original packing materials, in case you need to return the product.
Default Wireless Settings
If this is a new wireless network installation, use the factory default settings to set up the network
and verify wireless connectivity. If this is an addition to an existing wireless network, you need the
wireless network and wireless security settings that are already defined.
Your Wireless Adapter factory default basic settings are:
• Network Name Service Set Identification (SSID): ANY
• Network Mode (Infrastructure or Ad-hoc): Infrastructure
• Data security WEP, WPA2-PSK, or WPA-PSK encryption: Disabled
The section below provides instructions for setting up the Wireless Adapter for basic wireless
connectivity to an access point.
Note: In order for the Wireless Adapter to communicate with a wireless access point
or wireless adapter, all devices must be set up to use the same wireless network
name (SSID).

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
3
v3.0, January 2007
Installation Instructions
The instructions in this chapter are for an Access Point (Infrastructure) installation. Wireless
security, advanced settings, and Computer-to-Computer (Ad Hoc) instructions are covered in
“Network Connections and Wireless Security” on page 11.
Follow the instructions below to install the Wireless Adapter.
1. First, install the software. Insert the NETGEAR CD. If the CD main page does not appear,
double click Autorun.exe on the CD.
a. Click Install the Software.The Check for Updates window will open.
b. If you are connected to the Internet, click Check for Updates. If not, you can choose to
install from the CD.
c. When the Installation Complete message appears, click Next.
d. On the Smart Wizard screen, click Next to proceed with the Smart Wizard setup.
2. Now, when prompted, insert your wireless USB adapter.
a. Click Next to proceed. Windows will discover the adapter and continue the software
installation process.
Figure 1

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
4
v3.0, January 2007
b. Follow the Windows prompts to complete the software installation.
c. If a Windows logo certification warning appears, click Continue to proceed with the
installation.
d. When the Windows software installation is complete, click Finish.
3. Windows 2000 users go to Step 4. Windows XP or Vista users can set up the wireless adapter
either with the NETGEAR Smart Wizard (recommended) or the Windows Configuration
Utilities.
•NETGEAR Smart Wizard: Reveals more information about each network and makes it
easier to troubleshoot network connection problems. See “The Smart Wizard Status Bar”
on page 7 and “Statistics Page” on page 26.
•Windows Zero Configuration Utility: See the Windows documentation or see the link to
“Windows XP and Vista Wireless Configuration Utilities” on page 35.
Figure 2
Figure 3

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
5
v3.0, January 2007
4. Use the Smart Wizard to set up your Wireless Adapter
a. When prompted, click Next to let the wizard help you connect to a network
(recommended).
b. Select the wireless network from the drop-down list, and the wizard records your choice.
If the network uses security, then the Smart Wizard detects it..
c. Follow the Wizard steps for Security (if used) and for saving a Profile.
d. After you have reviewed the settings, click Finish.
Figure 4
Note: Hidden networks do not broadcast the Network Name (SSID). These
networks are in the drop-down list, but the Network Name (SSID) is blank
Figure 5

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
6
v3.0, January 2007
The icon appears in the System Tray and on the desktop. The wizard initiates your
wireless connection. It could take up to a minute for your wireless connection to be
established.
The Smart Wizard Settings page opens.
5. Use the status bar to verify your wireless connectivity. For more information about
connecting, see “Connecting to Wireless Networks and the Internet” on page 6.
Connecting to Wireless Networks and the Internet
The Wireless Adapter has indicators that show the status of your connection to a wireless network
and to the Internet:
• Icon: After you install the software, this icon appears on the desktop and in the lower
right of the Windows task bar. It is color coded to show the status of the connection. See “The
Smart Wizard Status Bar” on page 7.
•Smart Wizard Status Bar: Clicking on the system tray icon opens the Smart Wizard. The
status bar at the bottom of the page shows details about your wireless and Internet connection.
Figure 6

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
7
v3.0, January 2007
The Smart Wizard Status Bar
Click the icon to open the Smart Wizard so you can view the status bar. The Smart Wizard
Settings page opens. The status bar is at the bottom of the page.
•Connection Status: The color shows the connection status.
•Signal Strength: Shows the signal strength of the wireless network. If the signal is poor, then
try moving closer to the wireless access point.
•Lock icon: Shows if security is used on the network.
•Router/Internet connection indicator: This shows the progress of your connection. By
default, this feature is on.
If you selected Europe during the WG111v2 installation, this feature is disabled.
The Router/Internet connection indicator is useful in isolating a problem. For example, if you are
connected to a router, but not to the Internet, then check the router’s Internet connection.
If you right-click the System Tray icon, you can disable the Internet notification feature by
clearing the check mark on this line. If you do so, then only the IP address is shown.
Figure 7
Figure 8
Connection Indicator Description
Connected to Internet
or IP Address Wireless Internet connection OK.
Connected to Router Wireless connection to router OK but no Internet
connection at router.
___.___.___.___ or
169.254..x.x Wireless connection to a router OK but there is a problem with the router. See “Troubleshooting”.
signal strength
Unlocked: Network does not use security
Locked: Network uses security
Router/Internet
connection
connection indicator
status

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
8
v3.0, January 2007
If you selected Europe during the WG111v2 installation, you will not see the “Enable Internet
Connected Notification” option.
Icon Colors
The icon is on the desktop and in the Windows System Tray. The System Tray resides on one end
of the taskbar in the Microsoft Windows desktop.
Placing the USB Adapter Cradle
You can attach the Wireless Adapter directly to a USB port on your computer, or use the USB
cable to extend the range and obtain better wireless reception.
Follow these instructions to use the USB cable, plastic cradle, and loop and hook fastener provided
in the package for better USB Adapter placement on a notebook computer:
1. The Wireless Adapter comes with three black fasteners. Locate the one that has a prickly side
and attach it to the plastic cradle on the middle of the outside rear.
2. Insert the Wireless Adapter in the plastic cradle.
Figure 9
Color Condition Description
Red The wireless USB adapter
has no connection to any
other wireless node.
The Wireless Adapter can not link to any other wireless node
or the link is lost. Check your configuration or try moving to a
location where the wireless signal quality is better.
Yellow The wireless USB adapter
has a connection with another
wireless node.
The wireless link is weak. You may need to move to a better
spot, such as closer to the wireless access point. Also, look
for possible interference such as a 2.4 GHz cordless phone or
large metal surface.
Green The wireless USB adapter
has a connection with another
wireless node.
The wireless USB adapter has established good
communication with an access point and the signal quality is
strong.

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
9
v3.0, January 2007
3. Place one of the other pieces of loop and hook fastener on the back of the monitor near the top
for better reception.
4. Join the pieces of the fastener to attach the USB Adapter in the plastic cradle to the notebook
or desktop monitor.
See the installation instructions for your operating system before attaching the USB cable to the
USB Adapter and your computer
Removing the Software
You can remove the Wireless Adapter software in these two ways:
• Navigate the Windows Start menu to the NETGEAR 54 Mbps Wireless USB2.0 Adapter
WG111v2 program group, select the uninstall option, and follow the screen prompts.
• Navigate the Windows Start menu to the Control Panel Add or Remove Program item, select
the NETGEAR 54 Mbps Wireless USB2.0 Adapter WG111v2 option, and follow the screen
prompts.
Tip: Place the last piece of fastener on the side of monitor nearest your wireless
access point.
Figure 10

NETGEAR 54 Mbps Wireless USB 2.0 Adapter WG111v2 User Manual
10
v3.0, January 2007
Upgrading the Wireless Adapter Software
Upgrades may be available at the NETGEAR website. To install an upgrade, follow these steps.
1. Go to http://kbserver.netgear.com
2. Click the latest version of upgrade.
3. Examine the Release Note. Make sure to read any warnings and Known Problems.
4. Download the upgrade using the link in the Release Note.
5. Follow the Release Note installation instructions.