NETGEAR DGN2200v1 User manual

Version 1.1
VPN Configuration of ProSafe Client and Netgear DG Router
Prerequisites:
Software: VPNGL02 or VPNGL05 (Version 5.04)
Hardware: Netgear DSL router with VPN support, PC with Windows XP, Vista or 7.
Introduction:
This document will guide you on how to create a VPN policy for any of the home DSL gateways
that support VPN, as well as how to configure the VPN Pro-Safe VPN client in order to allow a
Virtual Private Network to be established over the internet.

Version 1.1
Checklist:
As we configure the Netgear DSL VPN Gateway, there will be information we’ll add which will
later be used in the configuration of the ProSafe Client Software. This information will be marked
with red numbered circles. The values we will use for this guide are already filled as light grey.
You can print this form to help keep track of this information.
Pre-Shared Key: _ _______________ 12345678 _
Client Identifier: ____ _____ _____client.com _
Router Identifier: __________ _____router.com _
Client’s IP Address: ________ _ _ __192.168.100.1 _
Router’s Network Address: ______ ___192.168.0.0 _
Router’s Network Mask: _ __ _______ 255.255.255.0 _
Router’s WAN IP Address: _ _____________ _86.41.176.179 _
➊
➋
➌
➍
➎
➏
❼

Version 1.1
Configuration of the VPN Policy on the DSL Gateway:
From the Router’s GUI, go to
VPN policies under Advanced –
VPN.
Click on Add Auto Policy.
➊The pre-shared key value
goes here.
This is your Pre-Shared Key.
➋Here we select “Fully
Qualified Domain Name”and
we give the client a name
This is your Client Identifier.
➌Here we select “Fully
Qualified Domain Name”and
we give the router a name
This is your Router Identifier.
➍Here we select “Single
Address”and we specify the
IP.
This is your Client’s IP
Address.
➎- ➏Here we select “Subnet
Address”and add the address
and mask of our router.
This is your Router’s
Network Address and
Router’s Network Mask.
To accept this settings, click
on “Apply”
➋
➌
➊
➏
➎
➍

Version 1.1
Configuration of the VPN Policy on the ProSafe Client:
Before you start configuring the VPN Client, go through the Checklist at the start and make sure
you have all the information listed there.
After installing the VPN Client
Software, click on the plus sign to
open the configuration panel.
Right click on “VPN Configuration”
and add a new Phase 1. It will be
added with the name Gateway.

Version 1.1
Click on gateway.
❼The Remote Gateway field will be
the value of your Router’s WAN
IP Address.
➊Input the Pre-Shared Key that
you have used when creating the
VPN Policy on the Router and
click on the OK Button.
Next, tick the checkbox next to
Use: Secure Gateway Tunnel.
➋The Local ID Type is DNS, and the
Value for the ID is your Client
Identifier.
➌The ID Type field will be the value
of your Router Identifier.
➌
❼
➊
➋

Version 1.1
With this, the configuration is completed. Now we can try our VPN configuration and connect to
our router.
Right click on the Phase 1 and
click on New Phase 2. It will be
added with the name “Tunnel”.
Click on Tunnel.
➍Here we enter the Client’s IP
Address.
➎Here we add the Router’s
Network Address.
➏Here we add the Router’s
Network Mask.
Make sure PFS is enabled with
DH2 (1020) Group.
After you are done, click on
Save.
➍
➎
➏

Version 1.1
Connecting:
To connect the VPN Tunnel we configured, do the following:
Go to Tools and click on Connection
Panel.
Double click on the tunnel we
created.
The tray notice box should tell us we
are connected.
The Connection Panel should show a
green button indicating we are
connected.
Now we should be able to access the resources at the DSL Gateway’s network from our Client
PC.