NETGEAR JDGN1000 User manual

NETGEAR JDGN1000
User Manual

NETGEAR JDGN1000 User Manual
i
Contents
1 Safety Precautions ..........................................................................................2
2 Overview.........................................................................................................2
2.1 Application ..........................................................................................2
2.2 Features..............................................................................................2
2.3 Standards Compatibility and Compliance ............................................2
3 Hardware Description and Hardware Installation .............................................2
3.1 Hardware Description..........................................................................2
3.1.1 Front Panel...............................................................................2
3.1.2 Rear Panel ...............................................................................2
3.2 Hardware Installation...........................................................................2
3.2.1 Choosing the Best Location for Wireless Operation..................2
3.2.2 Connecting the Device..............................................................2
4 PC Network Configuration and Login...............................................................2
4.1 PC Network Configuration...................................................................2
4.2 Logging In to the DSL Router..............................................................2
5 Web-Based Management................................................................................2
5.1 Setup Wizard.......................................................................................2
5.2 Add WPS Client ..................................................................................2
5.3 Setup ..................................................................................................2
5.3.1 Adsl Settings.............................................................................2
5.3.2 Basic Settings...........................................................................2
5.3.3 Interface Grouping....................................................................2
5.3.4 Wireless Settings......................................................................2
5.4 Content Filtering..................................................................................2
5.4.1 Logs .........................................................................................2
5.4.2 Block sites................................................................................2
5.4.3 Block Services..........................................................................2
5.5 Maintenance .......................................................................................2
5.5.1 Router Status............................................................................2
5.5.2 Attached Devices......................................................................2
5.5.3 Backup Settings........................................................................2
5.5.4 Set Password ...........................................................................2

NETGEAR JDGN1000 User Manual
ii
5.5.5 Router Upgrade........................................................................2
5.5.6 Logout ......................................................................................2
5.6 Advanced............................................................................................2
5.6.1 Wireless Settings......................................................................2
5.6.2 Wireless Repeating Function....................................................2
5.6.3 Port Forwarding / Port Triggering..............................................2
5.6.4 WAN Setup...............................................................................2
5.6.5 LAN Setup................................................................................2
5.6.6 QoS Setup................................................................................2
5.6.7 Dynamic DNS...........................................................................2
5.6.8 Static Routes ............................................................................2
5.6.9 Remote Management ...............................................................2
5.6.10 UPnP...................................................................................2

NETGEAR JDGN1000 User Manual
1
1 Safety Precautions
Read the following information carefully before operating the device. Please follow
the following precaution items to protect the device from risks and damage caused
by fire and electric power:
Use volume labels to mark the type of power.
Use the power adapter that is packed within the device package.
Pay attention to the power load of the outlet or prolonged lines.An
overburden power outlet or damaged lines and plugs may cause electric
shock or fire accident. Check the power cords regularly. If you find any
damage, replace it at once.
Proper space left for heat dissipation is necessary to avoid any damage
caused by overheating to the device. The holes on the device are designed
for heat dissipation to ensure that the device works normally. Do not cover
these heat dissipation holes.
Do not put this device close to a place where a heat source exists or high
temperature occurs.Avoid the device from direct sunshine.
Do not put this device close to a place where is over damp or watery. Do not
spill any fluid on this device.
Do not connect this device to any PC or electronic product, unless our
customer engineer or your broadband provider instructs you to do this,
because any wrong connection may cause any power or fire risk.
Do not place this device on an unstable surface or support.

NETGEAR JDGN1000 User Manual
2
2 Overview
The DSL Router is a highly ADSL2+ Integrated Access Device and can support
ADSL link with downstream up to 24 Mbps and upstream up to 1 Mbps. It is
designed to provide a simple and cost-effective ADSL Internet connection for a
private Ethernet or 802.11g/802.11b/802.11n wireless network. The Router
combines high-speed ADSL Internet connection, IP routing for the LAN and
wireless connectivity in one package. It is usually preferred to provide high access
performance applications for the individual users, the SOHOs, and the small
enterprises.
The Router is easy to install and use. The Modem connects to an Ethernet LAN or
computers via standard Ethernet ports. The ADSL connection is made using
ordinary telephone line with standard connectors. Multiple workstations can be
networked and connected to the Internet by a single Wide Area Network (WAN)
interface and single global IP address. The advanced security enhancements,
packet filtering and port redirection, can help protect your network from potentially
devastating intrusions by malicious agents from outside your network.
Network and Router management is done through the web-based management
interface that can be accessed through the local Ethernet using any web browser.
You may also enable remote management to enable configuration of the Router via
the WAN interface.
2.1 Application
Home gateway
SOHOs
Small enterprises
Higher data rate broadband sharing
PC file and application sharing
Network and online gaming
2.2 Features
User-friendly GUI for web configuration

NETGEAR JDGN1000 User Manual
3
Several pre-configured popular games. Just enable the game and the port
settings are automatically configured.
Compatible with all standard Internet applications
Industry standard and interoperable DSL interface
Simple web-based status page displays a snapshot of system configuration,
and links to the configuration pages
Downloadable flash software updates
Support for up to 8 permanent virtual circuits (PVC)
Support for up to 8 PPPoE sessions
WLAN with high-speed data transfer rates of up to 130 Mbps, compatible
with IEEE 802.11b/g/n, 2.4GHz compliant equipment
Optimized Linux 2.6 Operating System
IP routing and bridging
Asynchronous transfer mode (ATM) and digital subscriber line (DSL)
support
Point-to-point protocol (PPP)
Network/port address translation (NAT/PAT)
Quality of service (QoS)
Wireless LAN security: WPA, 802.1x, RADIUS client
Universal plug-and-play(UPnP)
File server for network attached storage (NAS) devices
Print server
Web filtering
Management and control
- Web-based management (WBM)
- Command line interface (CLI)
- TR-069 WAN management protocol
Remote update
System statistics and monitoring
DSL router is targeted at the following platforms: DSL modems, wireless
access points and bridge.
2.3 Standards Compatibility and Compliance
Support application level gateway (ALG)
ITU G.992.1 (G.dmt)

NETGEAR JDGN1000 User Manual
4
ITU G.992.2 (G.lite)
ITU G.994.1 (G.hs)
ITU G.992.3 (ADSL2)
ITU G.992.5 (ADSL2+)
ANSI T1.413 Issue 2
IEEE 802.3
IEEE 802.3u
IEEE 802.11b
IEEE 802.11g
IEEE 802.11n

NETGEAR JDGN1000 User Manual
5
3 Hardware Description and Hardware Installation
3.1 Hardware Description
3.1.1 Front Panel
Figure 1 Front panel
The following table describes the indicators on the front panel.
Indicator Color Status Description
On The device is powered on and the device
operates normally.
Blink The software is upgrading.
Green
Off The device is powered off.
On The device is initiating.
Power
Red Blink The software is upgrading.
On DSL link has established.
Blink slowly No DSL link is detected.
Blink quickly The DSL line is training.
DSL Green
Off Device is powered off.
On PPP/DHCP takes effect.
Blink slowly PPP/DHCP is negotiating.
Green Blink quickly Data is being transmitted.
Internet
Red On The Internet authentication fails or the
device is in the bridge mode.
On The Ethernet interface is connected.
Blink Data is being transmitted through the
Ethernet interface.
LAN
1/2/3/4 Green
Off The Ethernet interface is disconnected.

NETGEAR JDGN1000 User Manual
6
Indicator Color Status Description
On WLAN is enabled.
Blink Data is being transmitted through the
wireless interface.
WLAN Green
Off WLAN is disabled.
On Connection succeeds under Wi-Fi
Protected Setup.
Blink Negotiation is in progress under Wi-Fi
Protected Setup.
WPS Green
Off Wi-Fi Protected Setup is disabled.
3.1.2 Rear Panel
Figure 2 Rear panel
The following table describes the interfaces or the buttons on the rear panel.
Interface Description
Line RJ-11 port, for connecting the ADSL cable.
WLAN WLAN switch, for enabling or disabling the WALN function.
RESET Press the button for at least 1 second and then release it. System
restores the factory default settings.
WPS This button is used for enabling WPS PBC mode. If WPS is enabled, press this button, and then the wireless router starts to accept the
negotiation of PBC mode.
LAN 4~1
RJ-45 port, for connecting the router to a PC or another network
device.
Power Power interface, for connecting the power adapter.
ON/OFF Power switch
Warning:

NETGEAR JDGN1000 User Manual
7
Do not press the Reset button unless you want to clear the current settings. The
Reset button is in a small circular hole on the rear panel. If you want to restore the
default settings, please press the Reset button gently for 1 second with a fine needle
inserted into the hole and then release the button. The system reboots and returns to
the factory defaults.
The power specification is 12V, 1A. If the power adapter does not match the
specification, it may damage the device.
3.2 Hardware Installation
3.2.1 Choosing the Best Location for Wireless Operation
Many environmental factors may affect the effective wireless function of the DSL
Router. If this is the first time that you set up a wireless network device, read the
following information:
The access point can be placed on a shelf or desktop, ideally you should be able to
see the LED indicators in the front, as you may need to view them for troubleshooting.
Designed to go up to 100 meters indoors and up to 300 meters outdoors, wireless
LAN lets you access your network from anywhere you want. However, the numbers of
walls, ceilings, or other objects that the wireless signals must pass through limit signal
range. Typical ranges vary depending on types of materials and background RF
noise in your home or business.
3.2.2 Connecting the Device
Please follow the steps below to connect the device.
Step1 Connect the Line port of the DSL router with a telephone cable.
Step2 Connect the LAN port of the DSL router to the network card of the PC via
an Ethernet cable.
Step3 Plug one end of the power adapter to the wall outlet and connect the
other end to the Power port of the DSL Router.
The followig figure displays the connection of the DSL router, PC, and telephones.

NETGEAR JDGN1000 User Manual
8
Figure 3 Connecting the DSL router

NETGEAR JDGN1000 User Manual
9
4 PC Network Configuration and Login
4.1 PC Network Configuration
Each network interface on the PC should either be configured with a statically defined
IP address and DNS address, or be instructed to automatically obtain an IP address
using the network DHCP server. DSL router provides a DHCP server on its LAN and
it is recommended to configure your LAN to automatically obtain its IP address and
DNS server IP address.
The configuration principle is identical but should be carried out differently on each
operating system.
The following displays the TCP/IP Properties dialog box on Windows XP.

NETGEAR JDGN1000 User Manual
10
Figure 4 IP and DNS configuration
TCP/IP configuration steps for Windows XP are as follows:
Step1 Choose Start > Control Panel > Network Connections.
Step2 Right-click the Ethernet connection icon and choose Properties.
Step3 On the General tab, select the Internet Protocol (TCP/IP) component
and click Properties.
Step4 The Internet Protocol (TCP/IP) Properties window appears.

NETGEAR JDGN1000 User Manual
11
Step5 Select the Obtain an IP address automatically radio button.
Step6 Select the Obtain DNS server address automatically radio button.
Step7 Click OK to save the settings.
4.2 Logging In to the DSL Router
To log in to the DSL router, do as follows:
Step1 Open a Web browser on your computer.
Step2 Enter http://192.168.1.1 (the default IP address of the DSL router) in the
address bar. The login page appears.
Step3 Enter the user name and the password. You need not enter the
username and the password again if you select the option Remember
my password. It is recommended to change these default values after
logging in to the DSL router for the first time.
Step4 Click OK to log in to the Web page. Otherwise, please click Cancel to exit
the login page.
Figure 5 Login page
After logging in to the DSL router as a super user, you can query, configure, and
modify all the settings, and diagnose the system.

NETGEAR JDGN1000 User Manual
12
5 Web-Based Management
This chapter describes how to use Web-based management of the DSL router, which
allows you to configure and control all of DSL router features and system parameters
in a user-friendly GUI.
5.1 Setup Wizard
Click Setup Wizard. The page shown in the following figure appears.
Figure 6 Setup Wizard page
Step1 Select the country where you are from the drop-down list and then select
Yes if you want to use the Smart Setup Wizard.
Select No. I want to configure the router myself If you don’t want to use the
Smart Setup Wizard and want to configure the router manually
Step2 After PVC detection is selected, the following page appears if PVC
detection fails.
.
Note: The country code selection is for non-US model only and is not available to all US model. Per FCC
regulation, all WiFi product marketed in US must fixed to US operation channels only.
Figure 7 No Internet Connection Detected

NETGEAR JDGN1000 User Manual
13
out the causes in detail and then click Retry.
Step3 The following page appears when Internet connection detection is in
process.
Figure 8 Detection in process
Step4 The following page appears if no internet connection is detected.
Figure 9 No Internet Connection Detected
It means the PVC provided by your ISP is not among PVC automatic detection lists,
and then click Basic Setup to configure manually.
Step5 If Setup Wizard detects that the internet service provided by your ISP is
accessed through IPoA, the following page appears.
Figure 10 IPoA Detected
Click Next to configure IPoA connection. Here you can refer to the Help on the right
to configure.
For there is no ADSL synchronization, you can also refer to Help on the right to find

NETGEAR JDGN1000 User Manual
14
Figure 11 IPoA connection configuration
Step6 If Setup Wizard detects that the internet service provided by your ISP is
accessed through PPPoE, the following page appears.
Figure 12 PPPoE Detected
Click Next to configure your PPPoE connection. Here you can refer to Help on the
right to configure.

NETGEAR JDGN1000 User Manual
15
Figure 13 PPPoE Configuration
Step7 Click Apply to save the settings. Then IPTV detecting dialog box
appears.
Figure 14 IPTV detecting dialog box
If your ISP provides IPTV service, you can click Next to start IPTV detection.
If your ISP doesn’t provide IPTV service, you can click Skip to complete the
Setup Wizard configuration.
Step8 The following page shows that IPTV connection detection is in process.
Figure 15 IPTV Connection Detecting
Step9 If the detection fails, the following page appears.
Figure 16 No IPTV Connection Detected
It indicates that the PVC provided by your ISP is not among the PVC automatic
detection lists, and then you can click Basic Setup to configure manually.
Step10 If IPTV connection is successfully detected, the following page appears.

NETGEAR JDGN1000 User Manual
16
Figure 17 IPTV Connection Detected Successful
It shows Setup Wizard has configured IPTV connection for you. Click Setup to
enter Interface Grouping page, click Cancel to complete Setup Wizard
configuration.
5.2 Add WPS Client
Click Add WPS Client and the page shown in the following figure appears.
Figure 18 Add WPS Client
Click Next and the page shown in the following figure appears.

NETGEAR JDGN1000 User Manual
17
Figure 19 Add WPS Client
There are 2 primary methods used in the Wi-Fi Protected Setup:
-PIN entry, a mandatory method of setup for all WPS certified devices.
-Push button configuration (PBC), an actual push button on the hardware or through
a simulated push button in the software. (This is an optional method on wireless
client).
If you are using the PIN method, you will need a Registrar (access point/wireless
router) to initiate the registration between a new device and an active access
point/wireless router. (Note: The PBC method may also need a Registrar when used
in a special case where the PIN is all zeros)
In order to use the push-button for WPS authentication, you must ensure that the
network card support the function. if it supports, you need not to do any configuration.
You can press the WPS button directly to enable the WPS function
5.3 Setup
Choose Setup and the submenus of Setup are shown as below:
Figure 20 Submenus of Setup
5.3.1 Adsl Settings
Choose Setup > Adsl Settings and the following page appears.
Figure 21 DSL ATM interface configuration
In this page, you can add or remove the DSLATM Interfaces.
Click the Add button to display the following page.