Network Electronics ASA VikinXAV0110 User manual

erer
network-electronics.com
Analogue Audio Video
Distributor - 1x10
Rev. 4
VikinX User Manual
AV0110

Network Electronics ASA
Thorøya
P.O. Box 1020
Sandefjord, Norway
Phone: [phone]
Fax: [phone]
e-mail: [email protected]
www.network-electronics.com
Service Phone: [phone]

Contents
Revision history iv
1. General 5
1.1. Specifications 5
1.2. Connection drawing 6
2. Power connection 7
3. Signal termination 7
General Environmental Requirements for VikinX Equipment 8
Product Warranty 9
Materials Declaration and EFUP 10
Materials declaration 10
Environmentally Friendly Use Period (EFUP) 10
Recycling information 10
EC Declaration of Conformity 12

Revision history
Current revision of this document is the uppermost in the table below.
Revision Replaces Date Change Description
4 3 2007-10-23 New front page and removed old logo.
3 2 2007-03-29
Added Materials Declaration and EFUP; updated EC
Declaration of Conformity.
2 1 29/03/04 Updated warranty description.
1 0 10/09/02 Corrected error in specifications
0 - 10/10/00 Initial Revision

AV0110 Rev. 4
5
1. General
The AV0110 is a high bandwidth 1 to 10 video stereo audio distribution amplifier in a single rack space
ultra low profile enclosure. The AV0110 provides looped inputs to create larger systems. High
performance amplifier circuits in SMD technology give maximum signal quality. Extremely low
distortion and SNR figures make this amplifier the first choice for demanding distribution tasks.
1.1. Specifications
AUDIO:
Frequency response: 20Hz – 100kHz ±0.1dB
Crosstalk: > -100dB
THD+N: < 0.003%
SNR: > 90dB ref. to 0dB 20Hz – 20kHz
Number of inputs: 1 looped (stereo)
Input impedance: 47k Ohms
Max input level: +22dBu
Number of outputs: 10 (stereo)
Output impedance: 66 Ohms
Connector: RCA
VIDEO:
Frequency response: 0 – 80MHz -3dB
Differential gain: < 0.07% (3.58/4.43MHz)
Differential phase: < 0.1° (3.58/4.43MHz)
Video S/N Ratio: > 68dB
Gain: 0dB ±0.1dB
Number of inputs: 1 looped
Number of outputs: 10
Impedance: 75 Ohms
Return loss: > 40dB
Max signal: 2 Vp-p
Coupling: DC
Connector: BNC
AC power: External power supply 100 – 260 VAC
DC power: ±15V, connector DB9 male
Dimensions: 483 x 44 x 40 mm (19”, 1RU)

AV0110 Rev. 4
1.2. Connection drawing
Video inputs Video outputs Audio inputs Audio outputs
Power connector
6

AV0110 Rev. 4
7
2. Power connection
Do not connect mains to the desktop power supply before connecting the power supply to the
router.
Connect the DB9 female connector from the desktop power supply to the main unit. Tighten the screws to
assure a proper contact. To connect mains to the desktop power supply you need a mains cord with IEC
320 connector.
The AV0110 is normally delivered with the desktop power model AC ±15V / 10W. Upon customer
request, AV0110 can also be delivered with DC ±15V / 30W, which may be fed by a 36 – 72 VDC mains
power source. A Frame mounted power supply solution is also available.
Please refer to the latest VikinX Product Catalogue for power supply types, or call Network Electronics
ASA for this information.
If an external power supply is used the AV0110 requires ±15V DC with a minimum current of 200mA.
The following pin-out is used on the DB9 connector:
Pin 1 0V
Pin 4 +15V
Pin 8 -15V
3. Signal termination
It is not necessary to terminate unused video outputs.
The DIP switch beside the video input gives the possibility to terminate the video input direct on the
AV0110. In position UP (75) the video input of the AV0110 is terminated with 75 ohms and the LOOP
output is not in use. In position DOWN (HI-Z) the video input is not terminated, the LOOP output can be
used.
If the video signal is routed from the LOOP output to other devices, the end of the loop chain have to
have an internally terminated device or a termination plug. To assure correct frequency response a
precision termination plug with 0,1% tolerance must be used.

AV0110 Rev. 4
8
General Environmental Requirements for
VikinX Equipment
1. The equipment will meet the guaranteed performance specification under the following
environmental conditions:
•Operating room temperature range 0°C to 45°C
•Operating relative humidity range up to 90% (non-condensing)
2. The equipment will operate without damage under the following environmental
conditions:
•Temperature range -10°C to 55°C
•Relative humidity range up to 95% (non-condensing)

AV0110 Rev. 4
9
Product Warranty
The warranty terms and conditions for the AV0110 follow the General Sales Conditions by Network
Electronics ASA. These conditions are available on the company web site of Network Electronics ASA:
www.network-electronics.com

AV0110 Rev. 4
Materials Declaration and EFUP
Materials declaration
For product sold into China after 1st March 2007, we comply with the “Administrative Measure on the
Control of Pollution by Electronic Information Products”. In the first stage of this legislation, content of
six hazardous materials has to be declared. The table below shows the required information.
Toxic or hazardous substances and elements
組成名稱
Part Name
鉛
Lead
(Pb)
汞
Mercury
(Hg)
镉
Cadmium
(Cd)
六价铬
Hexavalent
Chromium
(Cr(VI))
多溴联苯
Polybrominated
biphenyls
(PBB)
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
AV0110 X O O O O O
DP AC ±15V, 10W O O O O O O
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this
part is below the limit requirement in SJ/T11363-2006.
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials
used for this part is above the limit requirement in SJ/T11363-2006.
Environmentally Friendly Use Period (EFUP)
EFUP is the time the product can be used in normal service life without leaking the hazardous materials.
We expect the normal use environment to be in an equipment room at controlled temperature range
(0ºC - 40ºC) with moderate humidity (<90%, non-condensing) and clean air, not subject to vibration or
shock.
Where a product contains potentially hazardous materials, this is indicated on the product by the
appropriate symbol containing the EFUP. The hazardous material content is limited to lead (Pb) in some
solders. This is extremely stable in normal use and the EFUP is taken as 50 years, by comparison with
the EFUP given for Digital Exchange/Switching Platform in equipment in Appendix A of “General Rule
of Environment-Friendly Use Period of Electronic Information Products”. This is indicated by the
product marking:
50
It is assumed that while the product is in normal use, any batteries associated with real-time clocks or
battery-backed RAM will be replaced at the regular intervals.
The EFUP relates only to the environmental impact of the product in normal use, it does not imply that
the product will continue to be supported for 50 years.
Recycling information
Network Electronics ASA provides assistance to customers and recyclers through our web site
http://www.network-electronics.com. Please contact Network Electronics ASA’s Customer Support for assistance
with recycling if this site does not show the information you require.
Where it is not possible to return the product to Network Electronics ASA or its agents for recycling, the
following general information may be of assistance:
10

AV0110 Rev. 4
11
•Before attempting disassembly, ensure the product is completely disconnected from power and signal
connections.
•All major parts are marked or labelled to show their material content.
•Depending on the date of manufacture, this product may contain lead in solder.
•Some circuit boards may contain battery-backed memory devices.

EC Declaration of Conformity
MANUFACTURER Network Electronics ASA
P.B. 1020, N-3204 SANDEFJORD, Norway
AUTHORISED REPRESENTATIVE
(Established within the EEA) Not applicable
MODEL NUMBER(S) AV0110
DESCRIPTION Analogue Audio Video Distributor - 1x10
DIRECTIVES this equipment complies with LVD 73/23/EEC
EMC 89/336/EEC
HARMONISED STANDARDS applied in order to
verify compliance with Directive(s)
EN 55103-1:1996
EN 55103-2:1996
EN 60950-1:2006
TEST REPORTS ISSUED BY Notified/Competent Body Report no:
Nemko 200112142009
TECHNICAL CONSTRUCTION FILE NO Not applicable
YEAR WHICH THE CE-MARK WAS AFFIXED 2001
TEST AUTHORIZED SIGNATORY
MANUFACTURER AUTHORISED REPRESENTATIVE
(Established within EEA) Date of Issue
2007-03-29
Place of Issue
Not applicable Sandefjord, Norway
Name Nils B. Sannes
Position Quality Manager
(authorised signature)